Cw Mode Operation; Etup For Traight Ey And Traight Ey Emulation Peration - Yaesu FT DX 3000 Operating Manual

cw m
oDe
The powerful CW operating capabilities of the FT
ey or a computer ased eying de ice.
S S
etup For trAight
efore starting connect your ey line s to the front and or rear panel KEY jac s . e sure the [ BK-IN button is
turned off for now.
ress the [ MODE button to engage CW operation.
.
he CW and USB icons ill appear in the dis-
inside the [ MONI button glows or-
play. he
ange and the monitor is acti ated.
A :
dvice
If you select the
the e erse mode
side and injection is used compared to the normal
side and. he CW and LSB icons
in the display if you select
. otate the ain uning
sired operating fre uency.
ress the [ BK-IN button to engage automatic acti-
.
vation of the transmitter when you close the CW key.
inside the [ BK-IN button glows orange.
he
A :
dvice
hen you close your
ill automatically e acti ated and the
rier will be transmitted. When you release the
ey transmission
delay recei e ill e restored. he delay time is
user-programmable per the discussion on page
83.
s shipped from the factory the FT
system for
rea in operation.
061 CW BK-IN
for full rea in
s itching is uic enough to hear incoming sig-
nals in the spaces between the dots and dashes of
your transmission. This may prove very useful
during contest and traffic handling operations.
. peration using your
A :
dvice
You may adjust the CW sidetone audio level setting
of enu item 035 MONITOR LEVEL .
o adjust the onitor le el
cti ate the I circuitry if necessary.
t :
erMinology
Semi-break-in
his is a pseudo
release of the ey ill allo the recei er to reco er after a short delay. o signals ill e heard during the spaces
et een dots and dashes unless the sending speed is e tremely slo
Full break-in
ull rea in also no n as
signals may be heard between the dots and dashes as you send them. This allows you to hear a station that sud-
denly starts transmitting on your fre uency
Page 76
o
peration
3000 permit operation using an electronic eyer paddle a straight
DX
(
K
ey And
mode again you ill engage
here y the opposite
ill appear
e erse.
ial no to select the de-
ey the transmitter
car-
ill cease and after a rief
3000
DX
is configured for emi
o e er using enu item
you may change this setup
operation here y the
ey may no proceed.
mode used on here y the closure of the
ull in ol es ery fast s itching et een transmit and recei e incoming
hile you are in the midst of a transmission.
S K
trAight ey eMulAtion
[ BK-IN ] Button
ress and hold in the [ MONI button for one
second to enter the
LEVEL .
ress the [ SELECT
hile eying rotate the [ CLAR/VFO-B knob
or press the
level.
hen you are satisfied
the [ SELECT
button to save the new setting and exit to normal
operation.
If you set the [ BK-IN
tice sending
ing the signal go out over the air.
If you reduce po er ia the
MAX POWER the
this is normal and does not indicate any problem
hatsoe er ecause increased
used to lower the power).
ey ill engage the transmitter and
.
FT
DX
) o
perAtion
[ MONI ] Button [ MODE ] Button
enu item 135 MONITOR
utton .
button) to adjust the monitor
ith the setting press
utton then press the [ MENU
utton to ff you may prac-
ith the sidetone only ithout ha -
enu item 177 TX
meter reading ill increase
oltage is eing
3000 O M
peraTing anual