Installation - Hoshizaki KM-30A Instruction Manual

ENGLISH
I. INSTALLATION INSTRUCTIONS
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging
elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing
material is left in the icemaker, it will not work properly.
Top Panel
Separator
Door
Accessories
(inside bin)
Control Switch
Air Filter
1) After removing the packaging, make sure that the icemaker is in
good condition. If in doubt, please do not use the equipment but
apply to professionally qualified personnel.
2) Remove shipping tape holding the door and separator.
3) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Outlet Hose
b) Scoop
c) Adjust Bolt
d) Power Supply Cord (European model)
2. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within 7°C to 40°C.
Normal operating water temperature should be within 7°C
to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for
the equipment.
4. Allow 15 cm clearance at rear and sides for proper air
circulation and ease of maintenance and/or service should
they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
Icemaking
Mechanism
Control Box
Refrigeration
Circuit
Louver
Fig. 1
1
1
4
1
6. Do not place anything on top of the icemaker or in front of
the louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").

3. INSTALLATION

* Incorrect installation can cause harm to people, animals or things,
for which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is accessible.
4. ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
1:2
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
1:2
* The main control box fuse is rated at 5A and should only be
replaced by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician
are required.
[Europe]
* If the supply cord is damaged, it must be replaced by a replacement
cord available from Hoshizaki Parts/Service Centres.
[Other than Europe]
* If the supply cord and the plug should need to be replaced, it should
only be done by a qualified service engineer.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol or coloured Green or Green-and-Yellow. The wire which
is coloured Blue must be connected to the terminal which is marked
with the letter N or coloured Black. The wire which is coloured
Brown must be connected to the terminal which is marked with the
letter L or coloured Red.
* Should the socket outlets in the installation site not be suitable for
the plug supplied with your product, the plug must be removed (cut
off if it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord,
it must be disposed of. There should be no attempt to reuse it.
Inserting such a plug into a socket elsewhere presents a serious
risk of electrical shock.
2
WARNING