Subscribe to Our Youtube Channel
Related Manuals for ESAB Origo Arc 4001i
Summary of Contents for ESAB Origo Arc 4001i
- Page 1 Origo Arc 4001i Instruction manual 0460 741 001 GB 20121105 Valid for serial no. 833-xxx-xxxx, 852-xxx-xxxx...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 5 There may be potential difficulties in ensuring electromagnetic compatibility of class A equipment in those locations, due to conducted as well as radiated disturbances. - 5 - © ESAB AB 2008 bh35d1ea...
-
Page 6: Introduction
As the person responsible for the equipment, it is your responsibility to obtain information on approved collection stations. For further information contact the nearest ESAB dealer. ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION Arc 4001i is a welding power source intended for welding with coated electrodes (MMA welding) and TIG welding (Live TIG-start). -
Page 7: Technical Data
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at a certain load without overloading. The duty cycle is valid for 40°C. - 7 - © ESAB AB 2008 bh35d1ea... -
Page 8: Installation
(see technical data). In this case it is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment may be connected. - 8 - © ESAB AB 2008 bh35d1ea... -
Page 9: Recommended Fuse Sizes And Minimum Cable Area
Fuse anti-surge 20 A type C MCB 20 A NOTE! Cable size and fuse rating complies to Swedish electrical regulations. Use the welding power source in accordance with the relevant national regulations. - 9 - © ESAB AB 2008 bh35d1ea... -
Page 10: Operation
Whether the mains power supply is interrupted or the power unit is switched off in the normal manner, welding data will be stored so that it is available next time the unit is started. - 10 - © ESAB AB 2008 bh35d1ea... -
Page 11: Connection Of Welding And Return Cable
TIG welding melts the metal of the workpiece, using an arc struck from a tungsten electrode, which does not itself melt. The weld pool and the electrode are protected by shielding gas. - 11 - © ESAB AB 2008 bh35d1ea... -
Page 12: Mig/Mag And Fcaw-S Welding
CAUTION All guarantee undertakings from the supplier cease to apply if the customer attempts any work to rectify any faults in the product during the guarantee period. - 12 - © ESAB AB 2008 bh35d1ea... -
Page 13: Power Source
Ensure that the filter with the finest mesh is placed towards the grille. Reinstall the filter. Welding torch Wear parts should be cleaned and replaced at regular intervals in order to achieve trouble-free welding. - 13 - © ESAB AB 2008 bh35d1ea... -
Page 14: Fault-Tracing
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - 14 - ©... - Page 15 - 15 -...
-
Page 16: Diagram
Diagram - 16 - © ESAB AB 2008 bh35e... - Page 17 - 17 - © ESAB AB 2008 bh35e...
-
Page 18: Ordering Number
Origot Arc 4001i, A24 0459 839 029 Spare parts list Arc 4001i 0460 737 Instruction manual Control panel Origot A22, A24 Instruction manuals and the spare parts list are available on the Internet at www.esab.com - 18 - © ESAB AB 2008 bh35o... -
Page 19: Spare Parts List
Arc 4001i Spare parts list Item Ordering no. Denomination 0458 398 002 Dust filter - 19 - bh35s © ESAB AB 2008... -
Page 20: Accessories
For setting of wire feed speed, current and arc force. Remote control unit AT1 CAN ... . 0459 491 883 For setting of current. - 20 - bh35a11a © ESAB AB 2008... - Page 21 25 m ........0459 960 882 Return cable 5 m 70 mm ....0700 006 895 - 21 - bh35a11a © ESAB AB 2008...
- Page 22 - 22 -...
- Page 23 - 23 -...
- Page 24 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the Origo Arc 4001i and is the answer not in the manual?
Questions and answers