Heat-N-Glo SL-950TR Installer's Manual
Hide thumbs Also See for SL-950TR:
Table of Contents

Advertisement

Models:
SL-950TR
SL-750TR
SL-750TRS
SL-750TRFL
SL-550TR
SL-550TRS
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
GUIDE
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
1
Installers Guide
Underwriters
Laboratories Listed
INSTALLERS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SL-950TR and is the answer not in the manual?

Questions and answers

Summary of Contents for Heat-N-Glo SL-950TR

  • Page 1 Models: Installers Guide SL-950TR SL-750TR SL-750TRS SL-750TRFL SL-550TR SL-550TRS Underwriters Laboratories Listed INSTALLERS WARNING: IF THE INFORMATION GUIDE IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUS- WARNING: IMPROPER INSTALLA- ING PROPERTY DAMAGE, PER- TION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN SONAL INJURY, OR DEATH.
  • Page 2: Safety And Warning Information

    SAFETY AND WARNING INFORMATION These units MUST use one of the vent systems READ and UNDERSTAND all instructions carefully described in the Installing the Fireplace section of before starting the installation. FAILURE TO the Installers Guide. NO OTHER vent systems or FOLLOW these installation instructions may result components MAY BE USED.
  • Page 3 TABLE OF CONTENTS...
  • Page 4: Service Parts

    Service Parts SL-550TR and SL-550TR-DSI (NG, LP) Exploded Parts Diagram / Vue éclatée des pièces...
  • Page 5 SL-550TR and SL-550TR-DSI (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / STANDING PILOT AND DSI IGNITION COMMON PARTS SERIAL # / N° DE PART NUMBER PIÈCE UNE VEILLEUSE ET ALLUMAGE DSI PIÉCES COMMUNES SÉRIE / N° DE PIÈCE ON/OFF Rocker Switch / Interrupteur à...
  • Page 6 Service Parts SL-550TRS-B (NG, LP) Exploded Parts Diagram / Vue éclatée des pièces...
  • Page 7 SL-550TRS-B (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / SERIAL # / N° DE PART NUMBER STANDING PILOT IGNITION / D’ALLUMAGE PAR VEILLEUSE PIÈCE SÉRIE / N° DE PIÈCE Piezo Ignitor / Allumage Piézo 418-513 Burner Tube / Tube de brûleur 477-301A Burner Orifice NG (#38A) / Orifice de brûleur GN (#38A)
  • Page 8 Service Parts SL-750TR and SL-750TR-DSI (NG, LP) Exploded Parts Diagram / (GN, PL) Vue éclatée des pièces...
  • Page 9 SL-750TR and SL-750TR-DSI (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / STANDING PILOT AND DSI IGNITION/ SERIAL # / N° DE PART NUMBER UNE VEILLEUSE ET ALLUMAGE DSI PIÈCE SÉRIE / N° DE PIÈCE ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt 060-511 Burner Tube / Tube de brûleur 477-301A...
  • Page 10 Service Parts SL-750TRS-B (NG, LP) Exploded Parts Diagram / (GN, PL) Vue éclatée des pièces...
  • Page 11 SL-750TRS-B (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / SERIAL # / N° DE PART NUMBER STANDING PILOT IGNITION / ALLUMAGE UNE VEILLEUSE PIÈCE SÉRIE / N° DE PIÈCE Piezo Ignitor / Allumage Piézo 418-513 Burner Tube / Tube de brûleur 477-301A Burner Orifice NG (#36A) / Orifice de brûleur GN (#36A)
  • Page 12 Service Parts SL-750TRFL (NG, LP) Exploded Parts Diagram / (GN, PL) Vue éclatée des pièces...
  • Page 13 SL-750TRFL (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / SERIAL # / PART NUMBER STANDING PILOT IGNITION / ALLUMAGE UNE VEILLEUSE P IÈ C E N° DE SÉRIE / N° DE PIÈCE ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt 060-511 Piezo Ignitor / Allumage Piézo 418-513...
  • Page 14 Service Parts SL-950TR and SL-950TR-DSI (NG, LP) Exploded Parts Diagram / (GN, PL) Vue éclatée des pièces...
  • Page 15 SL-950TR and SL-950TR-DSI (NG, LP) Service Parts List / Liste des pièces de rechange ITEM / SERIAL # / N° DE PART NUMBER STANDING PILOT AND DSI IGNITION/ UNE VEILLEUSE ET ALLUMAGE DSI PIÈCE SÉRIE / N° DE PIÈCE ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt 060-511 Burner Tube / Tube de brûleur...
  • Page 16: Approvals And Codes

    Approvals and Codes Appliance Certification High Altitude Installations Installers Guide Certification Installation Codes...
  • Page 17: 2 Getting Started

    Getting Started Introducing the Heat-N-Glo Gas Fireplaces Installers Guide Pre-install Preparation Installers Guide...
  • Page 18 37 3/4 (959mm) 1/2 (13mm) 18 7/8 (479mm) 16 1/4 (413mm) 15 3/4 (400mm) 6 5/8 (168mm) 8 3/4 (222mm) (Top Vent Collars) (REAR VENT COLLARS CENTER LINE) 8 5/8 (219mm) 38 1/2 (978mm) 24 1/2 (622mm) 41 3/4 (1061mm) 28 1/2 (724mm) LINE ELECTRICAL...
  • Page 19 30 3/4 (781mm) 1/2 (13mm) 15 3/8 (390mm) 16 1/4 (413mm) 15 3/4 (400mm) 8 3/4 (222mm) 6 5/8 (168mm) (TOP VENT COLLARS) (REAR VENT COLLARS CENTER LINE) 8 5/8 (219mm) 34 1/2 (876mm) ELECTRICAL 37 3/4 (960mm) 22 1/2 (572mm) ACCESS 24 1/2 (623mm) LINE...
  • Page 20 25 3/4 (654mm) 1/2 (13mm) 12 7/8 (327mm) 16 1/4 (413mm) 15 3/4 (400mm) 8 3/4 (222mm) 6 5/8 (168mm) (TOP VENT COLLARS) (REAR VENT COLLARS CENTER LINE) 8 5/8 (219mm) 31 (787mm) 19 (483mm) 32 1/2 (826mm) 21 (534mm) LINE ACCESS ELECTRICAL...
  • Page 21: Installing The Fireplace

    CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING. VENT FRAMING HOLE 1/2 “ MIN. (13mm) Framing should be SL-950TR 49” 16 1/4” 35 3/8” 50” 70 3/4” constructed of 2 X 4 SL-750TR & TRS 42”...
  • Page 22 8 5/8” (220mm) DV-45D 35 3/4” 47 3/4” (908mm) (1.2m) 11 3/4” (298mm) 8 3/4” 5 3/4” (222mm) (146mm) DV-09D DV-12D DV-06D NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOINT.
  • Page 23 6 1/2 6 3/8 9 1/4 6 1/2 9 5/8 6 3/8 6 5/8 SL-45D 6 5/8 9 5/8 SL-90D 17-24 6 1/2 11 3/4 5 3/4 6 5/8 SL-17/24D (SL17-24D) SL-12D SL-06D 47 3/4 35 3/4 23 3/4 12-17 8 3/4 SL-09D SL-12/17D (SL12-17D)
  • Page 24 Step 3. Installing the Vent System Identifying Vent Components Installers Guide Vent System Termination Kits D-SERIES VERTICAL TERMINATION STORM COLLAR DVK-01D ROOF FLASHING DVK-TVCD HORIZONTAL HORIZONTAL PIPE TERMINATION SUPPORT DVK-01TRD PIPE LENGTH SL D-SERIES WALL FIRESTOP WALL BRACKET SLK-01D 90 DEGREE CEILING ELBOW FIRESTOP...
  • Page 25 V (FT.) 40' MAX. For corner installation STRAIGHT OUT HORIZONTAL VENTING of models SL-550TR and SL-750TR ONLY. Max. Run 24" (610 mm) 45-DEGREE ELBOW 90-DEGREE ELBOWS...
  • Page 26 VENTING WITH ONE (1) 90 ELBOW NATURAL GAS MODEL SL-550TR MODEL SL-750TR MODEL SL-950TR H (MAX.) H (MAX.) V (MIN.) H (MAX.) Elbow on Top 2.5 FT (863mm) 2.5 FT (863mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm)
  • Page 27 VENTING WITH ONE (1) 90 ELBOW NATURAL GAS MODEL SL-550TRS MODEL SL-750TRS V (MIN.) H (MAX.) H (MAX.) Elbow on Top 2 FT (610mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm) 3 FT (914mm) 2 FT (610mm) 4 FT (1.22m) 4 FT (1.22m) 3 FT (914mm) 6 FT (1.86m)
  • Page 28 H + H 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX. (1.86 m) 12' MAX. (3.6m) 4' MIN. (1.22 m) 8' MAX.
  • Page 29 VENTING WITH TWO (2) 90 ELBOWS NATURAL GAS MODEL SL-550TR MODEL SL-750TR MODEL SL-950TR V (MIN.) H + H (MAX.) H + H (MAX.) H + H (MAX.) Elbow on Top 2.5 FT (863mm) 2.5 FT (863mm) 2 FT (610mm)
  • Page 30 VENTING WITH TWO (2) 90 ELBOWS NATURAL GAS MODEL SL-550TRS MODEL SL-750TRS V (MIN.) H + H (MAX.) H + H (MAX.) Elbow on Top 2 FT (610mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm) 3 FT (914mm) 2 FT (610mm) 4 FT (1.22m) 4 FT (1.22m)
  • Page 31 VENTING WITH TWO (2) 90 ELBOWS NATURAL GAS MODEL SL-750TR MODEL SL-950TR MODEL SL-550TR V (MIN.) H (MAX.) H (MAX.) H (MAX.) Elbow on Top 2.5 FT (863mm) 2.5 FT (863mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm)
  • Page 32 VENTING WITH TWO (2) 90 ELBOWS NATURAL GAS MODEL SL-550TRS MODEL SL-750TRS V (MIN.) H (MAX.) H (MAX.) Elbow on Top 2 FT (610mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm) 3 FT (914mm) 2 FT (610mm) 4 FT (1.22m) 4 FT (1.22m) 3 FT (914mm) 6 FT (1.86m)
  • Page 33 H + H 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.48m) 3' MIN. (914 mm) 6' MAX. (1.86m) 12' MAX. (3.72m) 4' MIN. (1.22 m) 8' MAX. (2.48m) 16' MAX.
  • Page 34: Natural Gas

    VENTING WITH THREE (3) 90 ELBOWS NATURAL GAS MODEL SL-550TR MODEL SL-750TR MODEL SL-950TR V (MIN.) H (MAX.) H + H (MAX.) H (MAX.) H + H (MAX.) H (MAX.) H + H (MAX.) Elbow on Top 2.5 FT (863mm) 4 FT (1.22m)
  • Page 35 VENTING WITH THREE (3) 90 ELBOWS NATURAL GAS MODEL SL-550TRS MODEL SL-750TRS V (MIN.) H (MAX.) H + H (MAX.) H (MAX.) H + H (MAX.) Elbow on Top 2 FT (610mm) 4 FT (1.22m) 2 FT (610mm) 4 FT (1.22m) 1 FT (305mm) 3 FT (914mm) 6 FT (1.86m)
  • Page 36 VENTING WITH THREE (3) 90 ELBOWS NATURAL GAS MODEL SL-550TR MODEL SL-750TR MODEL SL-950TR V (MIN.) H + H (MAX.) H + H (MAX.) H + H (MAX.) Elbow on Top 2.5 FT (863mm) 2.5 FT (863mm) 2 FT (610mm)
  • Page 37 VENTING WITH THREE (3) 90 ELBOWS NATURAL GAS MODEL SL-550TRS MODEL SL-750TRS V (MIN.) H + H (MAX.) H + H (MAX.) Elbow on Top 2 FT (610mm) 2 FT (610mm) 1 FT (305mm) 3 FT (914mm) 3 FT (914mm) 2 FT (610mm) 4 FT (1.22m) 4 FT (1.22m)
  • Page 38 VENTING WITH FOUR (4) ELBOWS NATURAL AND PROPANE GAS V (MIN.) H (MAX.) (MIN.) (MAX.) (MIN.) 2' (609mm) 5' (1.52m) 5' (1.52m) 5' (1.52m) 4.5' (1.37m) V + V + H + H MAX. = 40' (12.2m)
  • Page 39 STARTING COLLAR 3/8” (9.5mm) STOVE SEALANT BEAD FIRST VENT COMPONENT 1 INCH (25.4mm) Insert screwdriver or similar object here to remove cap. SEAL INSULATION, SEAL DISCARD BOTH PIECES HEAT SHIELD HEAT DISCARD SHIELD INSULATION CUT HERE...
  • Page 40 12" or 10" (305mm or 254mm) 1" (25.4 mm) 12" or 10" (305mm or 254mm) VENT PIPE WALL BRACKET WALL STUD HEAT SHIELD TRIM HEAT SHIELD IF TOO LONG, ADD TO SHIELD IF TOO SHORT 8 FT. (2.4m) EXTERIOR FIRESTOP INTERIOR FLUE FIRESTOP...
  • Page 41 JOIST CEILING NAILS (4 REQUIRED) CEILING FIRESTOP 11" (280 mm) or 11" (280mm) or 10" (254 mm) 10" (254mm) NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm). CHIMNEY HOLE NAILS (4 REQUIRED) EXISTING CEILING JOISTS FRAMING MEMBERS CEILING...
  • Page 42 C. Vent Termination ROUND CAP TERMINATION PERFORATION CANNOT BE INSIDE THE WALL 7 1/2" (191mm) MINIMUM TRAPEZOID CAP TERMINATION 7 1/4" (184mm)
  • Page 43 1 2 3 4 1 2 3 4 CAUTION: IF INSTALLING UNITS SL-550TRS, SL-750TRS OR SL-950TR, AND EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALL THE VINYL PROTECTOR KIT TO THE TOP OF THE EXTERIOR FIRESTOP (FOR ALL ROUND TERMINATION CAPS).
  • Page 44 HORIZONTAL OVERHANG 2 FT. 2 FT. MIN. VERTICAL MIN. WALL LOWEST DISCHARGE OPENING TERMINATION ROOF PITCH IS X/ 12 H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING NOTE: This also pertains to vertical vent systems in- stalled on the outside of the building.
  • Page 45: Securing The Fireplace

    Step 4. Positioning, Leveling, and Step 5. The Gas Control Systems Securing the Fireplace Standing Pilot Ignition Direct Spark Ignition (DSI). WARNING: To ensure proper clearances the front framing header must be installed on its narrow edge and to the front of the frame.
  • Page 46 Step 7. Gas Pressure Requirements Step 6. The Gas Supply Line USE A WRENCH ON SHUT-OFF VALVE WHEN TIGHTENING GAS LINE MANUAL SHUT-OFF VALVE GAS VALVE FLEX CONNECTOR GAS ACCESS...
  • Page 47 REMOTE SWITCH 3/16” PIGGYBACK CONNECTOR PIGTAIL BLACK S2 ON/OFF WHITE T2 SWITCH GAS VALVE RED T1 THERMOPILE BLACK S1 THERMOCOUPLE OPTIONAL WALL SWITCH, THERMOSTAT OR REMOTE Step 8. Wiring the Fireplace CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENTAL FIREPLACE OPERATION.
  • Page 48 DSI CONTROL VALVE OPTIONAL REMOTE, WALL SWITCH OR THERMOSTAT (0N CERTIFIED UNITS ONLY) (NEUTRAL) JUNCTION OPTIONAL FAN (HOT) SWITCHES 120VAC IGNITOR BLACK ON/OFF WHITE BLUE GROUND DSI MODULE WHITE BLACK GROUND GREEN FIREPLACE CHASSIS BLUE FLAME WHITE SENSOR/SPARKER ON/OFF SWITCH IGNITION MODULE VALVE...
  • Page 49 CAUTION: IF JOINTS BETWEEN THE FINISHED WALLS Step 9. Finishing AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 300° F. MINIMUM SEALANT MATE- RIAL MUST BE USED. THESE JOINTS ARE NOT RE- QUIRED TO BE SEALED. ONLY NON-COMBUSTIBLE MATERIAL (USING 300°...
  • Page 50 Step 10. Installing Trim, Logs and Ember Material, and Removing Shipping Support CAUTION: THE GLASS DOOR MUST BE SECURELY LATCHED BEFORE OPERATING THE UNIT. LATCHES (BOTH BOTTOM AND TOP) GLASS ASSEMBLY Figure 45 EMBER MATERIALS CAUTION: IT IS STRONGLY RECOMMENDED THAT TRIM DOORS WITH OPTIONAL MESH SCREENS BE IN- STALLED ON PROPANE MODELS.
  • Page 51 Step 12. Lighting the Fireplace Step 11. Before Lighting the Fireplace Installers Guide After the Installation...
  • Page 52: Maintaining And Servicing Your Fireplace

    Maintaining and Servicing Your Fireplace Fireplace Maintenance MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATING.

This manual is also suitable for:

Sl-750trflSl-750trSl-550trSl-750trsSl-550trs

Table of Contents

Save PDF