Table of Contents
Advertisement
Quick Links
XX120
MODEL VC5050-DSP DIGITAL
DAY/NIGHT COLOR CAMERA
©
Copyright
2002 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: +44 (0) 1489-566300 INFOFAX: 800-287-1207 WEB www.vicon-cctv.com
Vicon part number 8009-8120-00-00 Section 1 Rev 702
Advertisement
Table of Contents
Related Manuals for Vicon VC5050-DSP
Summary of Contents for Vicon VC5050-DSP
- Page 1 2002 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: +44 (0) 1489-566300 INFOFAX: 800-287-1207 WEB www.vicon-cctv.com...
-
Page 2: Table Of Contents
Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • The optical filter is switched automatically to color image or black CONTENTS and white image according to the subject brightness. -
Page 3: Information To User
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Vicon may This installation should be made by a qualified service person and void the user’s authority to operate this camera. -
Page 4: Shipping Instructions
SHIPPING INSTRUCTIONS Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 5: Precautions
Do not open the cabinet, as it may be dangerous and cause damage as spotlights, etc., or where it could be subject to direct sunlight, as to the unit. For internal settings and repairs, contact Vicon Technical that could cause deformation, discoloration or other damages. -
Page 6: Parts Names
PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. Manual color/black and white setting terminal (CONTROL) •... - Page 7 PARTS NAMES Flange-back lock screw Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment lever (See page 8) Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings.
-
Page 8: Concerning Auto-Iris Lenses
CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO VIDEO type auto-iris lens A. -
Page 9: Flange-Back Adjustment
FLANGE-BACK ADJUSTMENT If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. -
Page 10: Mounting The Lens
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 5 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera. - Page 11 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
-
Page 12: Connections
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Connect to 24 V AC UL listed class 2 power supply. CAUTION: •... -
Page 13: Settings
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. - Page 14 SETTINGS Iris function setting Aperture This should normally be set to the down (AI) position. If you would like to emphasize the contours of the object, set the switch 2 (AP) to the up (SHRP) position. Use a manual or fixed iris lens and set the lens aperture to the shortest F stop.
- Page 15 SETTINGS (MULTI mode: 64 sections) Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 3 (MULT) and 4 (CENT) are set to the down (OFF) position. Change the backlight compensation switch settings depending on the conditions. •...
-
Page 16: White Balance Adjustment
SETTINGS White balance adjustment Line phase adjustment Normally the switch 5 (WB) is set to the down (ATW: auto white When using a camera switcher to connect 2 cameras or more to one balance) position and the white balance is adjusted automatically. If a monitor, there may be a vertical roll of the images when switched. - Page 17 SETTINGS C • • • • B/W (color/black and white) switch setting Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL This switch lets you select the timing of the automatic switching of (VR301) volume when shooting in the conditions described below.
-
Page 18: Troubleshooting
If it still does not perform Connect each pin of the CONTROL terminal as indicated below, to correctly, contact Vicon. See Shipping Instructions on page 3. set the image to black and white or color as desired. -
Page 19: Specifications
SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TV Environmental conditions : Temperature: –10° C ~ +50° C lines, 30 frames/sec.) Humidity: less than 90% (no condensation) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device Power supply : 24 V AC, 60 Hz Power consumption... - Page 20 This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Contact Vicon if you need service. See Shipping Instructions on page 3. English...
- Page 21 Software supplied either separately or in hardware is furnished on an "As Is" basis. Vicon does not warrant that such software shall be error free and if errors do occur, Vicon’s only obligation shall be to exercise due diligence in working to correct such errors.
- Page 22 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Infofax: 800-287-1207 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom 44/(0) 1489/566300 Fax: 44/(0) 1489/566322 Brussels Office Planet II - Unit E...
Need help?
Do you have a question about the VC5050-DSP and is the answer not in the manual?
Questions and answers