Related Manuals for Tennant BR2020
Summary of Contents for Tennant BR2020
- Page 1 BR2020/T Dust Control Burnisher Operator Manual Model No.: BR2020 604778 BR2020T 604777 604742 Rev. 00 (04 98) Home Find... Go To..
-
Page 2: Machine Data
ENGLISH This manual is furnished with each new BR2020/T Model. It provides necessary machine operation MACHINE DATA and maintenance instructions. Read this manual completely and understand the machine before operating or servicing. Please fill out at time of installation for future reference. -
Page 3: Safety Precautions
– Do not run machine where flammable liquids or gases are present. – Do not run on ramps or inclines unless adequate personnel are present for assistance. – Always use extreme caution when maneuvering. BR2020/T (04–98) Home Find... Go To.. -
Page 4: Machine Components
CONTROL PANEL SYMBOLS Fast Speed Pad Pressure Main Power Meter Main Power Read Manual Circuit Breaker Before Operating Slow Speed Less Pad Pressure Parking Brake Pad Motor Circuit Breaker Battery More Pad Charge Meter Reverse Pressure BR2020/T (04–98) Home Find... Go To.. -
Page 5: Machine Installation
CHARGER PLUG parking brake. CONNECT LAST – MACHINE FRONT Connect Battery Cables 6. Double check cable connections and close Set Parking Brake hood, fasten hood latches. 2. Turn OFF all switches and remove key. BR2020/T (04–98) Home Find... Go To.. -
Page 6: Machine Setup
IMPORTANT: Consult your authorized distributor for pad recommendations. Pad Specifications: For 2000 RPM Burnishing. 1”/25,4 mm Thickness Adjusting Control Grip Height 20”/508mm Diameter with 3.5”/89mm center hole. Machine is not designed for spray buffing. NOTE: BR2020/T (04–98) Home Find... Go To.. -
Page 7: Machine Operation
3. Turn speed control knob to slowest speed. 5. Make sure floor is dry. This will prevent an abrupt take off. BURNISHING WITH THE BR2020 1. Turn on key and main power switch. 2. Twist control grips forward to lower pad to floor and to start pad motor. -
Page 8: While Operating Machine
To reset power kill button, shut off all switches and turn kill button to the right. Resume to normal operation. Turn Off Pad Switch CAUTION: When transporting machine without burnishing, tilt machine back to protect dust skirt. Power Kill Button BR2020/T (04–98) Home Find... Go To.. -
Page 9: Circuit Breakers
WARNING: Charge batteries in a well charger must be grounded while in use to ventilated area. Batteries emit hydrogen gas. protect user from electric shock and serious Explosion or fire can result. Keep sparks and injury. open flame away. BR2020/T (04–98) Home Find... Go To.. -
Page 10: Weekly Maintenance
MONTHLY MAINTENANCE 1. Lubricate caster with a water resistant grease. 2. Lubricate wheel grease fittings with a water resistant grease (BR2020 Model). 3. Check machine for loose nuts and bolts. Charging Batteries 4. Check condition of dust skirt, replace if worn. -
Page 11: Transporting Machine
Cloth Bag – 98% @ 1.0 micron BATTERIES 3–12 Volt (optional) 3–12 Volt (optional) RUN TIME, CONTINUOUS Up to 2.4 hours Up to 2.2 hours DECIBEL RATING AT 70dB(A) 70dB(A) OPERATOR’S EAR, INDOORS ON TILE BR2020/T (04–98) Home Find... Go To.. -
Page 12: Troubleshooting
Contact Service Center. board. Loose wire connection. Contact Service Center. Short run time. Low battery charge. Charge batteries. Defective battery cell(s). Replace battery. Batteries need maintenance. See Battery Maintenance. Faulty battery charger. Replace charger. BR2020/T (04–98) Home Find... Go To..
Need help?
Do you have a question about the BR2020 and is the answer not in the manual?
Questions and answers