Page 1 KADJAR DRIVER’S HANDBOOK...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3: Driving
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
Page 5: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7 RENAULT card: General information, use, deadlocking ........
Page 8 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) 1 Locks all the opening elements. 2 Unlocks all the opening elements. 3 Ignition and front door key. 4 Locking/unlocking the tailgate only. Remote control with switchblade key: 5 Locking/unlocking using the switch- blade key.
Page 9 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. Replacement and additional keys or remote controls.
Page 10: Locking The Doors
RADIO FREQUENCY REMOTE CONTROL UNIT: use Note: The remote control A can be used to lock or unlock the doors and boot. With the engine running, the ignition It is powered by a battery which must switched on and in accessories position be replaced (refer to the information on (refer to “Ignition switch: vehicles with a “Radio frequency remote control: bat-...
Page 11 RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking To activate deadlocking Press button 1 twice in quick succes- sion. The hazard warning lights and indicator lights give two slow flashes and three quick flashes to indicate locking. Special note: deadlocking is not pos- sible if the hazard warning lights or the side lights are lit.
Page 12: Battery Life
“Keycard battery low” appears on the 3 Unlocking/locking the boot. instrument panel (refer to the informa- 4 Switching on the lighting remotely. tion on the “RENAULT card: battery” in section 5). When the battery is flat, you can still lock/unlock and start your vehi- cle.
Page 13 RENAULT CARD: general information (2/2) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in Driver’s responsibility a place where it could be bent or when parking or stopping damaged accidentally, such as in a the vehicle back pocket of a garment.
Page 14 It allows locking/unlocking without input doors. on the card RENAULT when within the Also, in hot and/or sunny weather, access zone 1. please remember that the tempera- ture inside the passenger compart- Note: It is possible to deactivate the ment increases very quickly.
Page 15 “Hands-free” unlocking Locking using button 2 or 3 With the RENAULT card in zone 1, With the doors and boot closed, press press the button 2 on the handle of one button 2 on one of the front door han- of the two front doors: the vehicle will dles or button 3 on the tailgate.
Page 16 7, the message Keycard not detected indicates that Unlocking with the card RENAULT the card is not inside the vehicle. This Press the button 5. avoids you driving away after having...
Page 17 RENAULT CARD: usage (4/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves...
Page 18 RENAULT CARD: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. If the vehicle is equipped with a dead- To activate deadlocking...
Page 19 In some cases, the radio frequency card to unlock the front left-hand remote control or the RENAULT card door; may not work: – to lock each of the doors manually;...
Page 20 Slide the casing 4 upwards and pull the Once you are inside the vehicle, put the key 1. Insert the key 2 into the lock 1 and lock key back in its casing in the RENAULT or unlock the front left-hand door. card. 1.14...
Page 21 When the door is closed, all the doors and the tailgate will be locked. Unlocking the vehicle from the outside is only possible with the RENAULT card Interior locking/unlocking If you need to transport objects with the in the vehicle’s access zone or using boot open, the other opening elements the key.
Page 22: Opening And Closing The Doors
5 indicating the Special feature on vehicles opening elements (door, boot) are open equipped with a RENAULT card If you have switched off the ignition or incorrectly closed. and left the lights switched on, a re- With the doors locked, press button 2...
Page 23 OPENING AND CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Vehicle with manual door locking or to others by starting the engine, activating equipment such as the...
Page 24: Operating Principle
RENAULT ANTI-INTRUDER DEVICE (RAID) Depending on the vehicle, you can also deactivate/activate this function from the instrument panel or, depend- ing on the vehicle, from the multifunc- tion screen. Refer to “Vehicle settings customisation menu” in Section 1, regarding the “Lock doorswhen in motion”...
Page 25: Front Headrests
FRONT HEADRESTS To raise the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary). Press button 3 and lift the headrest to release it. To refit the headrest Check that the headrest rods are clean 2.
Page 26 FRONT SEATS WITH MANUAL CONTROL (1/2) To raise or lower the seat base Move lever 2 as many times as neces- sary upwards or downwards. To tilt the seatback Lift the lever 3 and move the seatback to the desired position. To move the seat forwards or To adjust the lumbar support backwards...
Page 27 FRONT SEATS WITH MANUAL CONTROL (2/2) Repositioning the seat When using the passenger seat in table position, you must not use the two rear Make sure that nothing prevents the seats immediately behind it. seat from moving. – Pull the handle 7 and raise the seat- back, ensuring that it locks firmly in place.
Page 28: Heated Seats
DRIVER’S SEAT WITH ELECTRIC CONTROLS Heated seats With the ignition on, press the switch 4 for the seat desired. The switch warn- ing lights come on. The system automatically decides whether or not the heating is needed. Pressing the button again lowers the temperature.
Page 29: Seat Belts
SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 30 SEAT BELTS (2/4) Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the central display when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and...
Page 31 SEAT BELTS (3/4) Adjusting the height of the Rear seat belts 8 front seat belts The belts are locked, unlocked and adjusted in the same way as the front Use button 7 to adjust the seat belt belts. height so that the shoulder strap is worn as shown previously.
Page 32 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 33 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
Page 34: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Airbags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system.
Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 37 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 38 SIDE PROTECTION DEVICES Side Airbags An airbag can be fitted to each front seat and the rear side seats, which are deployed on the side of the seat (door side) to protect the occupants in the case of a severe side impact. Curtain Airbags These are airbag fitted along the sides of the vehicle in the ceiling which trigger...
Page 39: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT Operating faults All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when it inflates. This warning light comes on when the engine is started and then The airbag is designed to complement the action of the seat belt.
Page 40: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 41 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 42 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 43: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
Page 44 CHILD SAFETY: choosing a child seat mounting (2/2) The rings are located on the rear seat- backs and indicated by the symbol In all cases, attach the strap hook to the corresponding ring 3 and 4 and place the seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.
Page 45: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, if neces- child seats. The diagram on the follow- sary, the seat may be advanced (so as The laws concerning children travel- ing page shows you how to attach a to leave enough space in the rear seats...
Page 46 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat Rear centre seat A carrycot can be installed across the Check that the belt is suitable for secu- vehicle and will take up at least two ring your child seat.
Page 47 CHILD SEATS: attachment by seat belt (1/3) ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬...
Page 48 CHILD SEATS: attachment by seat belt (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Front passenger Type of child seat Weight of the child Rear side seats Rear centre seat seat (1)
Page 49 CHILD SEATS: attachment by seat belt (3/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 50 CHILD SEATS: attachment using the ISOFIX system (1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Five-seater version Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats Rear centre seat...
Page 51 CHILD SEATS: attachment using the ISOFIX system (2/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. (1) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without allowing it to come into contact with the child seat.
Page 52 CHILD SEATS: attachment using the ISOFIX system (3/3) Child seat fitted using the ISOFIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
Page 53: Deactivating, Activating The Front Passenger Airbag
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the airbags: with the vehicle stopped and the ignition off, passenger airbags push and turn lock 1 to the OFF posi- (on equipped vehicles) tion. You must deactivate the devices in ad- With the ignition on, you must check dition to the front passenger seat belt before fitting a child seat in the front...
Page 54 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
Page 55 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
Page 56: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1.50...
Page 57: Instrument Panel
8 Steering column stalk for wind- selector or, depending on the vehi- – activation/deactivation of the Stop screen and rear screen wash/ cle, traction control. and Start function. wiper. 18 Cruise control/speed limiter main 9 Engine start/stop button (vehicle control. with RENAULT card). 1.51...
Page 58 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 10 11 1.52...
Page 59 – remote radio and navigation 5 Multifunction screen. system. 19 Engine start/stop button (vehicle with RENAULT card). 6 Controls for: 13 Steering column stalk for wind- – access the main menu, screen and rear screen wash/...
Page 60 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Side light warning light Left-hand direction indicator š tell-tale Main beam headlight tell- Right-hand direction indica- á tale tor tell-tale Dipped beam headlight tell- Low fuel level warning light tale It lights up orange when the ig-...
Page 61 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Brake circuit fault warning Oil pressure warning light À light It lights up when the ignition or It lights up when the ignition or the the engine is switched on and goes off engine is switched on and goes off after after a few seconds.
Page 62 WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Toxic Fume Filter System Anti-lock braking warning Ä Warning Light light It lights up when the ignition or the For vehicles equipped with this option, engine is switched on and goes off after the light comes on when the ignition is a few seconds.
Page 63 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Rear seat belt reminder (depending Air bag warning light å on vehicle) This warning light will be dis- played on the instrument panel when ß...
Page 64 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Speed limiter and cruise Assisted parking brake fault Î¦ control indicator lights light See the information on the “Speed lim- Please refer to the information on the iter”...
Page 65 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder This lights up in the rear-view mirror when the ignition is started then, if the driver or front passenger seat belt (if this seat is occupied) is not fastened...
Page 66 DISPLAYS AND INDICATORS (1/2) Instrument panel A Rev counter 4 Instrument panel in miles (option to switch to km/h) (graduations x 1000) Depending on the vehicle, you can cus- Vehicles not fitted with a navigation tomise your instrument panel with the system content and colours of your choice.
Page 67: Coolant Temperature
DISPLAYS AND INDICATORS (2/2) Vehicles fitted with a navigation Coolant temperature Engine oil level low warning system indicator 6 When the engine is started, the instru- On the multifunction screen, select ment panel display A alerts you when “System” , “User profile” and “Unit”. the minimum oil level is reached.
Page 68: On-Board Computer 1
TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on the con- trol 2 (the display depends on the vehi- cle equipment and country): a) total mileage and trip mileage re- corder;...
Page 69 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
Page 70 ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Fuel used b) Journey parameters. Fuel used.
Page 71 ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range e) Estimated range with remaining fuel. The value is displayed after driving 400 metres. 541 km Distance f) Distance travelled since last reset.
Page 72 ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message h) Mileage before service or oil change. Mileage before service Service in With the ignition switched on, the engine not running and Service Intervals...
Page 73 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) h) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
Page 74 ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected i) Tyre pressure monitor. Refer to the information on the “Tyre pressure monitor” in Section 2. j) Trip log.
Page 75 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
Page 76 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 77 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.
Page 78: Vehicle Settings Customisation Menu
VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings Select the function to modify: a) unlocking the driver’s door; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome; g) reading lamp in automatic mode;...
Page 79: Navigation System
VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings If you select either “PARKING ASSIST VOLUME” or “LANGUAGE”, you will Browse using the control 4 to select the have to make a further selection (sound function to adjust: volume of the parking distance control a) Lock doorswhen in motion;...
Page 80: Steering Wheel/Power-Assisted Steering
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Page 81: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (sig- nalling a risk of ice on the road). Display 1 Vehicles fitted with a touchscreen multimedia screen, navigation aid systems, etc.
Page 82: Rear-View Mirrors
(ON or OFF). Depending on the selected choice, the door mirrors will fold out: – when the ignition is next switched on (function deactivated); – upon detecting the RENAULT card or upon unlocking the vehicle (func- tion activated) Door mirrors Adjustment...
Page 83 REAR-VIEW MIRRORS (2/3) Position memory Recalling the memorised position – Adjust the door mirrors (see previous paragraphs); From the multifunction screen, select – from the multifunction screen, select menu “Vehicle”, “Seats”, “Settings” then menu “Vehicle”, “Seats”, “Settings” “Position” and select “Recall”. then “Position”...
Page 84: Interior Rear View Mirror
REAR-VIEW MIRRORS (3/3) Rear view mirror without lever 2 The rear-view mirror darkens automati- cally at night if you are being followed by a vehicle with its lights on. Interior rear view mirror Its position can be adjusted. Rear-view mirror with lever 2 For night driving, to avoid being dazzled by the headlights of the car behind you, flip the small lever 2 located behind the...
Page 85: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/5) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the in- strument panel comes on. Automatic operation Turn ring 3 until the AUTO symbol is op- posite mark 2: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
Page 86 EXTERIOR LIGHTING AND SIGNALS (2/5) Automatic main beam Activation Turn ring 3 until the AUTO symbol is op- headlights posite mark 2. Depending on the vehicle, this system Push stalk 1 to activate the main beam switches the main beam headlights on headlights.
Page 87: Daytime Running Lights
EXTERIOR LIGHTING AND SIGNALS (3/5) Daytime running lights Switching off the lights function There are two possibilities: – manually, move ring 3 to position 0; The daytime running lights come on – automatically, the lights will go out automatically (at the front only) with no when the engine is switched off, the action on stalk 1 at the time of starting driver’s door is opened or the vehicle...
Page 88 With the engine and lights off and ing the RENAULT card or when the ve- ring 3 in position 0 or AUTO, pull hicle is unlocked. stalk 1 towards you: the dipped beam...
Page 89: Front Fog Lights
EXTERIOR LIGHTING AND SIGNALS (5/5) Rear fog lights Switching off the lights Turn centre ring 5 on the stalk Turn the ring 5 again until the mark 4 until the symbol faces mark 4, then re- is opposite the symbol for the fog light lease it.
Page 90: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 91: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) For manual settings Examples of positions for adjusting control A according to the load Driver alone or with front passenger Driver with one front passenger and two or three rear passengers On vehicles fitted with this function, control A allows you to adjust the height Driver with a full car of passengers, luggage or (load) of the beams according to the load.
Page 92 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left- hand drive vehicle (or vice versa), you must adjust your lights tempo- rarily during your stay. Temporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors.
Page 93: Windscreen Wipers
WINDSCREEN WASH/WIPE (1/6) Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Vehicle fitted with intermittent Special note water; When driving the vehicle, the wiping windscreen wipers –...
Page 94 WINDSCREEN WASH/WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of re- duced visibility, the driver should manually activate the wipers;...
Page 95 WINDSCREEN WASH/WIPE (3/6) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the ve- intermittent wiping. Contact an au- hicle stops. For example, fast wiping thorised dealer.
Page 96: Service Position
WINDSCREEN WASH/WIPE (4/6) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the winds- the blades.
Page 97: Windscreen Washer
WINDSCREEN WASH/WIPE (5/6) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer.
Page 98: Headlight Washers
WINDSCREEN WASH/WIPE (6/6) Note: To ensure the headlight washers op- erate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.
Page 99: Rear Screen Wiper
REAR SCREEN WASH/WIPE (1/2) To stop the operation, pivot ring 3 again. Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate auto- matic wiping. Follow usage recommendations. Check the condition of the wiper blades.
Page 100 REAR SCREEN WASH/WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper (depending on the vehicle) will try to sweep away all the obstacles. If an obstacle prevents the blade from Engaging reverse gear triggers inter- moving, it can be stopped.
Page 101: Fuel Tank (Filling With Fuel)
FUEL TANK (1/3) Petrol version It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover A. Refer to Section 6 for information on “Engine specifications”. Diesel version Only use diesel fuel which complies with the information on the label located inside the cover A.
Page 102 FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts...
Page 103 Vehicles with RENAULT card thorised dealer. Persistent fuel odour With the card RENAULT in the pas- If you notice a persistent senger compartment, press the start fuel odour you should: button 4 without pressing any of the pedals.
Page 104 1.98...
Page 105 Starting, stopping the engine: vehicle with Renault card ....... . .
Page 106: Running In
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.
Page 107: Ignition Switch
IGNITION SWITCH: vehicle with key Ignition position M. The ignition is switched on: Start position D If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts.
Page 108: Starting, Stopping The Engine: Vehicle With Key/Remote Control
STARTING, STOPPING THE ENGINE: vehicle with key Diesel versions É – Turn the ignition key to the “Ignition on” position M, and hold this position until the engine pre- heating light goes off; – turn the key to starter position D without depressing the accel- erator pedal;...
Page 109: Starting, Stopping The Engine: Vehicle With Renault Card
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (1/3) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. Never leave your vehicle with the RENAULT card...
Page 110 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (2/3) Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out.
Page 111 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (3/3) If the RENAULT card is no longer in the Driver’s responsibility passenger compartment or if the card battery is low when you try to switch Never leave an animal, the engine off, the message “No key- child or adult who is not card Press and hold”...
Page 112: Stop And Start Function
STOP AND START FUNCTION (1/4) This system enables a reduced fuel For manual gearboxes: consumption and lower greenhouse – the gearbox is in neutral; gas emissions. The system is activated automatically – the clutch pedal is released. If the when the vehicle is started. warning light flashes, this While driving, the system stops the...
Page 113 STOP AND START FUNCTION (2/4) Preventing the engine from Conditions for coming out of standing by engine standby In certain situations, such as negotiat- For automatic gearboxes: ing a crossroads for instance, it is pos- – the brake pedal is released, position sible (with the system activated) to keep D engaged or, the engine running so as to be ready to...
Page 114 Special cases for vehicles – parking distance control is in opera- tion; standby of the engine with a RENAULT card – for vehicles with automatic gear- Certain conditions prevent the system With the engine on standby (traffic jam, boxes, the gradient is steeper than from using the engine standby function, traffic lights, etc.), if the driver unfas-...
Page 115 STOP AND START FUNCTION (4/4) Special feature of the automatic The system is automatically reacti- engine re-start vated each time the vehicle is started (see “Starting, stopping the engine” in Under certain conditions, the engine Section 2). can restart on its own in order to guar- antee your safety and comfort.
Page 116: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 117: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 118: Gear Lever
GEAR LEVER Selecting reverse gear The ring 2 has to be lifted up to the gear lever knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected with the ignition on. Gear lever Vehicles with manual gearbox: refer to the grid on the gear lever knob 1.
Page 119: Handbrake
HANDBRAKE When stationary, and de- pending on the slope and/or vehicle load, it may be nec- essary to pull up the hand- Handbrake brake at least two extra notches and engage a gear (1 or reverse gear) To release: for vehicles with a manual gearbox Pull lever 2 up slightly, press button 1 or position P for vehicles with an au- and then lower the lever to the floor.
Page 120: Electronic Parking Brake
ELECTRONIC PARKING BRAKE (1/3) Automatic operation Note: To indicate that the electronic parking The assisted parking brake immobilises brake is released, a beep sounds and the vehicle when stopping the engine the message “Apply parking brake” ap- (and not when the engine is on pears on the instrument panel: standby for vehicles fitted with the Stop and Start function).
Page 121: Manual Operation
ELECTRONIC PARKING BRAKE (2/3) Brief stop Special cases To manually activate the electronic To park on a slope or while towing a parking brake, (when stopping at a red trailer, for example, pull switch 1 for light, or stopping when the engine is a few seconds to gain the maximum running, etc.): pull and release switch 1.
Page 122 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults gearbox © – If there is a fault, the warning light illuminates on the instrument For safety reasons, automatic release panel accompanied by the “Check is deactivated when the driver’s door parking brake”...
Page 123: Eco Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- Gear change indicator 2 cordance with a standard regulatory Depending on the vehicle, to obtain op- method. Identical for all manufactur- timum consumption levels, a warning ers, this enables vehicles to be com- light on the instrument panel lets you pared with one another.
Page 124 DRIVING ADVICE, ECO-DRIVING (2/5) This indicates: – average fuel consumption; – number of miles/kilometres travelled; – number of miles/kilometres saved. This corresponds to driving without fuel consumption (deceleration and/ or foot off the accelerator pedal). An overall rating from 0 to 100 is dis- played to let you assess your eco driv- ing performance.
Page 125 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode Disabling the function Press switch 4. ECO mode is a function which opti- mises fuel consumption. This acts on The warning light goes out on all power consuming elements (engine the instrument panel to confirm deac- power, switching gears for vehicles tivation.
Page 126 DRIVING ADVICE, ECO-DRIVING (4/5) – Do not overrev the engine in the in- – Bad weather, flooded roads: termediate gears. Do not drive through You should always use the highest floods if the water is gear possible. above the lower edge of –...
Page 127 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 128: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
Page 129: Environment
– In all cases, comply with local legis- use, and therefore to consume less fuel This commitment is illustrated by the lation. (eg. 140 g/km, equivalent to 5.3 l/100 Renault eco² signature. km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...
Page 130: Tyre Pressure Monitoring System
TYRE PRESSURE MONITORING SYSTEM (1/3) If the vehicle is equipped with the func- With the ignition on: tion, this system monitors the tyre pres- – make short presses on the control 2 sure. to select the tyre pressure display (see “On-board Computer” in Section 1);...
Page 131 TYRE PRESSURE MONITORING SYSTEM (2/3) “Puncture” A wheel B shown red on the display 1, together with the warning light 4 and a beep indicates that the affected tyre is punctured or severely underin- flated. Replace it or contact an autho- rised dealer if it is punctured.
Page 132: Emergency Spare Wheel
TYRE PRESSURE MONITORING SYSTEM (3/3) Replacing wheels/tyres Tyre repair product and “Tyre location failure” inflation kit This message appears when driving if This system requires specific equip- one or more wheels have been fitted ment (wheels, tyres, hubcaps, etc.). Because the valves are specially de- with sensors not recognised.
Page 133 DRIVING CORRECTION DEVICES AND AIDS (1/10) ABS (anti-lock braking Depending on the vehicle, they will con- sist of: system) Under heavy braking, the ABS prevents – ABS (anti-lock braking system) ; the wheels from locking, allowing the – ESC (electronic stability control) stopping distance to be managed and with understeer control and trac- keeping control of the vehicle.
Page 134 DRIVING CORRECTION DEVICES AND AIDS (2/10) Operating faults: © – lit up on the in- strument panel alongside mes- sages “Check ABS”, “Check braking system” and “Check ESC”: indicates the ABS, ESC and emergency brake assist are deactivated. Braking is always enabled;...
Page 135: Electronic Stability Control
DRIVING CORRECTION DEVICES AND AIDS (3/10) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC”...
Page 136: Emergency Brake Assist
DRIVING CORRECTION DEVICES AND AIDS (4/10) The traction control system offers ad- ditional safety. It is recommended that you do not drive with the function di- sabled. Correct this as soon as pos- sible by pressing the switch 1 again. Note: The function is reactivated auto- matically when the ignition is switched on or when a speed of approximately...
Page 137 DRIVING CORRECTION DEVICES AND AIDS (5/10) Advanced traction control “Soft ground” mode Turn the selector 2: the integrated If fitted on the vehicle, grip control makes it easier to control the vehicle on warning light comes on, along low grip surfaces (soft ground, etc.). with the instrument panel message “Non grip road mode on”.
Page 138: Active Emergency Braking
DRIVING CORRECTION DEVICES AND AIDS (6/10) If the driver depresses the brake pedal and the system still detects a risk of col- lision, the brake force is increased. If the driver fails to react following an alert of an imminent collision, the system activates the brakes.
Page 139 DRIVING CORRECTION DEVICES AND AIDS (7/10) Press the switch 7 OK again to activate or deactivate the function: function activated < function deactivated The warning light is displayed on the instrument panel when the system is deactivated. This system is reactivated each time the ignition is switched on.
Page 140 DRIVING CORRECTION DEVICES AND AIDS (8/10) Operating faults Active emergency braking When the system detects an operating This function is an additional driving aid. However, this function is not fault, the warning light appears under any circumstances intended to replace the due care and attention on the instrument panel along with the of the driver, who should at all times be in control of the vehicle.
Page 141 DRIVING CORRECTION DEVICES AND AIDS (9/10) Active emergency braking Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. –...
Page 142 DRIVING CORRECTION DEVICES AND AIDS (10/10) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle from rolling backwards by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to de- press the accelerator pedal.
Page 143: Transmission: 4-Wheel Drive (4Wd)
TRANSMISSION: 4-wheel drive (4WD) (1/4) Mode selector “2WD" mode Depending on the road conditions, turn- To activate this mode, turn the selec- ing the selector 1 enables the following tor 1 to the “2WD” position. The warn- modes to be selected: ‘...
Page 144 TRANSMISSION: 4-wheel drive (4WD) (2/4) “4WD Lock" mode After one minute, the system switches This problem may be resolved by to “2WD” or “AUTO” mode depending changing the tyres. Always use four To activate this mode, turn selector 1 to on the position of the selector.
Page 145 TRANSMISSION: 4-wheel drive (4WD) (3/4) Operating faults After stopping the engine, the system Electronic stability program and may take up to five minutes to cool traction control when driving off- If the system detects an operating down. road fault, it automatically switches to “2WD” If the system detects excessive wheel- When driving on soft ground (sand, ‘...
Page 146 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...
Page 147: Lane Departure Warning
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
Page 148 LANE DEPARTURE WARNING (2/3) Activation/deactivation Vehicles not fitted with a navigation The function is set to notify the system driver if: Vehicles fitted with a navigation – the vehicle speed is greater than ap- Press the switch 3. system proximately 45 mph (70 km/h); From the multifunction screen 2: select Operation –...
Page 149 LANE DEPARTURE WARNING (3/3) Adjustment – repeatedly press control 6 up or down until you reach the “Lane de- Vehicles fitted with a navigation parture warning settings” menu, then system press the switch 5 OK. – Volume: adjust the alert volume to From the multifunction screen 2, select one of three levels;...
Page 150 BLIND SPOT WARNING (1/4) This function is an addi- tional aid which indicates other vehicles in the blind spot area. This system alerts the driver to other Special feature It can never in any case be a subs- vehicles in the detection zone A. Make sure that the sensors are not ob- titute for care nor for the driver’s scured (by dirt, mud, snow, etc.).
Page 151 BLIND SPOT WARNING (2/4) – repeatedly press control 5 up or down until you reach the “Blind spot alert” menu, then press the switch 4 – Press the switch 4 OK again to acti- vate or deactivate the function. Activation/deactivation Vehicles not fitted with a navigation system Vehicles fitted with a navigation...
Page 152 BLIND SPOT WARNING (3/4) Display B The function is activated and has not detected any vehicles. Display C Initial warning: the indicator light 4 shows that a vehicle has been detected in the blind spot. Display D When the direction indicator is activa- ted, the indicator light 4 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
Page 153: Blind Spot Alert
BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 4 (display B) flashes three times.
Page 154 CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) Switching on Press switch 1 on side . The indica- tor light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.
Page 155: Speed Limiter
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by It is possible to exceed the limit speed repeatedly pressing the switch 2: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 156 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 3 ((R)). Putting the function on Switching off the function standby The speed limiter function is deacti- vated if you press switch 1: in this case The speed limiter function is sus- a speed is no longer stored.
Page 157: Overspeed Alert
OVERSPEED ALERT (1/3) Operating principle Once the speed limiter is activated, you can adjust the speed limiter indication The system detects speed limit signs displayed by the system. on the side of the road and displays the In the event of exceeding the speed speed limit.
Page 158 OVERSPEED ALERT (2/3) – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. – Press OK to turn the function on or off. Varying the limit speed If the speed limiter notification differs from the detected speed value, press and hold the switch 4: –...
Page 159 OVERSPEED ALERT (3/3) Operating fault This function is an additional driving aid. However, this function is not The system cannot detect the speed under any circumstances intended to replace the due care and attention limit if: of the driver, who should at all times be in control of the vehicle. –...
Page 160: Cruise Control
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to Controls Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- 1 Main “On/Off”...
Page 161 CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Activating cruise control At a steady speed (above approx. 20 mph (30 km/h)), press the switch 2 on side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control”...
Page 162 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While overtaking, the cruis- ing speed flashes red on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 163 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 3 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 164: Parking Distance Control
PARKING DISTANCE CONTROL (1/5) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to This function is an addi-...
Page 165 PARKING DISTANCE CONTROL (2/5) Note: the display 2 shows the vehicle Operation surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are before the side detection is activated. detected.
Page 166 PARKING DISTANCE CONTROL (3/5) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
Page 167 PARKING DISTANCE CONTROL (4/5) System sound Enables the system sound to be se- lected from a choice of 3. Deactivating the system sound Activate or deactivate the parking dis- tance control sound. Note: If you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
Page 168 PARKING DISTANCE CONTROL (5/5) Automatic deactivation of the Operating faults parking distance control When the system detects an operating fault, a beep sounds for approximately The system deactivates: 3 seconds each time reverse gear is se- – when the vehicle speed is above ap- lected and is accompanied by the mes- proximately 6 mph (10 km/h);...
Page 169: Reversing Camera
REVERSING CAMERA (1/2) Operation Fixed gauge 3 4 moving guide line: The fixed clearance gauge comprises This is shown in blue on the multifunc- Moving into reverse gear, the camera 1 coloured markers A, B and C, indicat- tion screen 2. It indicates the vehicle located on the tailgate provides a view ing the distance behind the vehicle: trajectory according to the position of...
Page 170 REVERSING CAMERA (2/2) You can also adjust the camera image settings (brightness, contrast, etc.) The screen shows a reverse mirror Activating, deactivating the image. This function is an additional reversing camera The frames are a representation aid. It cannot, therefore, projected onto flat ground;...
Page 171: Assisted Parking
ASSISTED PARKING (1/4) This function assists with parking ma- Switching on Special features noeuvres. With the vehicle at a standstill or driv- Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. ing at less than 6 mph (10 km/h), press cated by arrows 3 are not obscured (by You only control the pedals and the switch 1.
Page 172 ASSISTED PARKING (2/4) Choice of manoeuvre Operation Your speed should not exceed around 4 mph (7 km/h). The system can perform four types of Parking manoeuvres: Once the warning light on the As long as the vehicle speed is less –...
Page 173 ASSISTED PARKING (3/4) Your speed should not exceed around In this case, the reason for suspending 4 mph (7 km/h). the manoeuvre will be displayed on the Once in position to exit the space, the multifunction screen. system will notify you of the end of the Make sure: manoeuvre.
Page 174 ASSISTED PARKING (4/4) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location.
Page 175: Selector Lever
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In most road conditions you will en- counter, you will not need to touch your lever again: the gears will change au- tomatically at the right time and at the most suitable engine speed because the automatic system takes into ac- count the vehicle load and road contour...
Page 176: Automatic Gearbox
AUTOMATIC TRANSMISSION (2/3) Special cases Special circumstances In certain driving conditions (for exam- – If the bends and road surface do ple, engine protection, operation of the not allow you to stay in automatic Electronic Stability Programme: the au- mode (e.g. in the mountains), we tomatic system may change gear auto- recommend that you change to matically.
Page 177: Automatic Transmission
AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the – when driving, if the ‘check gearbox’ lever to position P while keeping your message appears on the instrument foot on the brake pedal: the gearbox is panel, it indicates a fault.
Page 178 2.74...
Page 179: Your Comfort
Section 3: Your comfort Air vents............... Manual air conditioning and heating system .
Page 180: Air Vents
AIR VENTS, air outlets (1/2) 1 left-hand air vent 2 windscreen demisting vents 3 centre air vents 4 side window demister outlets 5 right-hand air vent 6 multifunction screen 7 footwell heater outlets for front pas- sengers 8 footwell heater outlets for rear pas- sengers (depending on the vehicle)
Page 181 AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Air flow Air flow Move the control knob 10 (beyond the Move the control knob 11 (beyond the resistance point). resistance point). Upwards: closed. Upwards: closed. Down: maximum air flow. Down: maximum air flow.
Page 182 MANUAL AIR CONDITIONING (1/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light on) or off (indicator light off) using the button 7. The air conditioning system is used for: – lowering the temperature inside the passenger compartment;...
Page 183: Manual Air Conditioning
MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 8 to choose the distribution option. The air distribution is displayed on the indicator D. The air flow is directed to the õ...
Page 184 MANUAL AIR CONDITIONING (3/3) Rear screen de-icing/ demisting With the engine running, press button 6. The operating tell-tale comes This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehi- cles). To exit this function, press button 6 again.
Page 185: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/6) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
Page 186 AUTOMATIC CLIMATE CONTROL (2/6) Temperature adjustment DUAL function setting The displayed temperature values show a comfort level. Press button 12 to activate. There are two types of settings: When starting the engine, increas- Use the control 2 to adjust the left side –...
Page 187 AUTOMATIC CLIMATE CONTROL (3/6) Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press the switch 8 to force activation Preferably, use automatic mode. (the integrated warning light comes on) In automatic mode (warning light 7 or stop the air conditioning (the inte- is on), all climate control functions...
Page 188 AUTOMATIC CLIMATE CONTROL (4/6) Clear View function This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated. Press button 3 –...
Page 189 AUTOMATIC CLIMATE CONTROL (5/6) De-icing or demisting the Rear screen de-icing/ windscreen demisting (depending on the vehicle) Press button 11 – the integrated indi- With the engine running, press the cator light comes on. This function en- button 1 – the integrated indicator will ables rapid demisting or de-icing of the come on.
Page 190 AUTOMATIC CLIMATE CONTROL (6/6) Recycling This function is managed automati- cally (operation is confirmed by warn- ing light D), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
Page 191: Air Conditioning: Information And Advice On Use
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
Page 192: Outside Air Quality And Deodorisation Functions
OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Take care Deodorization cycle With the air conditioning switched Deodorisation function on, from the screen A, select Menu, This reduces unpleasant odours in the Vehicle, Take care. passenger compartment. Outside air quality Deodorization cycle –...
Page 193: Electric Windows
Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child (or a pet) un- Press or pull the switch to raise or lower supervised, even for a short while.
Page 194: Fixed Glass Roof
ELECTRIC WINDOWS /FIXED SUNROOF (2/2) One-touch mode Operating faults Depending on the vehicle, this mode In case of a fault when closing a window, works in addition to the operation of the the system reverts to normal mode: electric windows described previously. pull the switch concerned up as often It is only fitted to the driver’s window.
Page 195: Interior Lighting
INTERIOR LIGHTING Map reading lights Note: For vehicles fitted with a naviga- Boot lights tion system, you can use the multifunc- Press switch 1 to get: Light 2 comes on when the boot is tion screen to deactivate/activate the opened. –...
Page 196 PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5) Front door storage pockets 1 Front sun visor Centre console storage compartment 5 They can hold a 0.5-litre bottle. Lower sun visor 2. Sun visor storage 3 This can be used for storing motorway tickets, cards, etc. Courtesy mirrors Nothing should be placed Ensure that no hard, heavy...
Page 197 PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5) Cup holders 6 Storage compartment under the front central armrest A This can be used for storing a mobile (depending on the vehicle) ashtray, cup holder, etc. Lift the control 8 and raise the arm- This storage compartment has a re- rest 7.
Page 198 PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5) Glovebox Grab handle 11 Clothes hooks 12 To open the glovebox, lift the catch 10. This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
Page 199 PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5) Storage 13 Front seat storage pockets 14 Rear centre console storage compartments 15 Can hold loose change, etc. 3.21...
Page 200 PASSENGER COMPARTMENT STORAGE, FITTINGS (5/5) Rear armrest with cup holder Rear door storage compartment 17 Pull down the armrest 16. When turning corners, accelerating or braking, Ensure that no hard, heavy ensure that the recepta- or pointed objects are cle being held by the cup placed in the “open”...
Page 201: Ashtray, Cigarette Lighter
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET Ashtray 1 Accessories sockets 2 To open, lift the cover. To empty, pull the They are designed for connecting ac- ashtray towards you and it will be re- cessories with a maximum power rating leased from its housing. of 120 Watts (voltage: 12V) which have been approved by our Technical Department.
Page 202 REAR HEAD RESTS Position for use To raise the headrest Raise the headrest as far as possible to Raise the headrest as far as it will go, use it in the high position. Check that it then press button A and remove the is correctly locked.
Page 203 REAR BENCH SEAT (1/2) To replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. When refitting the seat- back, make sure it is cor- rectly locked in place. To manually fold down the If seat covers are fitted, make sure these do not prevent the seatbacks...
Page 204 REAR BENCH SEAT (2/2) To automatically fold down Conditions of use Use restriction the seatbacks (flat position) – Vehicle stationary; It is forbidden to drive with a seatback – boot lid open; or a front seat folded down when there From the boot, pulling the control 2 en- –...
Page 205: Boot
BOOT To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.
Page 206: Luggage Compartment Cover
LUGGAGE COMPARTMENT COVER To remove the flexible Refitting the luggage Luggage compartment cover section of the luggage cover compartment cover storage Pull handle 1 gently to release the pins Position the side 3 of the luggage com- Version without emergency spare from their mounting points located on partment cover in its housing, press the wheel...
Page 207 BOOT FITTINGS (1/2) Mobile floor 1 Intermediate position Storage position (depending on the vehicle) This enables you to compartmentalise This allows for more space to store the boot into two separate spaces. things in the boot. It is made up of two independent and interchangeable parts, A and B.
Page 208 BOOT FITTINGS (2/2) Bag hooks 4 Anchorage points Maximum weight per hook: 5 kg. Attachment points 5 If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. 3.30...
Page 209: Transporting Objects In The Luggage Compartment
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (exam- ple B).
Page 210 TRANSPORTING OBJECTS towbar Maximum dimension A: 1029 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. For fitting and conditions of use, If the towbar ball obscures the regis- refer to the equipment’s fitting in- tration plate or the rear fog lights, it structions.
Page 211 ROOF BARS (1/2) Accessing the mounting Vehicles not fitted with longitudinal roof bars points Open the doors to access the fixing Vehicles fitted with longitudinal roof points 3. bars The attachment inserts 2 are located on the longitudinal roof bars 1. If original roof bars, ap- proved by our Technical Department, are supplied...
Page 212: Roof Bars
ROOF BARS /SPOILER (2/2) Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 213: Multimedia Equipment
MULTIMEDIA EQUIPMENT Multimedia systems Hands-free telephone integrated control 1 Multimedia touchscreen; 2 Multimedia sockets; For equipped vehicles, use the steering 3 Steering column controls; wheel controls 4. 4 Steering wheel controls; 5 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
Page 214 3.36...
Page 215 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 216: Bonnet
BONNET (1/2) To open, press the control 1. Unlocking the bonnet catch To open, raise the bonnet slightly, then When working in the engine lift the paddle 2 at the centre point of compartment, ensure that the bonnet. the windscreen wiper stalk is in the park position.
Page 217: Closing The Bonnet
BONNET (2/2) After carrying out any work in the engine compart- ment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire. Closing the bonnet Before closing the bonnet, make sure that nothing has been left in the engine compartment.
Page 218: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – Remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 219: Engine Oil Level: Topping Up/Filling
ENGINE OIL LEVEL: topping up/filling (1/2) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
Page 220: Engine Oil Change
ENGINE OIL LEVEL: topping up, filling OIL CHANGE (2/2) Oil change Engine oil grade Service interval: refer Refer to the maintenance document for Maintenance Document for your vehi- your vehicle. cle. Oil change capacity Please refer to the maintenance docu- Filling: take care when ment for your vehicle, or contact an au- topping up the oil that...
Page 221: Levels
LEVELS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 222: Brake Fluid
LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net- work or web site.
Page 223: Windscreen Washer Reservoir
LEVELS /FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Before performing any Windscreen washer reservoir Checking the level...
Page 224 TYRE PRESSURE (1/2) E: front tyre pressure. F: rear tyre pressure. G: tyre pressure for the emergency spare wheel. Vehicle fitted with a tyre pressure monitoring system In cases of under-inflation (puncture, low pressure, etc.), warning light lights up on the instrument panel. Please refer to the information on the “Tyre pressure monitoring system”...
Page 225: Tyre Pressures
TYRE PRESSURES (2/2) Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- creased by 0.2 bar. Please refer to the information on “Weights”...
Page 226: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your ve- hicle:...
Page 227: Replacing The Battery
BATTERY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 eye protection required; –...
Page 228: Bodywork Maintenance
BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
Page 229 BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
Page 230: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 231 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 232 4.18...
Page 233: Practical Advice
RENAULT card: battery ........
Page 234: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emer- gency spare wheel disappears from the instrument panel display).
Page 235 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) Emergency spare wheel A To get to it: – open the tailgate; – Depending on the vehicle, lift up the mobile floor; – lift the boot carpet; – remove the tool kit by lifting it by its If the vehicle is parked on handles;...
Page 236 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 237 TYRE PRESSURE KIT (2/3) With the engine running and the – after a maximum of 10 minutes, stop parking brake applied, inflating and read the pressure (on pressure gauge 1). – Unscrew the cap from recess 3 on the bottle; Note: while the container is empty- ing (approximately 30 seconds), the –...
Page 238 TYRE PRESSURE KIT (3/3) Precautions when using the – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – Put the kit away. than 10 consecutive minutes. –...
Page 239: Tools
TOOLS Jack 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned). Lever 3 This tightens or releases the tow eye 5. Hubcap tool 4 This tool is used to remove the wheel trims.
Page 240: Wheel Trims - Wheel
WHEEL TRIMS - WHEEL Remove the wheel trim using hubcap tool 1 (located in the tool kit) by en- gaging the hook in the opening near valve 2. To refit it, align it with valve 2. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve.
Page 241: Changing A Wheel
CHANGING A WHEEL (1/2) Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with the jack head). If the vehicle is not equipped with a jack or wheelbrace, you can obtain these from your approved dealer.
Page 242 CHANGING A WHEEL (2/2) Turn it a few times to lift the wheel off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.
Page 243: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will tial to keep them in good condition. become visible 2: it is then necessary You must make sure that your tyres to replace your tyres because the tread conform to local road traffic regulations.
Page 244 TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a In cases of under-inflation (puncture, the emergency spare wheel).
Page 245 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- For safety reasons, this op- sary to observe the speed specified by bidden.
Page 246 FRONT HEADLIGHTS: changing bulbs (1/3) After replacing the bulbs, you must put the air duct A back into position. To do this, perform the above operation in re- verse. Accessing the bulbs On the right-hand side of the vehicle, you will need to remove the filler neck 4 On the left-hand side of the vehicle, for the windscreen washer tank to you will need to remove the air duct A...
Page 247 FRONT HEADLIGHTS: changing bulbs (2/3) Halogen main beam headlight To change the bulb: – remove cover C; – turn the bulb holder a quarter turn 7; – remove the bulb. Bulb type: H7. It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights.
Page 248: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: changing bulbs (3/3) Front fog lights 10 Additional lights The front bumper needs to be removed; If you wish to fit fog lights to your ve- consult an approved Dealer. hicle, please see an authorised dealer. Bulb type: H8. LED dipped beam/main beam headlights 9 Please see an authorised dealer.
Page 249 REAR AND SIDE LIGHTS: changing bulbs (1/3) Side lights and brake lights Direction indicators 1 Refit the bulb holder and push the unit as far as it will go, until it locks into Consult an approved Dealer. Open the boot lid and remove screws 2. place.
Page 250 REAR AND SIDE LIGHTS: changing bulbs (2/3) Reversing lights Replace the bulb 5. Bulb type: H21W. From the boot, unclip the cover on the interior trim of the boot lid 4 using a Refitting screwdriver or similar tool. To refit, proceed in the reverse order, taking care not to damage the wiring.
Page 251 REAR AND SIDE LIGHTS: changing bulbs (3/3) High level brake light 6 Number plate lights 8 Side indicator lights 10 Consult an approved dealer. – Unclip the light 8 (using a tool such The wing mirror needs to be removed; as a flat-blade screwdriver).
Page 252: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs Map reading lights 1 Boot lights 2 Please consult an authorised dealer. Unclip light 2 by pressing the tabs on each side (using a flat-blade screw- driver or similar). Disconnect the light. Press tab 3 to release the lens 5 and access bulb 4.
Page 253: Renault Card: Battery
RENAULT unlock the vehicle (please refer to the Note: it is not advisable to touch the card: information on “Locking/unlocking the...
Page 254: Radio Frequency Remote Control Unit: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the battery Note: It is not advisable to touch the electronic circuit in the key cover when Open the case at slot 1 using a flat- replacing the battery. blade screwdriver or similar, and re- place the battery 2, observing the po- larity shown on the back of the cover.
Page 255: Fuses
FUSES (1/3) If any electrical component does not Fuses in passenger compartment C work, check the condition of the fuses. on the right-hand side of the vehicle Unclip the cover C using a screwdriver Fuses in passenger compartment or similar. A or B on the left-hand side of the vehicle Unclip the cover A using a screwdriver...
Page 256 FUSES (2/3) Use the fuse allocation label in the stor- age compartment A, B or C to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label.
Page 257 FUSES (3/3) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Indicators Steering column controls Brake light Heated seats ß ñ Audio amplifier Heated rear screen Door locking/unlocking Electric door mirror Wipers Accessories sockets ë...
Page 258: Battery
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 259 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 260: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only.
Page 261: Windscreen Wiper Blades
WINDSCREEN WIPER BLADES: replacement (1/2) Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the wind- screen wiper stalk to the stop position. The blade on the driver’s side must always be above the passenger blade.
Page 262 WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; –...
Page 263 Transport the vehicle on a trailer or tow RENAULT card on you, press the it with the front wheels off the ground. engine start button for 2 seconds. Reposition the lever to neutral (posi-...
Page 264 TOWING: breakdown recovery (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. – A vehicle must not be towed if it is not fit to be driven.
Page 265: Locking, Unlocking The Opening Elements
Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the in- formation on “Locking, unlocking the open-...
Page 266: Operating Faults
OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 267 Starting conditions are not Please refer to the information on “Starting, stopping fulfilled. the engine” in Section 2. The RENAULT card does Please refer to the information on “Starting, stopping not work. the engine” in Section 2. The engine cannot be switched off.
Page 268 OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 269 OPERATING FAULTS (5/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
Page 270 OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
Page 271 OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights. Traces of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the...
Page 272 5.40...
Page 273: Technical Specifications
Section 6: Technical specifications Vehicle identification plate ............Engine identification plate .
Page 274: Vehicle Identification Plate
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised hicle identification plate should be Mass). quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible The presence and location of the in- Weight) for front axle.
Page 275: Engine Identification Plate
ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 276: Dimensions
DIMENSIONS (in metres) 0,899 2,647 0,903 1,561 4,449 1,607-1,621* 1,560 2,058 * Unladen, with or without longitudinal roof bar...
Page 277: Engine Specifications
ENGINE SPECIFICATIONS Versions 1.2 TCe 1.5 dCi 1.6 dCi Engine type H5F turbo (see engine plate) Cubic capacity (cc) 1 197 1461 1 598 Type of fuel It is essential that you use unleaded petrol of the Octane rating octane rating stated on the label inside the fuel filler flap.
Page 278: Towing Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMTA) the information on “Vehicle identification plates”...
Page 279: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 280: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 281 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 282 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 283 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 284 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 285 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 286: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
Page 287 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 288 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 289 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 290 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 291: Alphabetical Index
ALPHABETICAL INDEX (1/5) brake fluid ................4.8 ABS ..............1.56, 2.29 → 2.38 bulbs accessories................ 5.28 changing ............5.14 → 5.20 accessories socket ............3.23 additional methods of restraint .......... 1.33 catalytic converter........... 2.12 – 2.13 side protection ............. 1.32 central door locking ....1.2 – 1.3, 1.5, 1.8 → 1.15, 1.18 to the front seat belts ........1.27 →...
Page 292 ALPHABETICAL INDEX (2/5) dimensions ................6.4 dipstick................. 4.4 4 wheel drive (4WD) ..........2.39 → 2.42 display ..............1.54 → 1.61 faults doors/tailgate ............1.4, 1.6 → 1.18 operating faults ..........5.33 → 5.39 driver’s position .............1.50 → 1.59 filter driving ..2.2 → 2.7, 2.12 – 2.13, 2.16 → 2.23, 2.29 → 2.42, air filter ................
Page 293 ALPHABETICAL INDEX (3/5) hazard warning lights signal ..........1.84 coolant ................4.7 headlight beam adjustment ........1.85 – 1.86 windscreen washer reservoir ......... 4.9 headrest..............1.19, 3.24 lifting the vehicle heated seats ..............1.20 changing a wheel ..........5.9 – 5.10 heated windscreen ..........3.7 →...
Page 294 ............... 5.22 sun visor ................3.18 remote control door locking unit ........1.2 → 1.4 switching on the vehicle ignition ......2.3, 2.5 → 2.7 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.18 RENAULT card battery ................5.21 tailgate ............3.27, 3.29 → 3.31...
Page 295 ALPHABETICAL INDEX (5/5) tanks and reservoirs vehicle identification plates ..........6.3 brake fluid ..............4.8 ventilation ..............3.2 → 3.13 coolant ................4.7 tanks and reservoirs: warning lights............1.54 → 1.71 windscreen washer ............4.9 washing ..............4.14 – 4.15 technical specifications ..........6.4 → 6.7 weights ................
Page 298 à999105663Rù ê ë ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault Kadjar Driver's Handbook Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Quick Links

Chapters

Related Manuals for Renault Kadjar

Summary of Contents for Renault Kadjar

Table of Contents