Mitsubishi WD-52528 Owner's Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Manuals
  4. Projection TV
  5. WD-52528
  6. Owner's manual

Mitsubishi WD-52528 Owner's Manual

Mitsubishi electronics wd-52528 projection television user manual
Hide thumbs Also See for WD-52528:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Training Manual
Owner's Guide
Projection Television Models
WD-52527, WD-62527
WD-52528, WD-62528
TM
TM
TM
Visit our website site at
www.mitsubishi-tv.com
TV Information:
Use this space to record the model and serial numbers of
your television. This information is on the back of your TV.
Model number
Serial number

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi WD-52528

Summary of Contents for Mitsubishi WD-52528

  • Page 1 Owner’s Guide Projection Television Models WD-52527, WD-62527 WD-52528, WD-62528 Visit our website site at www.mitsubishi-tv.com TV Information: Use this space to record the model and serial numbers of your television. This information is on the back of your TV. Model number...

  • Page 2: Lamp Replacement

    Custom cabinet installation must allow for proper air circulation around the television. STAND REQUIREMENT CAUTION: Mitsubishi TV models WD-52527 and WD-52528 are for use only with Mitsubishi stand models MB-52527 or MB-52528. Mitsubishi TV models WD-62527 and WD-62528 are for use only with Mitsubishi stand models MB-62527 or MB-62528.
  • Page 3 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4: Important Safeguards

    IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference.

  • Page 5: Replacement Parts

    IMPORTANT SAFEGUARDS 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

  • Page 6: Table Of Contents

    Chapter 1: Television Overview Special Features ... 10 TV Accessories ... 11 Remote Control Functions: Overview ... 12 Remote Control Functions: Operation ... 13 Care ... 14 Sleep Timer ... 14 Front Control Panel ... 15 Front Panel Indicator Lights ... 16 Back Panel ...

  • Page 7: Controlled Recordings

    Chapter  : IEEE 139 Devices and NetCommand® Controlled Recordings IEEE 1394 Devices and NetCommand® Control ... 52 Adding IEEE 1394 Devices Automatically ... 53 Device Selection Menu ... 55 Using the Device Menu Button to Display Menus ... 56 Using the GUIDE Button to Display ChannelView and Menus ...

  • Page 8: Our Thanks

    Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider. This Owner’s Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner’s Guide to become familiar with the innovative features and operations this unique television offers.
  • Page 9 Television Overview Special Features ... 10 TV Accessories ... 11 Remote Control Functions: Overview ... 12 Remote Control Functions: Operation ... 13 Care ... 1 Sleep Timer ... 1 Front Control Panel ... 15 Front Panel Indicator Lights ... 16 Back Panel ...

  • Page 10: Chapter 1: Television Overview

    Special Features Your new High Definition widescreen television has many special features that make it the perfect center of your home entertainment system, including: Digital Cable Ready (CableCARD™) Your widescreen Mitsubishi HDTV is “Plug-and-Play” ready. It can descramble a cable provider’s one-way digital signals with the use of a CableCARD security module.

  • Page 11: Tv Accessories

    5. Owner’s Guide (not pictured) 6. TV Guide On Screen® User’s Manual (not pictured) 7. Quick Reference Card (not pictured) For the WD-52528 or WD-62528 1. Remote Control 2. Two AA Batteries 3. One Quadruple IR Emitter Cable (allows NetCommand to control other devices) 4.

  • Page 12: Remote Control Functions: Overview

    TV Guide On Screen system. See Appendix D for details. Chapter 1. Television Overview Light: Located on the left side for WD-52527 and WD-62527 and on the right side for WD-52528 and WD-62528 of the remote control, this feature illuminates buttons or labels.

  • Page 13: Remote Control Functions: Operation

    2. Load the batteries, making sure the polarities (+) and (-) are correct. For best results, insert the negative (-) side first. AAA batteries are used with the WD-52527 and WD-62527. AA batteries are used with WD-52528 and WD-62528. WD-52528 & WD-62528 Remote Operation: Installing the Batteries Chapter 1.

  • Page 14: Care

    Remote Control Functions: Care and Sleep Timer Sleep Timer Setting the Sleep Timer: 1. Press SLEEP on the remote control. 2. Each press of SLEEP increases the time displayed by 30 minutes, until the maximum value of 120 minutes is reached.

  • Page 15: Front Control Panel

    Front Control Panel The buttons on the Front Control Panel highlighted are duplicated on the remote control. The top row of labels shows the control functions when there are no TV menus displayed on the screen. The bottom row of labels shows the control functions when the TV menus are displayed on the screen or when a special function has been activated.

  • Page 16: Front Panel Indicator Lights

    Front-Panel Indicator Lights POWER SYSTEM RESET LAMP STATUS TIMER Indicators Refer to the following tables for explanations of the front-panel indicator lights. Power/Timer Indicator Indicator Color TV Condition None (indicator off) TV is powered OFF. Green, steady TV is powered ON. Green, rapid blinking 1.
  • Page 17 Front-Panel Indicator Lights, continued Status Indicator Indicator Color TV Condition None (indicator off) Normal TV on or standby condition. Yellow, steady 1. Operating temperature is too high, dust filter may need cleaning. 2. Room temperature is too high. Yellow, blinking Dust filter cover is not in place or not secure.

  • Page 18: Back Panel

    They cannot both be connected at the same time. . Component-1, -2 Inputs YPbPr Component-3 is available on WD-52528 and WD-62628. These inputs can be used for the connection of devices with component video outputs, such as a DVD player, external HDTV receiver or compatible video game system.

  • Page 19: Service Port

    Analog Audio OUTPUT OUTPUT VIDEO AUDIO- LEFT/ (MONO) AUDIO- LEFT/ (MONO) AUDIO- RIGHT AUDIO- RIGHT MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR SERVICE PORT CableCARD™ ANT 1 CARD TOP USE WITH IEEE 1394 INPUT/ OUTPUT WD-52528 WD-62528 Chapter 1. Television Overview...

  • Page 20: Digital Audio Output

    Back Panel, continued 9. DTV Link/IEEE 139 These jacks allow the TV to connect to external IEEE 1394 digital products by means of a single cable. Two jacks are provided for this purpose, allowing for a high degree of flexibility in connecting your Detailed information regarding IEEE 1394 connection requirements are in Chapter 4.
  • Page 21 Chapter . . . Connecting External Devices & NetCommand® Setup ... 22 Wall Outlet Cable or Cable Box ... 23 CableCARD™ Technology ... 2 Antenna with Single Lead ... 25 Antennas with Separate UHF and VHF Leads ... 25 VCR to an Antenna or Wall Outlet Cable... 26 VCR Video and Audio to TV ...

  • Page 22: Chapter 2: Connecting

    Connecting External Devices and NetCommand NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory.

  • Page 23: Wall Outlet Cable Or Cable Box

    Connecting a Wall Outlet Cable or Cable Box Wall Outlet Cable (can be used with a CableCARD™) Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use. 1. Connect the primary incoming coaxial lead cable to ANT-1 MAIN on the TV back panel.

  • Page 24: Cablecard™ Technology

    CableCARD™ Technology CableCARD Technology CableCARD is a nationwide system standard that allows your local cable TV provider to supply you with an access card customized to your account. This card allows your TV to receive, decode and unscramble the premium digital channels included in your cable TV subscription, without the use of a cable box.

  • Page 25: Antenna With Single Lead

    Connecting an Antenna with a Single Lead or Antennas with Separate UHF and VHF Leads Antenna with Single Lead (not for use with CableCARD™) Figure 3 A 300-Ohm to 75-Ohm transformer is required. This is not included with the TV, but is available at most electronics stores. For antennas with flat twin leads 1.

  • Page 26: Vcr To An Antenna Or Wall Outlet Cable

    Connecting a VCR to Antenna or Wall Outlet Cable Connecting VCR Video and Audio to the TV Connecting VCR to an Antenna or Wall Outlet Cable and Connecting VCR Video and Audio to the TV Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables and an S-Video or Video cables are required.

  • Page 27: Vcr Video And Audio To A Cable Box

    Connecting VCR Video and Audio to a Cable Box VCR Video and Audio to a Cable Box Figure 6 A two-way RF splitter, 4 coaxial cables, right and left audio cables and an S-Video or Video cable are required. These are not included with the TV.

  • Page 28: A/V Receiver

    Connecting an A/V Receiver (Stereo System) Connecting a Satellite Receiver or Other Device with S -Video A/V Receiver (Stereo System) Figure 7 A coaxial digital audio cable or stereo audio cables are required. These cables are not provided with the TV. •...

  • Page 29: Dvd Player With Component Video

    Connecting a DVD Player with Component Video Connecting an HDTV Cable Box or Satellite Receiver with Component Video DVD Player with Component Video Figure 9 Component video cables and audio cables are required. These are not included with the TV. 1.

  • Page 30: Hdmi Device

    Connecting an HDMI or DVI Device HDMI Device Figure 11 An HDMI-to- HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer. You can connect two HDMI devices to the TV back panel through the HDMI connections.

  • Page 31: Ir Emitter Netcommand

    A double IR Emitter cable is included with models WD-52527 and WD-62527. A Quadruple IR Emitter cable is included with models WD-52528 and WD-62528. The emitters connected to these jacks are used by the NetCommand system to control other devices such as VCRs, DVD players, Cable boxes and Satellite receivers.

  • Page 32: Compatible Ieee 1394 Devices

    Connecting Compatible IEEE 139 Devices Compatible IEEE 139 Devices It is possible to connect devices to the TV that have IEEE 1394 connectors but are not compatible with the TV or with the NetCommand ® control system. Areas of compatibility to consider are: 1.
  • Page 33 Connecting Compatible IEEE 139 Devices, continued Connection Styles There are two different connection styles that can be used when connecting IEEE 1394 devices. Use the style that fits your network of audio/video products. Direct Device-To-Device Style The IEEE 1394 offers you the capability to chain devices, unlike previous audio and video connections where you had to individually connect each device directly to the TV.

  • Page 34: Helpful Hints

    Connecting: Helpful Hints Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s audio to both the TV and the A/V Receiver? A. Connect the single set of stereo audio outputs to the TV only. Use Edit NetCommand® to change the setup of this device.
  • Page 35 NetCommand ® Setup and Editing NetCommand® Introduction ... 36 Using the Remote Control with NetCommand® ... 37 NetCommand® Setup On-Screen Buttons ... 38 3D Graphical Viewpoint® Menu System ... 39 NetCommand® Initial Setup ... 0 Edit NetCommand® Add an A/V Receiver ... 3 Add Devices ...

  • Page 36: Chapter 3. Netcommand Setup And Editing

    NetCommand® Introduction Welcome To NetCommand! NetCommand makes your TV the heart of your Home Theater NetCommand® is an intelligent control system that allows your Mitsubishi TV to become the heart of your Home Theater. With NetCommand, the TV sends signals to the other devices in the system, telling them to play, record, change inputs, adjust volume, change channels and many more functions.

  • Page 37: Using The Remote Control With Netcommand

    Using the Remote Control with NetCommand Below is a list of several manufacturers’ devices tested and shown to be compatible with NetCommand. These devices can be controlled without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models since many manufacturers use the same control signals to operate some or all of the models they offer.

  • Page 38: Netcommand® Setup On-Screen Buttons

    NetCommand® Setup On-Screen Buttons To use the TV’s NetCommand feature, you need to provide some detailed information during the setup of your Mitsubishi TV. You must define the manufacturer of the devices that are connected to the television, or learn the IR code remote control signals for the device connected.

  • Page 39: Graphical Viewpoint® Menu System

    3D Graphical Your TV also has Mitsubishi’s exclusive 3D Graphical information for menu choices and changes using the Menu Screens A picture (icon) will be highlighted on the menu screen when selected with the ADJUST arrows. You may then make changes within the menu or access sub-menus, if available.

  • Page 40: Netcommand® Initial Setup

    NetCommand Initial Setup ® IMPORTANT You may use your TV without setting up NetCommand or the TV Guide On Screen® system. To set up at a later time, choose the NetCommand menu from the Main menu, then select Initial. The TV Guide On Screen system is set up from the NetCommand menu.

  • Page 41: Device Setup Screen

    NetCommand ® Initial Setup, continued Device Setup Screen Figure 3 If the devices connected to the TV are already in NetCommand memory, you can quickly select them at this screen. Press ADJUST device type. Press ADJUST manufacturer. Select “Other” if the manufacturer is not listed.

  • Page 42: Review Screen

    NetCommand ® Initial Setup, continued Review Screen Figure 5 After you have made your device choices the Review Screen will display. It is important to review the settings to ensure that they are correct. If necessary, you can use <Back to return to the Device Setup screen to make changes.

  • Page 43: Edit Netcommand® Add An A/V Receiver

    Edit NetCommand®, Add an A/V Receiver A/V Receiver Screen Figure 7 If your A/V Receiver manufacturer was not listed, and you selected “None” during the initial NetCommand setup, you may add the A/V Receiver and have NetCommand learn its remote control’s functions. Either select Edit from the Finish screen or, if you have finished the initial setup, go to the Main menu, select NetCommand, then press ENTER.
  • Page 44 Edit NetCommand A/V Receiver (AVR) Input Learn Screen Figure 9 NetCommand can now learn the remote control signals used to select each input on the A/V receiver. 1. Press ADJUST on the TV remote to select the check box for each function to be learned.
  • Page 45 Edit NetCommand Name Screen Figure 11 The Name screen allows you to change the default name for the A/V receiver to a custom name of up to eight characters (including a blank space), selecting from letters, numbers, and nine different characters. Using the TV’s remote, press ADJUST letter, then press ENTER to move to the next position.

  • Page 46: Add Devices

    Edit NetCommand Mitsubishi’s NetCommand allows you to edit your home theater configuration. You can add new devices, change device settings and connections, delete devices and learn remote control IR signals not already in NetCommand memory. Edit NetCommand Screen Figure 14 If you selected Edit when you were at the Finish screen, the Edit NetCommand screen displays.
  • Page 47 Edit NetCommand [Device] Screen Figure 16 If you selected “None”, during initial setup, then you can add a device. If you have added a new device, use this screen to start learning. Our examples show the choices for adding a VCR, however, the same type of screens will appear for any DBS (Direct Broadcast Satellite), DVD player or Cable Box.
  • Page 48 Edit NetCommand®, Add Devices, continued Figure 17. [Device] Learn screen [Device] Advanced Learn Screen Figure 18 After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand.

  • Page 49: Vcr For Recordings Screen

    Edit NetCommand The screens described below may not be necessary for your device setup. If they do not display automatically on screen, they are not required. VCR for Recordings Screen Figure 21 Select the VCR to use for making analog recordings through NetCommand or the TV Guide On Screen®...

  • Page 50: Change Devices

    Edit NetCommand Change Device Screen Figure 24 Selecting Change from the Setup menu screen, displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V receiver. If “Other” was selected for the manufacturer then you can also “Learn”.
  • Page 51 Chapter . . . IEEE 139 Devices and NetCommand® Controlled Recordings IEEE 139 Devices and NetCommand® Control ... 52 Adding IEEE 139 Devices Automatically ... 53 Device Selection Menu ... 55 Using the Device Menu Button to Display Menus ... 56 Using the GUIDE Button to Display ChannelView and Menus ...

  • Page 52: Chapter  : Ieee 139 Devices And Netcommand® Controlled Recordings

    IEEE 139 Devices and NetCommand® Control See pages 32 and 33 for information regarding compatible IEEE 1394 devices and connection styles. The TV is not able to control IEEE 1394 devices that use other types of control protocols. Incompatible digital audio, video and/or control information will still be able to pass from one device through the TV to another device on the network.

  • Page 53: Adding Ieee 1394 Devices Automatically

    Adding IEEE 139 Devices Automatically Adding IEEE 139 Devices Automatically When an IEEE 1394 device is connected into the TV network and is powered On, the new device will automatically announce its presence. This process is called device discovery and can take up to 1 minute. Some non-audio/video or non-compatible IEEE 1394 devices, such as Personal Computers (PCs), may not announce their presence to the TV.

  • Page 54: Connection Screen

    Adding IEEE 139 Devices Automatically, continued IEEE 139 Device Type Screen Figures 3 and 4 If the new IEEE 1394 device is also connected using analog inputs, you will need to define the device type. Select the type of device, such as a VCR or cable box. Figure 3.

  • Page 55: Device Selection Menu

    Device Selection Menu When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 7) displays. If NetCommand® has not been set up, the Device Selection menu allows you to select an input for viewing. If NetCommand is set up, the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V receiver, power compatible devices On or Off, and verify the destination of signals.

  • Page 56: Using The Device Menu Button To Display Menus

    Using the Device Menu Button to Display Menus Device Menu Pressing the remote control’s DEVICE MENU button displays the menu for the current device source. IR Controlled Devices For a NetCommand compatible traditional IR controlled device, pressing DEVICE MENU once or twice will display the menu for that device.

  • Page 57: Using The Guide Button To Display Channelview

    Using the GUIDE Button to Display ChannelView™ and Menus The GUIDE Button Please refer to the separate TV Guide On Screen® Interactive Program Guide User’s Manual for details about using the GUIDE button with TV Guide On Screen. When you are not using the GUIDE key for the TV Guide screens, pressing GUIDE allows you to see NetCommand®...

  • Page 58: Netcommand® Controlled Peer-To-Peer Connections

    ® NetCommand Controlled Peer-to-Peer Connections What is a Peer-to-Peer Connection? Figure 12 A peer-to-peer connection allows the IEEE 1394 devices in your TV network to talk to each other without the further need of TV intervention once the peer-to-peer connection is established. For example, the TV can set up a connection for an IEEE 1394 cable box that sends a program to be recorded to an A/V Disc or DVCR.

  • Page 59: Direct Vcr Recording From An Antenna Or Cable Source

    Direct VCR Recording from an Antenna or Cable Source, A/V Disc Search, Track List Screen Direct VCR Recording from an Antenna or Cable Source: Pressing REC (record) on the TV’s remote control will function the same way as pressing the record button on the VCR’s remote control or front panel.
  • Page 61 Chapter . . . TV Menu Screen Operations Main Menu Choices ...62 Setup Menu ...63 NetCommand® Menu ...65 Record Menu ...66 Channel Menu ...68 Captions Menu ...70 V-Chip Lock Menu ...72 Audio/Video Menu ...75 A/V Settings Descriptions ...76 Operation of PIP and POP ...78...

  • Page 62: Chapter 5: Tv Menu Screen Operations

    Main Menu Choices Setup Menu Figure 1 Use the Setup menu to select English or Spanish as the language for the menus and on-screen displays. Manually set the time for the TV, or select Auto and the TV will automatically set the time based upon Extended Data Service (XDS) time data.

  • Page 63: Setup Menu

    Setup Menu Setup Menu Figure 8 Figure 8. Setup Menu Language Display the on-screen menus in either English or Spanish (Español). The first time you powered On your TV, you were requested to select an on-screen menu language. If you choose to change the selection, all menu text will immediately switch to the language of your choice.

  • Page 64: Software Version

    Time Zone Select your correct time zone. Press ADJUST select the time zone (Atlantic, Eastern, Central, Mountain, Pacific, Alaska or Hawaii) for your area. Then press ADJUST to move to the Daylight Savings time option. Daylight Savings Time Select the Daylight Savings time (DST) option that your state uses.

  • Page 65: Netcommand® Menu

    NetCommand® Menu NetCommand Menu Figure 11 Figure 11. NetCommand Menu Edit Detailed information regarding setting up and editing the NetCommand system is found in Chapter 3. The Edit NetCommand screens allow you to add new devices and change traditional and IEEE 1394 devices. You can also set up the TV Guide On Screen®...

  • Page 66: Record Menu

    Record Menu Record Figure 14 The Record menu allows you to manually set up recordings, view the record list, and set defaults for your recording devices. Figure 14. Record Menu Recording Setup Figure 15 Figure 15. Recording Setup screen The recording Setup menu is where you tell the TV what, where, and when to record.

  • Page 67: Record List

    Record Menu, continued Record List Figure 16 A maximum of 32 recordings can be scheduled. To cancel a recording on the Record List, press ADJUST to select the recording, then press CANCEL. To page through the list, press CH scheduled from the ChannelView™ screen appear on this list.

  • Page 68: Channel Menu

    Channel Menu Channel Figure 17 Figure 17. Channel Menu Antenna Select the antenna for the channels you want to edit. You can select Ant-1 (main) or Ant-2 (Aux). Prefer Digital When a memorized channel is available with the same main channel number in both analog and digital formats, a check mark in the Prefer Digital box will allow digital channels to display and analog channels to be hidden (when using CH...

  • Page 69: Superquickview

    SQV (SuperQuickView™) SQV (SuperQuickView™) Using The Menu Screen Figure 17 SQV (SuperQuickView™) allows you to put together lists of your favorite channels from Antenna 1 and Antenna 2. You can store channels in any of the 9 different SQV memory banks. You can also store the same channel in multiple memory banks.

  • Page 70: Captions Menu

    Captions Menu: Analog and Digital Captions Captions Menu Figure 18 For analog channels broadcasters can send either Standard or Text closed captioning. Standard Closed Captions follows the dialogue of the characters on- screen and displays in a small section of the screen. Text Closed Captions often contain information such as weather or news and covers a large portion of the screen.

  • Page 71: Background Opacity

    Captions Menu, continued: Customizing Digital Settings Fonts You can customize the text of digital captions by selecting the font of your choice. The available Font options are as follows: • Default - Selected by the Closed Captions provider • Font 1 - Monospaced font with Serifs •...

  • Page 72: V-Chip Lock Menu

    V-Chip Lock Menu: Pass Code V-Chip Select V-Chip Lock to perform the functions listed below. V-Chip allows you to Block or Allow programs based upon rating signals sent by the broadcaster. The TV comes from the factory with the V-Chip Lock in the Off setting.
  • Page 73 V-Chip Lock Menu: V-Chip Definitions V-Chip Signal Information When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the INFO button on the remote control.

  • Page 74: Lock By Time

    V-Chip Lock Menu, continued Lock By Time Figure 23 Lock by Time allows you to lock the entire TV during specific hours. During the Lock Time, you must use your pass code to view the TV. To enable the lock: Press ADJUST to select On or Off, then press ADJUST...

  • Page 75: Audio/Video Menu

    Audio/Video Menu Audio/Video Figure 24 Figure 24. Audio/Video Menu, Settings A/V Memory Reset A/V Memory Reset allows you to select the device/input which will have the A/V Settings returned to the original factory settings. To return a device’s memory to the original factory settings, select the device and then press ENTER.

  • Page 76: A/V Settings Descriptions

    A/V Setting Descriptions: Audio NOTE: The effects of the Audio Settings of Bass, Treble, Balance and Surround affect the sound heard through the TV speakers only. Analog and Digital Audio Setting A slider will display on screen for most settings. When the slider is displayed it has a numeric value, where 63 is the maximum, 31 is the mid-point and 0 is the minimum.

  • Page 77: Video Settings

    CANCEL. ◊ DeepField™ Imager (WD-52528 and WD-62528) When On is selected, the black levels are dynamically enhanced in portions of the screen to provide strong contrast with detail over mixed screen content.

  • Page 78: Operation Of Pip And Pop

    Ant-1 or a cable box. Exchanging Program Images Press ENTER/EXCH (WD-52527, WD-62527) or EXCH (WD-52528, WD-62528) to exchange the main picture and the PIP/POP picture. Pictures from digital channels can only be shown as the main picture. Moving PIP Image...
  • Page 79 Chapter . . . Special Features TV Display Formats ... 80 Display Formats ... 81 Device Control with NetCommand® ... 82 Appendix A: Bypassing the V-Chip Lock ... 85 Appendix B: Specifications ... 87 Appendix C: Remote Control Programming Codes ... 89 Appendix D: On-Screen Information Displays ...

  • Page 80: Chapter 6: Special Features

    TV Display Formats This is a widescreen TV (also known as a 16:9 TV). This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats to choose from.

  • Page 81: Display Formats

    TV Display Formats Chapter 6. Special Features...

  • Page 82: Device Control With Netcommand

    Device Control with Net Command NetCommand Compatible Traditional Devices (Analog) When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) A/V RECEIVER Device Remote Control Button POWER Power On/Off (toggle) GUIDE Changes between digital and analog audio FORMAT When Net Command®...
  • Page 83 Device Control with Net Command When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) TUNER/ Device CABLE BOX/ Remote Control Button POWER Power On/Off (toggle) GUIDE FORMAT When an IEEE 139 Device is Viewed or Played CABLE/DBS Device Remote...
  • Page 84 Chapter 6. Special Features...

  • Page 85: Appendix A: Bypassing The V-Chip Lock

    Appendix A: Bypassing the V-Chip Lock: Bypassing the V-Chip Lock After you set the lock, you need your pass code to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip Lock menus. If you forget your pass code, you can view the locked TV without entering your pass code.
  • Page 86 This page intentionally blank Chapter 6. Special Features...

  • Page 87: Appendix B: Specifications

    HDMI (digital video/audio): Qty. 2 Signal Type Video/S-Video: Qty. 3 each Signal Type Component Video (Y/Pr/Pb) WD-52527, WD-62527: Qty. 2 sets WD-52528, WD-62528: Qty. 3 sets Signal Type Audio Inputs: WD-52527, WD-62527: Qty. 7 pairs WD-52528, WD-62528: Qty. 8 pairs Outputs Video Record Video: Qty.
  • Page 88 Digital Audio Output: Qty. 1 IEEE 139: Qty. 2 Audio/Speakers Dimensions WD-52527, WD-52528 WD-62527, WD-62528 Power Consumption Net command® IEEE 139 System Compatibility: This television is designed to conform to IEEE 139 AV/C Software standards in effect at the time of development. This exciting new networking and control technology is designed to provide high-performance digital connections and product control, making the product easier to use.

  • Page 89: Appendix C: Remote Control Programming Codes

    Appendix C: Remote Control Programming Codes IMPORTANT The remote control may return to its initial setting when the batteries are changed. You may need to reprogram. Programming the Remote to Control NetCommand A/V Products 1. Move the slide switch at the top of the remote to the TV position.
  • Page 90 Appendix C: Remote Control Programming Codes, continued Cable Boxes, continued SCIENTIFIC ATLANTA 112, 113, 194 SIGNATURE 119,124,125,126,127,120,121,122 SLMARK 105,101 SPRUCER STARCOM 119,124,125,126,127,120,121,122 STARGATE TELEVIEW 101,105 TOCOM 135,136 TOSHIBA UNIKA UNITED CABLE 119,124,125,126,127,120,121,122 UNIVERSAL VIDEOWAY VIEWSTAR 129,130 ZENITH 117,100 DVD Players DVD Brand Code MITSUBISHI...
  • Page 91 Appendix C: Remote Control Programming Codes, continued IMPORTANT Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, your remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver.

  • Page 92: Appendix D: On-Screen Information Displays

    Appendix D: On-Screen Information Displays When you turn on the TV, change devices, change channels, or when you press the INFO button on the remote control, the TV will display the current status. The most common displays are shown below. Please note that seldom or never do all of the different status indicators appear at the same time.

  • Page 93: Appendix E: Netcommand® Specialized Device Keys

    Appendix E: NetCommand® Specialized Device Keys CABLE VCR DVD LEARNING SCREEN RECEIVER or DBS These are paired functions (e.g. Power and Power Off). When the original remote control uses a single button for both functions, learn only the first of the paired functions. †...

  • Page 94: Appendix F: Cleaning And Service

    Appendix F: Cleaning and Service Cleaning Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet. Top and Sides of the TV: •...

  • Page 95: Appendix G: Filter Cleaning

    Appendix G: Filter Cleaning Cleaning the Dust Filter Clean the filter annually and whenever you replace the lamp cartridge. Tool needed: Phillips screwdriver 1. Turn the television off and unplug the AC cord. 2. Carefully access the back of the television. If the TV must be moved, use two people.

  • Page 96: Appendix H: Lamp Cartridge Replacement

    Appendix H: Lamp Cartridge Replacement Before you replace the lamp cartridge please note the following: CAUTION: If the television is on, press POWER to turn it off. Allow the television to cool for one hour before attempting to replace the lamp cartridge. LAMP LIFE The light source for this television is a lamp, which is part of a lamp cartridge assembly.
  • Page 97 Appendix H: Lamp Cartridge Replacement, continued To order a new lamp under warranty, call (800) 332-2119. Please have model number, serial number and TV purchase date available. To order a new lamp after warranty, call (800) 553-7278 and order lamp part number 915P028010. Chapter 6.

  • Page 98: Troubleshooting

    Troubleshooting Problem The TV remote control does not work. The TV takes several seconds to respond. Cable provider needs information to start CableCARD™ service. You cannot access a channel. On-screen displays appear each time you change a function. You cannot program the TV to turn on automatically (timer function) There is no sound even when the volume is turned up.
  • Page 99 Troubleshooting, continued Problem The sound does not match the screen picture. There is a large black or gray rectangle on the screen. You cannot see a picture when playing a VHS tape. V-Chip is not working. The TV will not turn on after being plugged in. TV functions do not respond to the remote control or to front panel control and will not power off.
  • Page 100 Troubleshooting, continued Problem The A/V Receiver is the selected audio source but there is no sound. The TV Speaker icon or A/V Receiver icon is grayed out and not selectable. Cannot see the A/V Receiver menu. Screen is black when trying to view digital channels or IEEE 1394 device.
  • Page 101 Troubleshooting, continued Problem The IEEE 1394 Device is not listed in the Device Selection menu. The IEEE 1394 device cannot be selected. DEVICE MENU button does not display a menu. All IEEE 1394 devices disappear. Cannot rediscover a deleted IEEE 1394 device An IEEE 1394 device has been plugged in but does not appear in the Device Selection menu (not discovered).

  • Page 102: Demo Mode

    Troubleshooting, continued Problem Program to be recorded was correctly selected from ChannelView, however, incorrect program was recorded. Incomplete ChannelView program recorded. ChannelView program recording failed. TV Guide On Screen® system shows no program listings. TV Guide On Screen system program listings don’t match actual programs TV Guide On Screen system does not change channels on the cable box.

  • Page 103: Trademark And License Information

    Trademark and License Information LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

  • Page 104: Index

    Index A/V Disc Search 59 A/V Memory Reset 75 A/V Receiver Connecting 26 Inputs 43 Input Learn Screen 44 Learn Screen 44 Screen 43 A/V Setting Descriptions: Audio 76 A/V Setting Descriptions: Video 77 IEEE 1394 Devices Automatically 53 Devices 46 Screen 46 Advanced Learn Screen 48 Analog and Digital Audio Setting 76...
  • Page 105 Memorize 63 Memory 68 Name, Channel Menu 68 Name for 1394 Device Screen 53 Name Screen 45, 48 NetCommand® Home Network Control System 10 Initial Setup 40 Setup 22 Setup On-Screen Buttons 38 Specialized Device Keys 93 Information Screen 40 Menu 64, 67 New 1394 Device Screen 55 On-Screen Information Displays 92...

  • Page 106: Mitsubishi Tv Software

    MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.

  • Page 107: Warranty

    This LCD Projection Television uses three LCD panels to create the screen image. This technology creates the image using small dots, or picture elements (pixels). Your LCD Projection TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels.
  • Page 108 Mitsubishi LCD Rear Projection Television Limited Warranty (continued) This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs,...
  • Page 110 © 2005 Mitsubishi Digital Electronics America, Inc. 853B541A10 Website: www.mitsubishi-tv.com E-mail: MDEAservice@mdea.com To order replacement or additional remote controls, lamp cartridges or Owner’s Guides, call 800-553-7278 For questions, call Consumer Relations at 800-332-2119 Written and Printed in the U.S.A.

This manual is also suitable for:

Wd-62527Wd-62528Wd-52527

Table of Contents