Beat-Sonic SLA-91 Instruction Manual

SLA-91
＆
Lexus IS300 w/ Premium Sound
Thank you for your purchase of Beat-Sonic Sound Adapter SLA-91. ・
Please read the following instructions carefully during installation and operation.
Car Model Model Year
Lexus IS 300 w/ Premium Sound
2002-2005

Features

１． Allow plug and play installation of an aftermarket audio system.
Precautions
１． Front to rear speaker fader will be disabled.
２． Some aftermarket systems may sound a slight popping noise upon first powering
up the audio system.

Dimensions

Installation 2DIN - 40mm Width x 25mm Height x 82mm Depth

Package Contents

OEM Toyota dash panel, SLA-91 adapter, installation manual
Mount all components in locations that will not inhibit safe driving or obstruct motions of various
components of the vehicle functions. Be cautious not to damage wires, piping, tanks and other
areas as installed in the vehicle. Avoid wet, dusty or areas of extreme temperatures for installation.
Damages resulting to the vehicle of aftermarket audio system as result of inproper installations or
careless installation are not covered by any warranty, nor are we responsible for any injuries or
damages resulting from the installation process. Please observe caution when performing installation.
Beat-Sonic
14778 Beach Blvd. La Mirada, CA 90638
TEL(714) 994-1085
URL : http://beatsonicusa.com/ E-mail : info@beatsonicusa.com
. 2
Ampli er Remote Wire
Make ALL of the following
Depending on the
connections for proper operation.
manufacturer or model of
the aftermarket radio, the
reference and names of the
Amplifier Remote Trigger
Wire may differ. Please refer
to the instructions as
provided by the respective
audio unit to be installed.
*If the aftermarket radio does not come with an ampli er
remote wire, connect to the acc power.
Blue/White/Amplifier Remote Trigger(+)
SLA-91
Installation Manual
Model Chassis Code
SXE10、GXE10 、 JCE15W、JCE10W 、 GXE10W
Weight: 250g Brackets, Dash Pieces and Adapter
Aftermarket Head Unit
Front speaker Outputs
Black/Negative Ground (-)
Red/Ignition Power ACC (+)
Yellow/Battery Constant (+)
Orange/Illumination Dimmer
Blue/Antenna Remote
20 Pin OEM
20 Pin
Connector
Connector
Precautions for Installation Procedures
*Always disconnect the negative terminal of the vehicle battery before installation.
NO:000003
*Protect all wires that must be located near sharp metal parts of the vehicle.
*Check after installation that all vital features such as wipers, lights, brake lamps, etc
are in working order in addition to the installed systems.
Make sure that the original audio head unit and sound systems are in working order.
This kit is not designed to resolve issues that existed before installation.
. 1
Removal of the original head unit
1.
Remove the AC vent panel.
（4 clips and 2 screws)
2.
Accessory panel is removed
（2 clips）
3.
OEM Audio unit is removed。
（4 Bolts）
. 3
Installation of aftermarket audio head unit
1.
Attach the factory carrier main brackets as shown
using 6 screws on each side supplied by the aftermarket
head unit.
2.
Install the aftermarket head unit to the
appropriate location as shown
reusing factory 4 bolts.
3.
Mount the dash piece included with the kit as shown.
4.
Double check to make sure the new dash piece is connected securely.
Additional Notes
The dash panel (included with the kit)
is mounted as shown on the right.
Pay special attention to the
mounting point as circled to the right.
. 4
Testing the new audio system.
Check that all components function as well as all electrial functions of the vehicle.
ネジ （6）
Bracketー(L)
Included with the kit
H/U
Top View
Screws (2 )
Cl i p s (4)
AC Vent Panel
Cl i p s (2)
Acc case
TRC（SNOW） Button
Bolts （4）
OEM Audio Unit
Bracketー(R)
Bolts （4）
TRC
OFF
*If equipped, please installal the appropriate
button as shown.
H/U
Panel
Panel