Download Print this page

Beat-Sonic NDS6223EP Installation Instructions Manual

Navigation/dvd system car model: 2015 lexus rc350

Advertisement

Beat-Sonic Installation Instruction:
Product: NDS6223EP
Car Model: 2015 Lexus RC350
Disclaimer:
We are not responsible to damage, loss or injury caused from attempting or performing the DIY. Further,
the navigation and DVD lock while in motion was originally installed for safety reasons. By unlocking the
navigation and DVD lock, we are assuming that the navigation and DVD will be controlled and enjoyed
by the passenger and not by the driver. As such, are not responsible to damage, loss or injury from using
the bypass modules. Please be responsible drivers!
For additional information, contact:
info@beatsonicusa.com
About the Beat-Sonic NAV/DVD Bypass Module:
System: 100% Plug and play kit from Beat-Sonic for allowing use of factory features that would be
locked out during vehicle movement.
These plug and play module kits allow override of the lock out system equipped in your factory
Navigation/DVD system when the vehicle is in motion. Due to the fact that no modification is needed on
the factory harness and this is 100% plug and play, it is easily reversible to the original factory specs
without showing any signs that this modification was ever made.
The NDS kit provides automatic video in motion for the DVD player at all times. Navigation in motion is
activated by the steering wheel volume control buttons by pressing volume up (+), down (-), up (+),
down (-) in sequence and at normal cadence. While navigation in motion is activated, the navigation
system will temporarily lose its GPS location and the position indicator on the navigation screen will stop
moving. By default, a programmable timer will reset the navigation in motion to switch off after 3
minutes.
Navigation in motion can be switched off before the timeout period has expired by repeating the
volume control button sequence up (+), down (-), up (+), down (-).
This device is suitable for Lexus generation 7 and 8 navigation systems. The full time video in motion
feature is compatible with all navigation system features including Lexus App Suite, Enform App Suite
and energy consumption display found on hybrid models.

Advertisement

loading

Summary of Contents for Beat-Sonic NDS6223EP

  • Page 1 About the Beat-Sonic NAV/DVD Bypass Module: System: 100% Plug and play kit from Beat-Sonic for allowing use of factory features that would be locked out during vehicle movement. These plug and play module kits allow override of the lock out system equipped in your factory Navigation/DVD system when the vehicle is in motion.
  • Page 2 DIY Starts Here: 1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY. (a) Disengage the claw and disconnect the shift hole cover sub-assembly as shown in the illustration. (b) Turn the shift lever knob sub-assembly counterclockwise and remove it. 2. REMOVE INSTRUMENT PANEL FINISH PANEL END LH. (a) Using a molding remover, disengage the 3 clips in the direction indicated by the arrow (1) shown in the illustration.
  • Page 3 3. REMOVE INSTRUMENT PANEL FINISH PANEL END RH. (a) Using a molding remover, disengage the 3 clips in the direction indicated by the arrow (1) shown in the illustration. (b) Pull the instrument panel finish panel end RH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 guides and remove the instrument panel finish panel end RH.
  • Page 4 6. REMOVE CONSOLE PANEL SUB-ASSEMBLY. (a) Remove the screw. (b) Move the shift lever to N. (c) Disengage the 8 claws, clip and 4 guides as shown in the illustration.
  • Page 5 (a) Remove the 4 bolts. (b) Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips. 8. Connecting the NDS6223EP. Step#1 Once the head unit is out, look for a 59 pin connector on the “right”...
  • Page 6 Step#5 Connect the male side of the NDS6223EP connector to the female connector which was disconnected from the previous step. Make sure the connection is secure and that none of the pins are exposed on the side.
  • Page 7 GPS connector on the NDS6223EP. Then, connect the male side of the GPS connector on the NDS6223EP to the radio. (Photo shown here is actually the IS350 head...
  • Page 8 Connect the other side of the NDS6223EP connector to the factory head unit. Step#14 The default setting of the NDS6223EP is programmed to turn off automatically after 3 min. Please read the enclosed programming instruction (found inside the retail box) and program the switch to your desired setting.