Yaesu FT DX 3000 Operating Manual page 29

[ VOX ] (see page 72)
his is the or
oice actuated transmitter s itching in the
and modes. he controls affecting
operation are the enu items 181 VOX GAIN
and 183 ANTI VOX GAIN .
182 VOX DELAY
y proper adjustment of these controls hands free
voice-actuated operation is possible.
[ METER ]
This indicator determines the function of the meter
during transmission.
ress the [
TER indicator then press the [ SELECT button
to select meter function in the transmit mode as fol-
lo s
à à à
PO ALC SWR
Indicates the
PO
atts on transmit.
Indicates the relati e
ALC
Indicates the tanding
SWR
e ected .
COMP Indicates the speech compressor le el
mode only).
Indicates the final amplifier drain current.
ID
Indicates the final amplifier drain oltage.
VDD
[ PROC ] ( Processor) (see page 68)
his indicator ena les the peech rocessor for
transmission. djustment of the rocessor le el is
accomplished via the [ PROC/CAR knob.
A :
dvice
he peech rocessor is a tool for increasing
the average power output through a compres-
sion techni ue. o e er if the rocessor le el
is ad anced too far the increase in compression
ecomes counter producti e as intelligi ility
will suffer. We recommend that you monitor the
sound of your signal using the
headphones).
[ DNR ] (see page 57)
This indicator turns the
cei er s igital oise eduction circuit on and off.
djustment of the oise eduction le el is accom-
plished ia the enu item 110 DNR LEVEL .
F T 30 00 O
DX peraTing
indicator for the automatic
uttons to select the ME-
à
COMP
PO ......
à à à
ID VDD
o er utput from
oltage.
a e atio or ard
onitor ith
ain and re-
M
anual
D
isplaY
[ MIC EQ ] (see page 66)
his indicator ena les the hree
icrophone
acti ated ia the
[ DNF ] (see page 57)
This indicator turns the
er s igital otch ilter on and off. his is an auto-
matic circuit and there is no adjustment no for the
.
[ KEYER ] (see page 77)
This indicator toggles the internal CW keyer on and
off. he eyer sending speed is adjusted ia the
front panel's [ MIC/SPEED knob and the CW Hang
ime is adjusted ia the
DELAY .
[ ZIN/SPOT ] (see page 81)
This indicator enables the CW receiver spotting tone.
to
y matching the
signal precisely the same pitch you
ero eating your transmitted signal
uency of the other station.
CLOCK
Indicates the current time.
o set the cloc
. ress and hold the [ C.S
clock digits appear on the display.
. nter the present time ia the num er eys
keys).
. ress the [ ENT button.
4. Setup of the clock is now complete.
Sub ( VFO-B ) Frequency Display
his is the u
A :
dvice
When turning the [ CLAR
[ PROC/CAR
[ SHIFT or [ WIDTH [ MIC
uency or alue will appear in this area for 3 sec-
onds.
DSP Display
This indicator is used for viewing the status of the
i
nDications
and arametric
uali er. he uali er settings are
enu.
ain and
enu item 062 CW BK-IN
tone to that of the incoming
ith the fre-
utton until the ashing
and fre uency display.
[ MIC/SPEED
[ NOTCH [ CONT/APF
no
I and
Page 27
recei -
ill e
and
each fre-
I .