A/V Receiver (Stereo Or Surround Sound Audio System); Dvd Player With Component Video - Mitsubishi WD-52526 Owner's Manual

A/V Receiver (Stereo or Surround
Sound Audio System)
Figure 9
Most setups require either a coaxial digital audio cable or
stereo audio cables. In some circumstances, you may need to
connect both digital audio and stereo audio.
A. To connect an analog A/V receiver:
Connect a set of stereo audio cables from AUDIO
OUTPUT on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. Connect the
red cable to the R (right) channel and the white cable
to the L (left) channel.
The TV converts digital audio from digital channels to
analog audio.
B. To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of a coaxial digital audio cable to
DIGITAL AUDIO on the back of the TV. Connect the
other end to the COAXIAL DIGITAL INPUT on the
back of the A/V receiver.
The TV converts analog audio from analog channels
or devices to PCM digital stereo audio.
COMPONENT COMPONENT
INPUT INPUT YPbPr (480i/480p/720p/1080i) YPbPr (480i/480p/720p/1080i)
1 1 2 2
1 1 2 2
Y Y
-VIDEO O -VIDEO
Pb Pb
Pr Pr
AUDIO- AUDIO-
LEFT/ LEFT/
LEFT/ LEFT/
(MONO) (MONO)
AUDIO- AUDIO-
RIGHT RIGHT
DTV/CABLE/
DTV DTV/CABLE/ T / V/ V CA TV C BLE/ CA
VHF/UHF VHF/UHF VHF/ F/ F UHF
DIGITAL DIGITA DIGITAL TA T L
AUDIO AUDIO AUDIO
OUTPUT OUTPUT OUTPUT
ANT 1 ANT 1 ANT 1
Figure 9. Connecting an A/V receiver
On rare occasions, an HDMI signal may be copy-
restricted and cannot be output from the TV as a digital
signal. To hear these copy-protected signals through the
A/V receiver, use connections for an analog A/V receiver.
INPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
DVI DVI AUDIO AUDIO AUDIO AUDIO AUDIO RECORD RECORD RECORD RECORD RECORD
Analog Audio Analog Audio OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
1 1 2 2
VIDEO VIDEO VIDEO
AUDIO- AUDIO- AUDIO- AUDIO- AUDIO-
LEFT/ LEFT/ LEFT/ LEFT/ LEFT/
(MONO) (MONO) (MONO) (MONO) (MONO)
AUDIO- AUDIO- AUDIO- AUDIO- AUDIO-
RIGHT RIGHT RIGHT RIGHT RIGHT
MONITORLINK™/HDMI MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR AUDIO PCM LINEAR
1 1 2 2
SERVICE SERVICE
PORT PORT
Chapter 2. Connecting
Check the A/V receiver's Owner's Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.

DVD Player with Component Video

Figure 10
Component video cables and audio cables are required. These
are not included with the TV.
1. Connect the Component Video cables from Y/Pr/Pb
VIDEO OUT on the back of the DVD player to a COM-
PONENT input on the TV back panel, matching the
correct connections:
• Y to Y (Green)
• Pr to Pr (Red)
• Pb to Pb (Blue)
2. Connect a set of audio cables from AUDIO OUT on
the back of the DVD player to the COMPONENT
AUDIO input on the TV back panel. Connect the red
cable to the R (right) channel, and the white cable to
the L (left) channel.
INPUT INPUT
1 1
S-VIDEO S-VIDEO O
VIDEO VIDEO
AUDIO- AUDIO-
LEFT/ LEFT/
(MONO) (MONO)
AUDIO- AUDIO-
RIGHT RIGHT
Figure 10. Connecting a DVD Player with Component
Video
See Appendix C for component video signal
compatibility information.
For digital audio connections to your
A/V receiver, see your DVD player and A/V
receiver Owner's Guides.
COMPONENT COMPONENT COMPONENT
YPbPr (480i/480p/720p/1080i) YPbPr (480i/480p/720p/1080i) YPbPr (480i/480p/720p/1080i)
1 1 1 2 2 2
2 2
Y Y Y
Pb Pb Pb
Pr Pr Pr
AUDIO- AUDIO- AUDIO-
LEFT/ LEFT/ LEFT/
(MONO) (MONO) (MONO)
AUDIO- AUDIO- AUDIO-
RIGHT RIGHT RIGHT
IMPORTANT
29