Smart Start IN-HOM User Instructions

The SMART START IN-HOM
during specified "test windows". The device will indicate to the user when a test is required with the use of a display located on top of the
®
IN-HOM unit. The unit will also beep during the required "test windows". An instruction label is located on the left-hand side of the
®
unit. The IN-HOM unit consists of four parts: the IN-HOM
®
S IN-HOM
ETTING UP THE
®
1. Make sure the IN-HOM unit is sitting on a flat, sturdy surface like a table or counter.
2. Connect the power supply cord to the IN-HOM
INITIALIZING, and then BLOW.
3. Place the mouthpiece in the nozzle found on top of the IN-HOM
®
4. For the IN-HOM Cellular unit:
a. This unit transfers data through a cellular connection and thus requires good cellular signal strength just like a cell phone.
b. The display provides an icon that shows the cellular signal strength similar to those used by cellular phones.
c. It is the responsibility of the user to ensure that the IN-HOM
d. Follow the steps below to place the unit and ensure suitable cellular coverage:
i. Place the unit on a flat, sturdy surface that will provide the best cellular signal strength.
ii. Apply power to the unit.
iii. If cellular coverage is weak and the IN-HOM
modem recall mode with a grace period timer. The loss of connection is indicated by no or low bars on the signal strength graphic
and the "RECALL: 5 XX" message being displayed. If this occurs, move the unit until more than half the bars are displayed.
Once the IN-HOM
iv. The IN-HOM
®
HOM
service lockout.
H T T :
OW TO AKE A EST
1. Make sure the display shows the word BLOW. At this time, drink WATER to ensure a clean mouth.
2. Take a deep breath and blow steadily into the mouthpiece until you hear 3 beeps. The 3 beeps mean you can stop blowing. During the test, the
display will show the word TEST.
3. After testing the display will show ANALYZING or other messages listed that indicate an incomplete test (see next page).
PASS
WARN
FAIL
VIOL
ANALYZING
More messages
R "T W
EQUIRED EST INDOWS
You must provide at least one sample with a "PASS" reading during this period. If you skip a "test window", a VIOLATION will be reported. Taking a
test after the "test window" WILL NOT reverse this; however the unit will allow a test.
®
When the IN-HOM unit reaches a scheduled "test window", the unit will beep, the 2 LED lights will flash green, and the display will show "BLOW"
along with a timer indicating how much time you have to take a test. A test MUST be taken during this time. As the "test window" nears the end of the
allotted time, THE UNIT WILL BEEP MORE FREQUENTLY. You can voluntarily take a test outside of a "test window" as long as the device displays
"BLOW". Be sure to drink WATER prior to each and every test.
C Q
USTOMER UESTIONS
If you have questions concerning your IN-HOM
the appropriate department; please follow the directions. Always include your full name, date of birth, area code, phone number, and mention
®
that you are an IN-HOM client.
®
I
N-HOM S
ERVICE
You will be instructed when to bring the IN-HOM
materials. Be sure to make note of your next service appointment date.
SS440-0009-00
®
is a breath-alcohol device with a photo identification feature that requires the user to take a breath test
:
UNIT
®
unit and plug it into an electrical outlet. The unit will activate and the LCD will display
®
Cellular restores cellular coverage, the modem recall lockout notice will disappear.
®
Cellular unit will perform periodic and random data downloads; for this reason, it is important to leave the IN-
Cellular unit plugged in at all times. Unplugging the unit will result in a loss of cellular coverage and could cause a
Test is complete and the alcohol content of the sample was below the Fail level.
Test is complete and the alcohol was detected. But, the sample was below the Fail level.
Test is complete and the alcohol content of the sample was above the Fail level. Continue to take tests until have PASS or
unit returns to the idle state (display = BLOW)
Test is complete and the alcohol content of the sample was above the Violation level. Continue to take tests until have
PASS or unit returns to the idle state (display = BLOW)
The unit is processing the breath sample.
See next Page for more display messages
"
®
unit, call Smart Start toll free at 1-800-880-3394. Our answering system will direct you to
®
device back for service. The device must be returned to Smart Start in the original packaging
®
device, a mouthpiece, a power supply, and power cord.
®
unit.
®
Cellular unit is placed where the cellular signal is strong and reliable.
®
Cellular unit loses cellular connection, the IN-HOM
SMART START IN-HOM
User Instructions
®
Cellular unit could go into a
Rev. 02-04/2014
®