Otr 2 - Mitsubishi HS-HD2000U Owner's Manual

Recording
Using Standby One-Touch Recording (OTR
Standby One-Touch Recording (also called OTR
begin recording within the next 24 hours and record in 30 minutes intervals. Before
2
you use OTR , make sure the clock has been set correctly.
1 Load a tape with its erasure prevention tab intact into the VCR.
2 Select the recording format. See Selecting Recording Format on page 32.
3 Select the speed at which you would like to record by pressing SP/EP on the
remote control or on the front panel.
4 Set the VCR's input to tuner by pressing INPUT until a channel number is
shown on-screen or on the front panel display. If L1 or L2 appears instead of a
channel number, continue to press INPUT until a channel number appears. To
record channels from a PRIMESTAR
number with the PRIMESTAR light (
5 Press CHANNEL or the number buttons on the remote or the front panel jog
dial to choose the channel to be recorded. If you are using a cable box that the
VCR does not control, select channel 3 or 4 on the VCR, and change the
channel on the cable box.
6 Press PAUSE/%START TIME on the front panel or OTR 2/%START TIME on
the remote to set the time when you wish recording to start (within 24 hours).
The start time is displayed on the front panel. The first time display is the next
half-hour increment from the current time. For example, if it is currently 2:15,
2:30 (next half-hour increment) will be displayed. Similarly, if it is currently
2:40, 3:00 (again, the next half-hour increment) will be displayed. Each time
you press the button, the start time is delayed by 30 minutes.
7 Press REC/˙REC LENGTH or OTR 2/˙REC LENGTH on the remote for
each additional 30 minutes you want to add to the OTR
you see End on the front panel display, the VCR will record until the end of the
tape.
If you have a cable box, a digital cable box, a PRIMESTAR
TM
Network satellite receiver, leave the cable box or receiver turned ON. If the
HS-HD2000U does not control your cable box, leave the box tuned to the
station you wish to record.
After 30 seconds, the power will turn off and the programmed recording light will be
lit. The VCR will automatically turn on at the OTR
begin. When the OTR 2
automatically. If the end of the tape is reached before OTR
will stop and the power will turn off.
Other programs you have set to record may be erased if:
• the start times are before the OTR
• conflicts with the OTR
• starts within one minute or less after the OTR
If you turn the power on while your VCR is in stand-by for the OTR
2
OTR programming will be erased.
2
To cancel OTR
• Turn the power OFF while you are programming the timer.
• Turn the power ON if you have finished programming the timer.
How OTR 2 affects other controls
If you press REC/˙REC LENGTH on the front panel during OTR
minutes will be added to the OTR
ing, you erase the OTR 2
30
® receiver, press INPUT until a channel
) appears on the front panel display.
timer reaches zero, the VCR will stop recording and turn off
IMPORTANT
2
start time
2
2 timer. If you press STOP during OTR
programming.
2
) is a programming method to
2 timer, up to 4 hours. If
®
or a DISH
2 start time and recording will
2 is finished, the VCR
2
finishes
2 , the
2 recording, 30
2
)
CHANNEL
SP/EP
1 START TIME
PROG REC
2 record-
1 START TIME
2 REC LENGTH
SP/EP
INPUT
JOG/CHANNEL
PAUSE REC
2 REC LENGTH
SP
OTR2 CH
PM