Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for 909 CD142L
Summary of Contents for 909 CD142L
- Page 1 INSTRUCTION MANUAL CD142L 14.4V LITHIUM-ION CORDLESS DRILL-DRIVER...
-
Page 2: Table Of Contents
CONTENTS Warranty Warranty Power Tools Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications Safety instructions Additional safety instructions for drills Additional safety instructions for the charger Additional safety instructions related to the battery pack and battery safety... -
Page 3: Introduction
Manual before using your new 909 Power Tool. Take special care to heed the Cautions and Warnings. Conforms to relevant standards Your 909 power tool has many features that will make for electromagnetic compatibility. your job faster and easier. Safety, performance, and dependability have been given top priority in the For safe operation read instruction manual. -
Page 4: Safety Instructions
General safety rules 3) Personal safety a) Stay alert, watch what you are doing and use WARNING. Read all safety warnings and all instructions. common sense when operating a power tool. Do not Failure to follow the warnings and instructions may result in use a power tool while you are tired or under the electric shock, fire and/or serious injury. -
Page 5: Additional Safety Instructions For Drills
b) Do not use the power tool if the switch does not turn b) Recharge only with the charger specified by the it on and off. Any power tool that cannot be controlled manufacturer. A charger that is suitable for one type with the switch is dangerous and must be repaired. -
Page 6: Additional Safety Instructions For The Charger
• Rags, cloths, cord, string and the like should never be left around the work area. • Your 909 tool with Lithium Ion batteries may only be charged with the specific designed 909 Lithium • Support the work properly. Ion battery charger purchased with the tool. IT IS •... -
Page 7: Additional Safety Instructions Related To The Battery Pack And Battery Safety
Do not place any object on to, or allow anything to rest on the charger. • Do not plug anything other than your 909 tool into the charger, as other objects may touch dangerous voltage • Make sure that the charger cable is positioned where... -
Page 8: When To Charge The Battery
• Charge the battery only with the 909 charger supplied • If the plastic housing of the battery pack breaks open with the tool or 909-approved replacements and or cracks, immediately discontinue its use and do not according to the instructions in the 909 Instruction recharge it. -
Page 9: Know Your Product
Know your product This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Keyless chuck 2. Handle 3. Variable speed trigger switch with electric brake 4. -
Page 10: Unpacking
Due to modern mass production techniques, it is unlikely in this manual. that your 909 Power Tool is faulty or that a part is missing. Another feature of the drill/battery pack is the low voltage If you find anything wrong, do not operate the tool until the cut out feature. -
Page 11: Battery Charging
2. Connect the power supply Battery charging from the charger adaptor (9) IMPORTANT. Before plugging in the power supply from the to the charger base (10) via charger adaptor (9) to the charger base (10) always ensure plugging the socket from the that the plug is switched off at the mains. -
Page 12: To Obtain The Best Life For The Battery
4. The battery charging time is approximately 3 – 5 hours. storage, charge between 50 and 75%. Avoid allowing lose When the red and yellow LED go out leaving the green items like screws or nails etc. to be stored with battery LED glowing the charging cycle is complete. -
Page 13: Using The Drill
Using the drill CAUTION. Do not continue to overload the drill and constantly reset the overload. Doing this will cause the Trigger switch battery cells to over heat. Use the forward/reverse switch (4) to select the direction Temperature Cut Out of rotation, then pull the trigger (3). - Page 14 For drilling, always use the use the Drill position by aligning Forward/reverse switch the Drill symbol with the triangular indicator on the front face Note. You can only change of the drill near the torque collar. the direction of rotation of the For setting the torque position, select a low setting on drill using the forward/reverse the torque collar and align the selected symbol with the...
-
Page 15: Drilling
Drilling Chuck replacement Drilling metals The chucks of reversible drills are always fixed by a screw with a left-hand thread. The screw, which is located in the • Always clamp sheet metal. centre of the chuck, must be removed before the chuck can •...