dji Spreading Wings S1000 User Manual
  1. Manuals
  2. Brands
  3. dji Manuals
  4. Quadcopters
  5. S?1000
  6. User manual
dji Spreading Wings S1000 User Manual

dji Spreading Wings S1000 User Manual

Hide thumbs Also See for Spreading Wings S1000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Operating Handbook
Spreading Wings S1000
User Manual
V 1.00
2014.2.24
www.dji.com
1
©2014 DJI Innovations. All Rights Reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Spreading Wings S1000 and is the answer not in the manual?

Questions and answers

Related Manuals for dji Spreading Wings S1000

Summary of Contents for dji Spreading Wings S1000

  • Page 1 Spreading Wings S1000 User Manual V 1.00 2014.2.24 www.dji.com ©2014 DJI Innovations. All Rights Reserved.

  • Page 2: Disclaimer

    This product and manual are copyrighted by DJI Innovations with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI Innovations. No patent liability is assumed with respect to the use of the product or information contained herein.

  • Page 3: About

    An integrated power hub with patented coaxial connectors, built-in high-speed ESCs and motors with high efficiency propellers ensure dynamic stability and maximized power efficiency. Used with a professional DJI multi-rotor autopilot system, the S1000 can hover and fly reliably making it ideal for photography and cinematography.

  • Page 4: Table Of Contents

    Soldering the ESC ....................................24 Remounting the Propeller ..................................24 Propeller Precautions ..................................... 24 Using Propeller Holder ................................... 25 Assembling Motor Vibration Absorbers ............................25 Remounting Landing Gear Servo ............................... 25 Recalibrating Servo Travel ..................................26 ©2014 DJI Innovations. All Rights Reserved.

  • Page 5: Caution

    Use only 6S LiPo batteries for the power supply. Ensure all output signals from M1 to M8 are in proper working order when using the DJI A2 flight control system to avoid damage or injury. Do not overload the system.

  • Page 6: In The Box

    Mounting screws. Thread Locker Fastening screws. Nylon Cable Tie Binding devices and wires. Scissors Cutting Pliers/Dykes Foam Double Sided Adhesive Tape Mounting receiver, controller and other modules. Hot Air Gun Fixing power cable connectors. ©2014 DJI Innovations. All Rights Reserved.

  • Page 7: Mounting Landing Gear

    Insert the landing gear leg into connection point on the center frame. Affix in place with M3x8 screws. Connect springs to both parts to ensure safety. Complete. Spring length is 58.5mm unstretched and 70mm stretched. 70mm ©2014 DJI Innovations. All Rights Reserved.

  • Page 8: Mounting Frame Arms

    Adjust screw mounts of frame arm and center frame. Insert the M4x35 screw from the right of the frame arm as the thread is located on the left of the screw mount. Tighten screw appropriately. Over tightening may lead to connector abrasion. ©2014 DJI Innovations. All Rights Reserved.
  • Page 9 To store, untwist the knob and lower frame arm. Plug ESC signal cable into center frame. Plug power cable into center frame. Heat-shrinkable tubes can be used to stop the connector from coming off. ©2014 DJI Innovations. All Rights Reserved.
  • Page 10 Double check all frame arms. Arms M1 and M2 are the forward facing (nose), arms M5 and M6 are the tail. Seen from the top, motors on arms M1, M3, M5 and M7 rotate counter clockwise while those on arms M2, M4, M6 and M8 rotate clockwise. ©2014 DJI Innovations. All Rights Reserved.

  • Page 11: Mounting Electronics And Wiring

    Eight positions are reserved for mounting a flight control system, wireless video transmission module, receiver, and other items. The DJI A2 flight control system has been used here as an example. If using an A2, follow mounting and wiring instructions found in the A2 flight control system user manual. If using the DJI WK-M flight control system, please refer to the WK-M user manual for connections.
  • Page 12 The other reserved positions are indicated in the diagram below and can be used for mounting a receiver, LED flight indicator, iOSD module and wireless video transmission module. ©2014 DJI Innovations. All Rights Reserved.
  • Page 13 Use glue to install the GPS bracket. Ensure it is firm and reliable before every flight. Always test motors using the Assistant Software after installation. Refer to the “Flight control system user manual” for details. ©2014 DJI Innovations. All Rights Reserved.
  • Page 14 Notes If using a DJI WK-M flight controller, you must use the wires that came with the WK-M. M1 through M6 correspond to each motor number. M7 corresponds to F1 and M8 corresponds to F2 on the WK-M.
  • Page 15 Cable of left servo Cable of right ser vo Notes If right and left servo cables are reversed, landing gear will not be function. Wire neatly to avoid cables being damaged by frame edges. ©2014 DJI Innovations. All Rights Reserved.

  • Page 16: Connecting Xt60 Ports On Center Frame

    Connect PMU power cable to XT60 connector on top of the bottom board. Connect landing gear control board cable to XT60 connector on the bottom of the bottom board. Other connectors can supply power for other DJI devices if required. Installing Battery Soldering battery connectors AS150 anti spark connectors are used.
  • Page 17 Attach battery to battery tray. Do not use an oversized battery. Maximum installation dimension is 80mm X 120mm X 200mm. Insert black connector① then red connector② to power on. Pull out red connector② then black connector① to power off. ©2014 DJI Innovations. All Rights Reserved.

  • Page 18: Setting Landing Gear

    “Recalibrating Servo Travel”. Toggle switch to [Raise] position ONLY AFTER takeoff. Toggle switch to [Lower] position for landing. Tips Servo power will shut off within 3 seconds after the landing gear has reached its target position. ©2014 DJI Innovations. All Rights Reserved.
  • Page 19 Range Working Voltage 3S~6S (LiPo) Input Signal PWM (High-Pulse Width 800us~2200us) Working Current Max 1A@6S Output Signal PWM(Mid Position is 1520us) in 90Hz Working Temperature -20~70 Output Voltage Total Weight 875g Servo Travel (Minimum120 ©2014 DJI Innovations. All Rights Reserved.

  • Page 20: Mounting The Gimbal

    Mounting the Gimbal Before assembling the gimbal, install GCU as shown below. Be sure to install on the side as shown below. A DJI Z15-5D gimbal has been used as an example in the following diagrams. The connectors on gimbal should be removed for better performance, then the gimbal can be mounted to the lower connection points.
  • Page 21 Check that the system’s center of gravity is at the blue line as shown in the below diagram. ©2014 DJI Innovations. All Rights Reserved.

  • Page 22: Appendix

    Solid Red or Green On Motor rotating at full throttle position Solid Yellow On Tips: DJI ESCs are specially designed for multi-rotors. When used with DJI autopilot systems parameters and travel ranges do not have to be calibrated. ©2014 DJI Innovations. All Rights Reserved.

  • Page 23: Specifications

    6.0Kg ~ 11.0Kg Total Weight 4.2Kg Power Battery LiPo (6S、10000mAh~20000mAh、15C(Min)) Max Power Consumption 4000W Hovering Power Consumption 1500W (@9.5Kg Takeoff Weight) Hovering Time 15min (@15000mAh& 9.5Kg Takeoff Weight) Working Environment Temperature C ~ +40 ©2014 DJI Innovations. All Rights Reserved.

  • Page 24: Faq

    Notes: Loose screws cannot be securely locked with thread locker. Propeller Precautions Torque markers on the screws and propeller covers will give you a visual cue to check whether the propellers are loose. Check the torque markers before every flight. ©2014 DJI Innovations. All Rights Reserved.

  • Page 25: Using Propeller Holder

    A soft gasket is part of the vibration absorber. Assembly of the soft gasket must be carried out as per the diagram below. Assembly is the same for CCW and CW propellers. Remounting Landing Gear Servo Remounting servos is not recommended as they come pre-installed. ©2014 DJI Innovations. All Rights Reserved.

  • Page 26: Recalibrating Servo Travel

    During calibration, the left side landing gear will raise and lower. Afterwards, the right side will do the same. After calibration, both left and right parts will be lowered and the LED will be a solid green. This indicates that the landing gear is working properly. ©2014 DJI Innovations. All Rights Reserved.
  • Page 27 If [R] and [L] servo cables are reversed, travel will not be measured correctly. Connect correctly and recalibrate the landing gear using the above steps. SYNERGY POSITIONING SYSTEMS 3/52 Arrenway Drive, Albany Auckland, New Zealand Free Call: 0800-867-266 Phone: +64-9-476-5151 Fax: +64-9-476-5140 Email: info@synergypositioning.co.nz Website: www.synergypositioning.co.nz ©2014 DJI Innovations. All Rights Reserved.

Table of Contents