Related Manuals for Risco GARDTEC 872
Summary of Contents for Risco GARDTEC 872
- Page 1 LCD User Instructions & LED User Instructions...
-
Page 2: Table Of Contents
User Manual GARDTEC 872 Contents User Information ............Using LCD Keypads Introduction ..............User Code Types ............Duress Codes ............... Setting The System ............Setting & Unsetting via a Keyswitch ......Unsetting The System ..........Part Setting The System .......... -
Page 3: User Information
User Manual GARDTEC 800 Series User Information Customer Name:- Customer Address:- Control Panel Model No of Keypads Keypad 1 Location Type Keypad 2 Location Type Keypad 4 Location Type Keypad 5 Location Type Keypad 6 Location Type Keypad 7 Location Type Keypad 8 Location Type... -
Page 4: Introduction
GARDTEC 800 Series Introduction The Gardtec 872 control panel is a multi zone microprocessor controlled unit. Two types of display are available for the system keypads, a) LCD offering a 32 character display with zone descriptors and user names or, b) Twin seven segment LED displays offering limited control/user programming options. -
Page 5: Duress Codes
GARDTEC 872 Duress Codes Duress Codes may be programmed onto your GardTec 872 system. When used a Duress code will appear to operate the security system in the normal way but will also send a PA (personal attack) signal to central station (if programmed). -
Page 6: Setting The System
User Manual GARDTEC 872 Setting The System With the display showing:- < < < < UN-SET > > > > 01 JAN 18 : 58 : 01 Enter the User code (followed by YES if Master or Main type code has been used). -
Page 7: Unsetting The System
User Manual GARDTEC 872 Unsetting The System Enter the premises via the authorised entry route (the broken entry tone will sound), proceed to the keypad. At the keypad enter a valid code, the display will show:- < < < < UN-SET > > > >... - Page 8 User Manual GARDTEC 872 The exit tone may or may not be heard dependant on the system settings. Exit the premises or retire to an unprotected part of the system. At the end of the exit time either the exit sounder will stop or a single beep will be emitted (dependant on system settings).
-
Page 9: Area Setting
User Manual GARDTEC 872 Area Setting (using Master or global Main codes) Areas will need to have been set up by the installation company. < < < < UN-SET > > > > With the display showing:- 01 JAN 18 : 58 : 01... -
Page 10: Removing Zones
User Manual GARDTEC 872 Removing Individual Zones (Master & Main codes only) If programmed by the installation company individual zones may be removed, this may only be done by a Master or Main level of code. It should be noted that if an Area Main code is being used, only zones associated with that area may be removed. -
Page 11: Testing The System
User Manual GARDTEC 872 Testing The System (Master & Main codes only) < < < < UN-SET > > > > With the display showing:- 01 JAN 18 : 58 : 01 Enter a Master or Main level code, Do you want to . . -
Page 12: Viewing The Event Log
User Manual GARDTEC 872 Whilst in Test mode any zones violated will sound the internal sounder (if it has not been silenced) and show on the display. When you have finished testing the system press 0 twice, the display will show:- <... -
Page 13: Changing The Chime Status
User Manual GARDTEC 872 This is the most recent event in the log. Whilst viewing the Log, Pressing NO will move back to the previous event. Pressing YES will move forward to the next event. Pressing 7 will take you to back to the last event of the previous day. - Page 14 User Manual GARDTEC 872 Press YES the display will show for example:- Chime is Off ok ? Or:- Chime is On ok ? Press NO to change the status of the Chime, then press YES, the display will show:- Do you want to . .
-
Page 15: Programming User Codes
User Manual GARDTEC 872 Programming User Codes (Master code only) The charts on pages 2 & 35 should be completed by the engineer/user for future reference of what codes have been allocated on your system. Under no circumstances should the actual user code be written down. - Page 16 User Manual GARDTEC 872 Enter the code you require (codes may be 4, 5 or 6 digits) followed by YES. (Entering 000000 will delete an existing code) Note: If the code already exists or is a duress of another code an error will be shown,...
- Page 17 User Manual GARDTEC 872 Referring to the character map enter the required character (pressing the 3 key will display 'G', pressing it again will show 'H' and again will show 'I '), once the correct character is displayed press YES and the display will move on to the next position.
-
Page 18: Programming Time & Date
User Manual GARDTEC 872 Programming Time & Date With the display showing:- < < < < UN-SET > > > > 01 JAN 18 : 58 : 01 Enter a Master Code, the display will show:- Do you want to . . -
Page 19: User Initiating Remote Access
User Manual GARDTEC 872 User Initiating Remote Access (Optional) Access Remote allows your installation company to examine your system and re- program system settings as you need the changes without the need for an engineer to visit your premises. If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call (usually on lines with incoming calls barred). -
Page 20: Resetting After An Alarm
User Manual GARDTEC 872 Resetting After an Alarm Your installation company will have programmed the reset modes for your system so that it complies to your insurance company and legislation requirements. Your installation company will have informed you as to the type of reset that your system is set for. - Page 21 User Manual GARDTEC 872 To reset the system with an anti-Code, contact the central station or engineer (as instructed by the installation company) and quote the source given by the display. The central station or engineer will give a return Anti-Code ( this may contain the YES &...
-
Page 22: Using Led Keypads
User Manual GARDTEC 872 Using LED Keypads This section is dedicated to using LED keypads (Twin Seven Segment). Setting The System With the display showing Enter the User Code (followed by YES if Master or Main type code has been used). -
Page 23: Part Setting The System
User Manual GARDTEC 872 Part Setting The System (using Master & Main type codes) With the display showing Enter a Master or Main type code The display will show (flashing). Press 1, 2 or 3 (for Part 1, 2 or 3) the... -
Page 24: Area Setting
User Manual GARDTEC 872 Area Setting (using Master or Global Main codes) With the display showing Enter a Master or global Main code. The display will show (flashing) Press YES to start setting the system, the exit tone will sound. -
Page 25: Testing The System
User Manual GARDTEC 872 The display will show If you wish to remove other zones return to step 5 To escape press 0 the display will show (flashing). Press YES to start setting the system. Exit the premises or retire to an unprotected part of the system. At the end of the exit time the exit tone will stop provided the system was clear. -
Page 26: Viewing The Event Log
User Manual GARDTEC 872 Viewing The Event Log (Master code only) To get the full capability from the Log we recommend using an LCD keypad With the display showing enter a Master code. The display will show (flashing), press NO three times. -
Page 27: Changing The Chime Status
User Manual GARDTEC 872 Changing The Chime Status (Master code only) The Chime zones will have previously been programmed by your installation company. A Master level code may change the status of the chime between On and Off. To do... -
Page 28: User Initiating Remote Access
User Manual GARDTEC 875 Programming Date & Time Date & Time may only be programmed via an LCD keypad User Initiating Remote Access Users should only initiate Remote Access when instructed to do so by the installation company. With the display showing enter a master level code then press NO seven times the display will flash (Wait) then C H (Dialling) then... -
Page 29: Resetting After An Alarm
User Manual GARDTEC 872 Resetting After An Alarm Your installation company will have programmed the reset modes for your system so that it complies to your insurance company and legislation requirements. Your installation company will have informed you as to the type of reset that your system is set for. -
Page 30: Led Display Glossary
User Manual GARDTEC 872 LED Display Glossary Displays During Normal Use Tamper keypad 4 (may show 1 to 4). System Unset. Reset is required by a higher The system is full setting. level code or an error has occurred whilst programming. - Page 31 User Manual GARDTEC 872 Displays Whilst Viewing Log E A zone on test has failed. Please be aware not all Log Events read Log. can be viewed on an LED keypad. We recommend the use of an LCD keypad.
-
Page 32: System Attributes
User Manual GARDTEC 872 System Attributes Zone No. Zone Type Descriptor Areas Part Info Example Front Door 1&2 A1 Pt2 Page... - Page 33 User Manual GARDTEC 872 Page...
- Page 34 User Manual GARDTEC 872 Page...
-
Page 35: Service Record
User Manual GARDTEC 872 Service Record Date Comments Signature Alarm Reset Type:- Tamper Reset Type:- Page... -
Page 36: User Chart
User Manual GARDTEC 872 User Chart Please use this chart to indicate what user names have been programmed onto your system and those that are in use. In Use Name User 25 User 1 User 26 User 2 User 27... - Page 37 User Manual GARDTEC 872 In Use Name User 76 User 49 User 77 User 50 User 78 User 51 User 79 User 52 User 80 User 53 User 81 User 54 User 82 User 55 User 83 User 56 User 84...
-
Page 38: Ace Instructions
GARDTEC 872 ACE User Instructions ACE (Advanced Control Equipment) allows control of your Gardtec 872 system via Infra-Red Remote control. Ace is available built in to a range of keypads or as a stand alone unit, control is via neat remote keyfob(s). -
Page 39: Programming Ace Keyfobs Onto Your System
User Manual GARDTEC 872 Programming ACE Keyfobs onto your System Two modes are available for ACE, these are ‘Normal’ & ‘High’ Security. Please check the User Information Chart on page 2 noting the mode of your ACE control. Normal Security... - Page 40 GardTec Ltd Internet: http://www.gardtec.ltd.uk e-mail: sales@gardtec.ltd.uk PR5407 Rev1.0...
Need help?
Do you have a question about the GARDTEC 872 and is the answer not in the manual?
Questions and answers