Advanced System Set Up - HITEC X2 AC Plus Operation Manual

Advanced System Set Up

The system will be set to its default parameters when powered on for the first
time. The screen displays the following information in sequence and the user can
change any given value on each screen.
To change a parameter value in the program, press START/ENTER to make that
value blink. Next, change the value by pressing INC or DEC. The value will be
stored by pressing START/ENTER once.
ITEM SELECTION
ITEM SELECTION
OFF/
OFF/
Safet y T imer ON
Safet y T imer
ON
O N 1 20Mi n
( 1-720 Min )
O N 1 20Mi n
1-720 Min
( )
OFF/
OFF/
Capacit y C ut-Off ON
Capacit y C ut-Off ON
O N 5 000mAH
(
100-50000 mAh)
O N 5 000mAH
( 100-50000 mAh)
OFF/
OFF/
ON
ON
Tem p C ut-Of f
Tem p C ut-Of f (20 C/68 F -
5 0 ° C 1 22 ° F
O N
(20 C/68 F -
5 0 ° C 1 22 ° F
O N
80 C/176 F
)
80 C/176 F
)
Celsius
Temperatur e U nit
Celsius
Temperatur e U nit
Fahrenheit
C elsius
Fahrenheit
C elsius
Res t T ime 1-60Min
Res t T ime 1-60Min
CHG>DCH G 1 0Min
CHG>DCH G 1 0Min
36
DESCRIPTION
DESCRIPTION
When you start a charge process, t he
When you start a charge process, t he
integral safety timer automatically s tarts
integral safety timer automatically s tarts
running at t he s ame time. This i s
running at t he s ame time. This i s
programmed to p revent overcharge the
programmed to p revent overcharge the
battery i f it p roves to be faulty, or i f the
battery i f it p roves to be faulty, or i f the
termination circuit cannot detect the battery
termination circuit cannot detect the battery
full. The value for the safety timer should be
full. The value for the safety timer should be
generous enough to a llow a full charge of
generous enough to a llow a full charge of
the battery.
the battery.
This p rogram sets the maximum charge
This p rogram sets the maximum charge
capacity that will be supplied to the battery
capacity that will be supplied to the battery
during charge. If the delta peak voltage is
during charge. If the delta peak voltage is
not detected nor the safety timer expired by
not detected nor the safety timer expired by
any reason, t his feature will automatically
any reason, t his feature will automatically
stop the process at t he selected capacity
stop the process at t he selected capacity
value.
value.
The battery's internal chemical reaction will
The battery's internal chemical reaction will
cause the temperature of t he battery t o
cause the temperature of t he battery t o
rise. If the temperature limit is reached, the
rise. If the temperature limit is reached, the
process will be terminated.
process will be terminated.
You can choose the temperature displayed
You can choose the temperature displayed
by Celsius or Fahrenheit as you like.
by Celsius or Fahrenheit as you like.
A rest t ime allowing the battery t o cool
A rest t ime allowing the battery t o cool
down between charging/discharging cycle.
down between charging/discharging cycle.
ITEM SELECTION
Advanced System Set Up [
ITEM SELECTION
NiMH Sensitivit y
D.Pea k Default
NiMH Sensitivit y
Default: 4mV/Cell
D.Pea k Default
5-15mV/Cell
Default: 4mV/Cell
NiCd Sensitivit y 5-15mV/Cell
D.Pea k Default
NiCd Sensitivit y
D.Pea k Default
Ke y B ee p O N
OFF/ON
Buzze r O N
Ke y B ee p O N
OFF/ON
Buzze r O N
Input . P owe r L ow 10.0-11.0V
Cut-Of f 1 1.0V
Input . P owe r L ow 10.0-11.0V
Cut-Of f 1 1.0V
A C M a x P owe r S et 0-100W
5 0W
A C M a x P owe r S et 0-100W
5 0W
Loa d F actor y S et
E nter
Loa d F actor y S et
E nter
Versio n
HW:1.0 0 F W : 1 .10
Versio n
HW:1.0 0 F W : 1 .10
DESCRIPTION
cont.]
DESCRIPTION
This program is for NiMH/NiCd battery only.
When the charger detects the delta peak
This program is for NiMH/NiCd battery only.
value reaches the value you set, the
When the charger detects the delta peak
charger will say the battery is fully charged.
value reaches the value you set, the
charger will say the battery is fully charged.
The beep sounds at every time t ouching
the buttons to confirm your action. T he
The beep sounds at every time t ouching
beep or m elody sounded at various times
the buttons to confirm your action. T he
during operation to a lert different m ode
beep or m elody sounded at various times
changes.
during operation to a lert different m ode
changes.
This program m onitors the voltage of i nput
battery. If the voltage drops below the value
This program m onitors the voltage of i nput
you set the operation forcibly terminated to
battery. If the voltage drops below the value
protect the input battery.
you set the operation forcibly terminated to
protect the input battery.
It is to set the max AC power of the present
channel. Once you set it, the another
It is to set the max AC power of the present
channel will take the rest.
channel. Once you set it, the another
channel will take the rest.
Press ENTER to load factory default setting.
Press ENTER to load factory default setting.
It indicates the hardware and firmware
version.
It indicates the hardware and firmware
version.
37