Table of Contents
Advertisement
Models:
SL-950TR-C
SL-750TR-C
SL-550TR-C
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Printed in U.S.A. Copyright 2004,
Heat-N-Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
Please contact your Heat-N-Glo dealer with any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 1-888-427-3973.
1
Installers Guide
Underwriters
Laboratories Listed
530-985N 4/04
Advertisement
Table of Contents
Related Manuals for Heat-N-Glo SL-750TR-C
Summarization of Contents
Safety and Warning Information
General Safety Precautions
Crucial safety instructions regarding fire, explosion, property damage, and personal injury if not followed.
Unit Specific Warnings
Prohibitions against use with water damage, solid fuel, and obstructions to airflow.
Ventilation and Component Safety
Guidelines on proper venting, glass door handling, and maintenance.
Clearance and Proximity Guidelines
Mandatory clearances from combustible materials and furniture for safe operation.
Approvals and Codes
Appliance Certification Standards
Details on models tested, certified by laboratories, and standards met.
Installation Code Requirements
Conformity to local codes, National Fuel Gas Code, and NEC/CSA standards for installation.
High Altitude Installation Adjustments
Guidelines for adjusting input rating and orifice size for installations above 2,000 feet.
Getting Started
Introducing Heat-N-Glo Gas Fireplaces
Overview of direct vent gas fireplaces and their operation.
Pre-installation Preparation Steps
Steps and cautions before installation, including checking parts and reading instructions.
Installing the Fireplace
Fireplace Chase Construction
Guidelines for building a chase, emphasizing insulation, sealing, and code compliance.
Locating the Fireplace Position
Requirements for fireplace placement, including space and clearance specifications.
Fireplace Framing
Framing Dimensions and Methods
Instructions for framing the fireplace, accommodating wall coverings and facing materials.
Installing the Vent System
Vent System Approvals and Components
Details approved vent components (DVP/SL-D) and emphasizes not mixing series.
Venting Specifications
Flex Vent and Horizontal Venting
Guidelines for flex vent installation and specific configurations for horizontal venting.
Venting Lengths with One 90° Elbow
Maximum horizontal (H) and vertical (V) lengths for one 90° elbow with TR-C models.
Venting Lengths with Two 90° Elbows
Maximum horizontal (H) and vertical (V) lengths for two 90° elbows with DVP-Series components.
Venting Lengths with Three 90° Elbows
Maximum vertical (V, V1) and horizontal (H, H1) lengths for three 90° elbows with DVP-Series components.
Venting Lengths with Four 90° Elbows
Maximum lengths for four 90° elbows with TR-C models (Natural and Propane Gas).
Vent Component Installation
Installing Vent Components (DVP & SL-D)
Detailed steps for attaching DVP and SL-D series vent components, including sealing and locking.
Installing Support Brackets
Guidelines for installing support brackets for horizontal and vertical vent runs.
Firestop and Termination Installation
Installing Firestops
Procedure for installing firestops for horizontal and vertical vent runs through walls and ceilings.
Vent Termination Procedures
Instructions for attaching SL-Series and DVP-Series vent termination caps, including positioning and sealing.
Vent Termination Clearances
Minimum Clearances for Vent Terminals
Minimum required clearances for vent terminals based on location and termination type.
Vertical Vent Termination Heights
Minimum Height from Roof to Discharge
Minimum vent pipe height above roof based on roof pitch for proper discharge.
Fireplace Installation and Gas Controls
Positioning, Leveling, and Securing
Detailed instructions for properly positioning, leveling, and securing the fireplace unit.
Gas Control Systems Overview
Explanation of the two gas control systems: Standing Pilot and Intermittent Pilot Ignition (IPI).
Gas Supply and Pressure Requirements
Gas Supply Line Installation
Installation of the gas supply line, including connection to the control valve and leak testing.
Gas Pressure Specifications
Table of minimum and maximum inlet pressure and manifold pressure for Natural Gas and Propane.
Fireplace Wiring
Standing Pilot Ignition Wiring
Electrical wiring requirements for standing pilot ignition, optional accessories, and wall switches.
IPI Wiring and Battery Operation
Intermittent Pilot Ignition Wiring
Wiring instructions for IPI systems, including 110-120 VAC connection and optional battery backup.
Fireplace Finishing and Surround
Finishing Guidelines and Sealant Use
Guidelines for finishing the fireplace surround, including combustible material placement and sealant requirements.
Installing Trim, Logs, and Ember Material
Installing Trim and Removing Shipping Support
Instructions for installing trim, surround materials, and removing grate shipping support.
Placing Ember Material and Positioning Logs
Detailed steps for placing ember material and positioning gas logs for optimal performance.
Pre-Lighting Checks and Operation
Before Lighting the Fireplace
Pre-lighting checks including removing paperwork, reviewing safety, and checking for gas leaks.
Lighting the Fireplace Procedure
Final steps before lighting the fireplace, emphasizing user manual reference for operation.
Maintaining and Servicing Your Fireplace
Fireplace Maintenance Schedule
Overview of required maintenance tasks and recommended frequencies for servicing.
Vent System and Glass Door Cleaning
Procedure for inspecting the vent system and cleaning the glass door.
Burner, Controls, and Flame Sensor Maintenance
Annual cleaning of burner, controls, and periodic cleaning of the flame sensor rod.
Flame Pattern and Height Checks
Periodic visual checks of flame patterns, height, and thermopile/thermocouple coverage.
Need help?
Do you have a question about the SL-750TR-C and is the answer not in the manual?
Questions and answers