Table of Contents
Advertisement
LCPRO-3 and LCPRO-4
LOW CURRENT
REMOTE START SYSTEM
CONGRATULATIONS on your choice of a PRO Start™ Remote Engine Starter and Keyless Entry by Crimestopper
Security Products Inc. This system is designed to work on new vehicles with a Canbus computer system. It has a
Data Port for both Smart Phone interface and a Bypass module to interface with the vehicle computer. These
modules are not included; consult your dealer for availability. This booklet contains the information necessary for
operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products
Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, and Brake Reset. For programming, the program button is required.
-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing
dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features may also
require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be
installed with your particular system.
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV A 07-2014
OPERATING INSTRUCTIONS
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation.
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
The manufacturer is not
Advertisement
Table of Contents
Related Manuals for CrimeStopper Pro Start LCPRO-3
Summary of Contents for CrimeStopper Pro Start LCPRO-3
- Page 1 REMOTE START SYSTEM OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a PRO Start™ Remote Engine Starter and Keyless Entry by Crimestopper Security Products Inc. This system is designed to work on new vehicles with a Canbus computer system. It has a Data Port for both Smart Phone interface and a Bypass module to interface with the vehicle computer.
-
Page 2: Table Of Contents
OPERATION CAUTIONS & WARNINGS CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle linkage, and all engine safety features, are in perfect working condition. -
Page 3: Using The Remote Transmitter
USING THE REMOTE TRANSMITTER VEH 1 = Blue LED VEH 2 = Red LED AUX Outputs thru Data (LCPRO-4 only) AUX 1 = Trunk + Lock AUX 2 = Trunk + Unlock AUX 3 = Trunk + Start AUX 4 = Lock + Start (Requires Canbus Data Module) LCPRO-3 LCPRO-4... -
Page 4: Status Led
STATUS LED STATUS LED: Used for Remote Start Diagnostics – page 14 (Optional, requires Installation of LED) LED will flash when locking your doors with remote. LED will remain solid in Valet Service Mode. REMOTE ENGINE CONTROL REMOTE START & TRUNK POP – Button Press Selection (Option # 6): To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for button press selection. - Page 5 REMOTE ENGINE CONTROL REMOTE ENGINE STARTING – UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2 and 3 time.
- Page 6 REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle will remain running for the programmed time or until canceled. The Run Time choices are: 10, 20, 30 minutes or Infinity Run.
- Page 7 REMOTE ENGINE CONTROL SELECTABLE HOURLY COLD-START MODE (1-4 HOURS) This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. TIMED SELF-START MODE –...
-
Page 8: Turbo Timer Mode
TURBO TIMER MODE (Option 22) The optional Turbo Timer mode allows the ProStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cool-down without the need for expensive turbo timers. -
Page 9: Manual Transmission Mode
MANUAL TRANSMISSION MODE (Option 11) MANUAL TRANSMISSION EXIT PROCEDURE (Option #11-1, 11-3 & 11-4) This system features a Manual Transmission Mode. When exiting the vehicle, there is safety check out procedure required for the manual transmission mode to work. There are 3 choices of operation, 1. -
Page 10: Convenience And Safety Features
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (Power Door Locks, may require Data Module - Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. -
Page 11: Convenience And Safety Features
This feature only works on newer CANBUS vehicles using a Data Module that supports this feature. With this option you can use both the OEM and Crimestopper remote. The databus module may require custom programming to enable this feature. Consult with your installer. -
Page 12: Transmitter Programming
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The LCPRO-3 & LCPRO-4 learns up to 4 different transmitter codes. 1. Turn Ignition Key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. -
Page 13: Vehicle Operation (Blue Or Red Led)
2-VEHICLE OPERATION & PROGRAMMING A single Remote Control can control two different vehicles. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 12) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. -
Page 14: No Factory Keyless Entry After Remote Start
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. -
Page 15: Battery Replacement
BATTERY REPLACEMENT To Replace the Battery: The Remote Control uses two CR-2025 Lithium 3 Volt Batteries. Simply remove the Phillips screw located behind key ring (see diagram below). The top cover snaps apart from the back cover. Slide old batteries out and remove plastic cover. -
Page 16: 2-Way Data Port
Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. This Crimestopper system has a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module.