Page 1
Using Your acaia Lunar Coffee Scale Identification The instructions in this operation manual apply to the acaia Lunar Coffee Scale. You have purchased a quality precision weighing scale that requires handling with care. Make sure to read through this operation manual prior to using the scale. ...
Page 2
CAUTION: Any modification made without the consent of the manufacturer will result in the warranty being voided. ...
Chapter 1: Scale at a Glance Introduction Thank you for choosing one of our scales. The acaia Lunar Coffee Scale is designed and manufactured to the most rigorous standard to give you the best coffee brewing experience. Start by checking that your acaia Lunar Coffee Scale box contains all the parts listed below: "...
Accessories Micro USB acaia Scale Weight Charging Cable 100G Micro-B Type A Buttons Function Example Power Turn on Press and hold for 0.5 seconds to turn on the scale. Button Turn off 1. Press and hold for over 3 seconds to turn off the scale.
It takes 1-2 hours to fully charge the battery. You can charge the battery more frequently so that it will never hit empty. Battery percentage can be viewed via acaia APP. It is not recommended to let the battery run out completely before charge.
Chapter 2: Getting Started Preparation This scale is intended for indoor use. Select a work place that is stable, vibration-free and, if possible, a horizontal location for the weighing platform. Do not locate the scale near any equipment/instrument which contains magnets. Avoid places where room temperatures are unstable.
Charging and Setup To use AC adapter instead of the built-in battery, plug the USB cable into the Micro-B USB port located on the back panel of the scale. Press button for 0.5 seconds to turn on the scale. Chapter 1: Scale at a Glance...
Basic Operations Turn On Press and hold button for 0.5 seconds to turn on the scale. Turn Off Press and hold button for 3 seconds to turn off the scale. Or you may double click button to turn off the scale. Switch Modes Press and hold button for 1 second each time to toggle through different modes.
Weighing Mode Display There are two different weighing units in Weighing Mode: grams and ounces. It can be identified if the upper right LED is light on. If the LED is light on, the weighing unit is ounce. The readability is 0.1g or 0.002oz base on the weighing unit selected in Setup mode. For high resolution mode, the readability is 0.01g or 0.0005oz.
Auto Start Mode Display 1. The LED display shows [ 0: 00 0.0] with timer on the left and the weight value on the right. 2. The water mark LED on the right side will light on. 3. The timer displays from [0.00] to [9.59] and then the timer will stop. Operation 1.
1. Press and hold button while turning ON the scale. When the LED display shows [ :ACAIA ]and then[ SEt ] , press and hold button for another 1 second without releasing buttons when the display shows [ F.0000 ]. with the very button.
Tracking is set to be 3d, any initial weight between +/- 0.3g on the weighing pan would be zeroed out gradually. 3. 2d is recommended in general for acaia Lunar Coffee Scale. button for 1 second until the next setting, [ bEEP ], is shown on LED to 4.
2. If Zero Range is set to 100, the range for zero-setting will be 100% of the capacity, i.e., +/- 2kg for acaia Lunar Coffee Scale. Therefore, instead of tare operation, zero operation would be executed in this setting whenever button is pressed.
1. OFF: The bluetooth is disabled. The scale does not allow any bluetooth connection. 2. on: The bluetooth is enabled. The scale allows bluetooth connection. User may connect the scale with acaia APPs. 3. Press and hold button for 1 second until [ SLEEP ] is shown to confirm the modification.
LED display shows [ CAL ] and then [ 500.00 ]. 2. Place acaia 100g weight on scale and wait for the scale to execute calibration procedure. 3. The LED display shows [ _End_ ] when the calibration procedure is completed. You may unload the calibration weight when completed.
Appendix B. Error Codes Error Code List Error Code Description 100 Code error 101 EEPROM error 102 AD read error Over load: the weight is over the maximum capacity. Under load: the weight is under the minimum capacity. 303 Unable to make zero point, for the initial weight exceeds the limit (50% of capacity). 304 Weight calibration error.