1. Manuals
  2. Brands
  3. 909 Manuals
  4. Drill
  5. DP250LS
  6. Instruction manual

909 DP250LS Instruction Manual

1/3 hp 5 speed drill press with laser
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
DP250LS
1/ 3 HP
5 SPEED
DRIL L PRESS
W I T H L ASER

Advertisement

Table of Contents
loading

Related Manuals for 909 DP250LS

Summary of Contents for 909 DP250LS

  • Page 1 INSTRUCTION MANUAL DP250LS 1/ 3 HP 5 SPEED DRIL L PRESS W I T H L ASER...

  • Page 2: Table Of Contents

    CONTENTS Warranty Power Tools Warranty Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications Safety rules for laser lights General safety instructions Additional safety rules for drill presses Unpacking Required tools Assembly time Components...

  • Page 3: Environmental Protection

    Manual before using your new 909 Power Tool. Take special care to heed the Cautions and Warnings. Specifications Your 909 power tool has many features that will make Voltage: 230–240Vac ~ 50Hz your job faster and easier. Safety, performance, and...

  • Page 4: Safety Rules For Laser Lights

    General safety rules WARNING. Read all safety warnings and all instructions. The laser light/laser radiation used in the 909 laser Failure to follow the warnings and instructions may result in system is Class 2 with maximum 1mW power and 650nm electric shock, fire and/or serious injury.
  • Page 5 3) Personal safety b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled a) Stay alert, watch what you are doing and use with the switch is dangerous and must be repaired. common sense when operating a power tool.

  • Page 6: Additional Safety Rules For Drill Presses

    b) If the supply cord is damaged, it must be replaced Make sure there are no nails or foreign objects in the by the manufacturer, its service agent or similarly qualified part of the workpiece to be drilled. persons in order to avoid a hazard. Whenever possible, position the workpiece to contact the left side of the column;...
  • Page 7 Make sure the spindle has come to a complete stop before touching the workpiece. To avoid injury from accidental starting, always turn the switch off and unplug the drill press before installing or removing any accessory attachment or making any adjustment.

  • Page 8: Unpacking

    Unpacking Due to modern mass production techniques, it is unlikely that your 909 Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified.

  • Page 9: Know Your Product

    Know your product 1. Laser light on/off switch 2. Laser aperture (x2) 3. On/off switch 4. Pulley cover 5. Base 6. Column 7. Table/Support Assembly 8. Table Lock 9. Belt (x1) 10. Belt Tension Knob 11. Keyed Chuck 12. Motor Head 13.

  • Page 10: Assembly

    6. Fit the 3 handle rods to the Assembly handle hub on the drill press 1. Place base (5) on floor. head, attach them by rotating each handle in a clockwise 2. Place column assembly (6) on base and align the 3 holes direction until tight.

  • Page 11: Adjusting The Table Angle

    Adjusting the table angle CAUTION. Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments. 1. Loosen the bolt under the table by rotating it in an anti-clockwise direction using Tighten the holes by rotating the chuck key in a clockwise a 19mm wrench.

  • Page 12: Changing The Speed Of The Drill Press

    The drill scale is a guide. Always check the depth with a 1. Remove the plug from the mains socket. measuring tool to be sure the correct depth is achieved. If 2. Loosen and remove the pulley cover screw and lift the repeated holes are required, set the setting nuts as follows.

  • Page 13: Turning On And Off

    The motor is spring loaded when the tension knob is Turning on the laser line generator loose and the motor should not need to be pushed back. Just tighten the tension knob after the belt position is set. 1. The laser line generator emits two intense narrow beams of Should the belt slip during operation, loosen the tension pure red light that intersect at...

  • Page 14: Operation

    7. Rotate the laser beam until Wood drilling it intersects the mark in the • For maximum performance, use high speed steel bits workpiece. for wood drilling. 8. Repeat the process for the • Secure the workpiece to prevent it from turning opposite side.

  • Page 15: General Inspection

    2. Remove dust and dirt regularly. Cleaning is best done General inspection with a soft brush or a rag. Regularly check that all the fixing screws are tight. They 3. Re-lubricate all moving parts at regular intervals. may vibrate loose over time. 4.

Table of Contents