Caraudio-Systems c.LOGiC C2-RNSE Manual

For navigation systems audi navi plus rns-e

Advertisement

Quick Links

c.LOGiC-Interface
C2-RNSE
For navigation systems
Audi Navi Plus RNS-E
Only for vehicles WITHOUT factory rear-view camera
Product features
• full plug and play multimedia interface
• 2 AV-inputs with separate IR-control channel
• integrated into and controllable by vehicle infotainment
• control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, ...
• after-market rear-view camera input
• automatic switching to rear-view camera input (optional coding necessary to switch from
OEM-modes)
• rear-view camera power (+12V max 1A)
• rear-seat-entertainment AV-output
• power on remote out trigger signal (+12V max 1A) to switch on connected devices
• video-in-motion
Version 24.02.2012
C2-RNSE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the c.LOGiC C2-RNSE and is the answer not in the manual?

Questions and answers

Summary of Contents for Caraudio-Systems c.LOGiC C2-RNSE

  • Page 1 c.LOGiC-Interface C2-RNSE For navigation systems Audi Navi Plus RNS-E Only for vehicles WITHOUT factory rear-view camera Product features • full plug and play multimedia interface • 2 AV-inputs with separate IR-control channel • integrated into and controllable by vehicle infotainment •...
  • Page 2: Table Of Contents

    Contents 1. Prior to Installation 1.1. Delivery contents 1.2. Check compatibility of vehicle and accessories 1.3. Setting the dip switches of the CAN-box TV-400 1.4. Setting the dip switches of the Interface-box C2C-M200 1.4.1. Automatic switching to rear-view camera 1.4.2. Deactivating c.LOGiC AV2-input 2.
  • Page 3: Prior To Installation

    Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
  • Page 4: Check Compatibility Of Vehicle And Accessories

    1.2. Check compatibility of vehicle and accessories Requirements Vehicle Audi, Lamborghini Navigation Audi Navi Plus RNS-E all-in-one navigation 16:9 Limitations Factory-TV-tuner Must NOT be installed. After-market rear-view Only compatible with NTSC-cameras. camera Automatic switching to camera from OEM mode only works after coding the head-unit to rear-view camera per diagnosis computer (Only possible on RNS-E with minimum software 550 and till year 2010).
  • Page 5: Deactivating C.logic Av2-Input

    1.4.2. Deactivating c.LOGiC AV2-input If only one AV-source shall be connected to the c.LOGiC, we recommend to disable the AV2-input, to avoid customers switching by mistake to black/no picture of the AV2-input. In order to disable the AV2-input of the c.LOGiC, set dip1 = OFF (down).
  • Page 6: Installation

    3. Installation Switch off ignition and disconnect the vehicle’s battery! If according to factory rules disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead.
  • Page 7: Connections To Head-Unit

    3.2. Connections to head-unit Remove the head-unit from the dash-board. Transfer female Quadlock connector from the back of the head-unit to male Quadlock connector of harness C3C-RNSE. Plug female Quadlock connector of C3C-RNSE into male Quadlock socket of head-unit. Plug female 32pin AMP-connector of C3C-RNSE into male 32pin AMP-socket of head- unit.
  • Page 8: Av-Source(S)

    3.3.1. AV-source(s) The c.LOGiC interface has the possibility to connect and remotely control by navigation buttons up to 2 pre-programmed devices. The device list in the device control table (Appendix A) shows the pre-programmed remote channels and the related IR-remote cables STA-xxx which must be ordered separately for the control of the device.
  • Page 9: Installing Av-Source's Ir-Sensor Additionally

    3.3.2. Installing AV-source’s IR-sensor additionally Additionally to the control via OEM navigation, it is possible to install the original IR-sensor of a connected device. By using the respective Y-adapter (e.g. STA-Y35MM or STA-RJ12) for the IR-Port of the connected device, the controls of navigation AND device’s IR-sensor can be connected and used simultaneously.
  • Page 10: After-Market Rear-Seat-Entertainment

    3.3.4. After-market rear-seat-entertainment Using RCA-cables, connect the rear-seat-entertainment to the female RCA-connector VIDEO OUT of Interface-box C2C-M200. Note: As the output is a full output, not shared with the video signal for the navigation system, splitting the video with an RCA Y-cable might give a good enough picture for two rear-seat-entertainment monitors.
  • Page 11: Switching Between Av1 And Av2

    4.3. Switching between AV1 and AV2 After selecting the c.LOGiC as current AV source, longpress the knob to switch between AV1 and AV2. Note: If AV2 is deactivated (see chapter chapter Deactivating c.LOGiC AV2 input), it is not possible to switch to the c.LOGiC’s AV2.
  • Page 12: Picture Settings

    Button assignment table c.LOGiC Audi Navi Plus RNS-E Head- DVB-T USB-LiNK DVD-player DVD- iPod®-control Analog-tuner unit changer button CH - TRACK - TRACK - TRACK - TRACK - CH - 1 long POWER SHUFFLE CH + TRACK + TRACK + TRACK + TRACK + CH +...
  • Page 13: Specifications

    Temperature range -30°C to +80°C Weight 202g Measurements (box only) B x H x T 90 x 30 x 105 mm 6. Technical Support Caraudio-Systems Vertriebs GmbH NavLinkz GmbH manufacturer/distribution corporate sales/tech dealer-support Rheinhorststr. 22 Eurotec-Ring 45 D-67071 Ludwigshafen am Rhein...

Table of Contents