Dvd Player With Component Video; Computer With A Pc Monitor Output - Mitsubishi WD-52525 Owner's Manual

Connecting a DVD Player with Component Video or

Computer with a PC Monitor Output

DVD Player with Component Video

Figure 9
Component video cables and audio cables are required.
These are not included with the TV.
1. Connect the Component Video cables from Y/Pr/
Pb VIDEO OUT on the back of the DVD player to
COMPONENT-1 on the TV back panel, matching
the correct connection:
• Y to Y (Green)
• Pr to Pr (Red)
• Pb to Pb (Blue)
2. Connect a set of audio cables from AUDIO OUT
on the back of the DVD player to COMPONENT-1
AUDIO Input on the TV back panel. The red cable
connects to the R (right) channel, and the white
cable connects to the L (left) channel.
TV back panel
IR EMITTER
NetCommand
DVI
L
Analog Audio
R
HDMI
M-LINK
M-LINK
CONTROL/
RS-232C
DVD back panel
1.
Y V I D E O
C B
S
C
R
V I D E O O U T
Figure 9. Connecting a DVD Player with Component
Video
Note: NetCommand® will assume you
connected your DVD player to Component-1. If
you add a second DVD or use any other inputs
for your DVD, this change must match in the
NetCommand system. See Edit NetCommand...
in Chapter 3 for more information.
See Appendix B for component video
signal compatibility information.
For digital audio connections, see your
DVD Owner's Guides.
IEEE1394
INPUT/OUTPUT
2.
PC
VGA/SVGA/XGA/
R
720p
AUDIO
60 Hz MONITOR
VIDEO S-VIDEO
R L(MONO) OUTPUT
L
Red White
AUDIO 2
R
ANT-2
AUX AUDIO/VIDEO 1
PC-
AUDIO
DTV/
CABLE/
INPUT-1
VHF/
UHF
ANT-1 INPUT-2
PC-
MAIN INPUT
COMPONENT-1
YPbPr (480i/480p/720p/1080i)
DIGITAL COMPONENT-2
YPbPr (480i/480p/720p/1080i)
AUDIO
INPUT-DTV
YPbPr / RGB HV
(480i/480p/720p/1080i)
1.
CARD Pr/R Pb/B Y/G
TOP
V H
A U D I O O U T
M I T S U B I S H I A C I N
5 . 1 C H S U R R O U N D 2 C H B I T S T R E A M / P C M
White
D V D P L A Y E R
D D - 5 0 0 0
C E N T E R M O D E L
P O W E R S U P P L Y 1 2 0 V ~ 6 0 H z
L
P O W E R C O N S U M P T I O N 2 0 W
S E R I A L N O .
M A N U F A C T U R E D Red 2.
R D I S T R I B U T E D B Y
M I T S U B I S H I D I G I T A L E L E C T R O N I C S
A M E R I C A , I N C .
S U B W O O F E R S U R R O U N D F R O N T C O A X I A L O P T I C A L 9 3 5 1 J E R O N I M O R O A D Red
I R V I N E , C A 9 2 6 1 8
M A D E I N J A P A N
IMPORTANT

Computer with a PC Monitor Output

Figure 10
1. Connect PC Monitor Out from the computer to PC
Input on the TV back panel using a PC compatible
monitor cable. See Appendix B for PC signal
compatibility.
2. Connect the L (left) and R (right) audio cables from
the computer to PC AUDIO on the TV back panel.
In cases where your computer's audio output is a
single mini-jack, a splitter is needed to complete
this connection.
Note: To utilize the benefits of a digital A/V
receiver, connect your computer's digital audio
out, if available, to a digital input on your digital
A/V receiver.
TV back panel (section detail)
IEEE1394
INPUT/OUTPUT
PC
IR EMITTER
VGA/SVGA/XGA/
NetCommand
R
720p
60 Hz
L
DVI
L
Analog Audio
R
R
ANT-2
AUX
PC-
AUDIO
DTV/
CABLE/
VHF/
UHF
HDMI ANT-1
PC-
M-LINK MAIN
INPUT
M-LINK
CONTROL/
RS-232C
DIGITAL
AUDIO
1.
CARD
TOP
Computer with Monitor Output
Figure 10. Connecting a Computer with a PC Monitor
CAUTION: To ensure continued FCC
compliance, the user must use a shielded
video interface cable with bonded ferrite
cores at both ends when using the PC
input.
23