Related Manuals for Advantech CompactPCI MIC-3021/8
Summary of Contents for Advantech CompactPCI MIC-3021/8
- Page 2 All other product names or trademarks are properties of their respective owners. The MIC-3021/8, developed by Advantech CO., LTD., has passed the CE test for environment specification when shielded cables are used for external wiring. We recommend the use of shielded cables.
- Page 4 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 5 If any of these items are missing or damaged, contact your distributor or sales representative immediately. If you have any technical questions about the MIC-3021/8 or any other Advantech products, please visit our support website at: • http://www.advantech.com.tw/support For more information about Advantech's products and sales informa- tion, please visit: •...
- Page 6 Contents 1.1 Introduction ..............2 1.2 Features ................. 3 1.3 Specifications ..............4 1.3.1 General ................4 1.3.2 Fan Tray Module ............4 1.3.3 ATX Power Supply (MIC-3021/8-7A) ......5 1.3.4 Redundant Power Supply (MIC-3021/8-7R) ....5 1.4 Dimensions ..............6 2.1 Initial inspection ............
- Page 7 Figures...
- Page 9 The MIC-3021/8 is a 6U 8-slot CompactPCI enclosure for rack or panel mounting. It has eight 6U card slots, and has a device bay which can accommodate devices and peripherals such as floppy disk drives and hard disk drives. Its rugged construction and flexible modular design allows users to configure it to meet the requirements of individual applications.
- Page 10 • Eight 6U card slots • Easy rackmount or panelmount installation • Provides ATX power supply or redundant power supply • Device bay accommodates up to four devices, including three 5.25" and one 3.5" FDD, secured by a lockable door •...
- Page 11 • Construction: Aluminum frame and galvanized sheet steel • Device bay: Accommodates up to four devices, including three 5.25" drives and one 3.5" floppy disk drive, front removable • 12-slot space (48 TE), incl. 7 CompactPCI slots and one system slot. •...
- Page 12 • Input: 90 ~ 135 or 180 ~ 265 V @ 47 ~ 63 Hz, switchable • Output: +3.3 V @ 20 A, +5 V @ 42 A, +12 V @ 14 A, -12 V @ 1.0 A • Minumum load: +3.3 V @ 0.3 A, + 5V @ 2 A, +12 V @ 1 A •...
- Page 15 We have carefully inspected the MIC-3021/8 mechanically and electrically before shipping. It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the MIC-3021/8, check it for signs of shipping damage (damaged box, scratches, dents, etc.). If it is damaged or if it fails to meet specifications, notify our service department or your local representative immediately.
- Page 16 The MIC-3021/8 is designed to be installed and maitained easily. The following illustrations show the components on the front and rear side of the enclosure. Power On/Off Switch System Slot Alarm Reset Switch Drive Bay Fan Tray Power Supply...
- Page 17 Optional system alarm and monitor module I/O Power supply switch...
- Page 18 The CompactPCI connectors are firm and rigid, and require careful handling while plugging and unplugging. Improper installation of a card can easily damage the backplane of the chassis. The system card can be installed only in the system slot. The CompactPCI specification allows the system slot to be at any position in the backplane.
- Page 19 5. Pull the upper handle down and lift the lower handle up to push the card into place. 6. Secure the card by locking the handles in place. Keep your fingers away from this area. 1. Unscrew the screws on the card front panel. Release the locking latches on the handles.
- Page 20 Before operating your system, first check your power supply source. Adjust the switch on the power supply to the correct voltage. Two mounting flanges are included for users who would like to install the MIC-3021/8 on a 19" rack or on a panel. These flanges can be installed on the front side for rack mounting or on the rear side for panel mounting.
- Page 21 3.5" hard disk drive extension brackets (3.5" to 5.25") are required. These extension brackets are available in PC shops, or users can contact an Advantech distributor to order them. An additional pair of mounting brackets are included in the MIC-3021/ 8's package.
- Page 22 Advantech recommends the device bay of the MIC-3021/8 to be configured as one 3.5" floppy disk drive, two 5.25"hard disk drives (in removable rack), and one 5.25" CD-ROM drive. Please refer to Figure 2-4 for illustration. CD-ROM Removable Rack Power Supply...
- Page 23 Follow the procedures below to install a 3.5" floppy disk drive on the top tray: 1. Fasten one pair of mounting brackets to both sides of a 3.5" floppy disk drive. Note that the guide edge of the mounting brackets should be at the lower side.
- Page 24 Follow the procedures below to install a 5.25" drive: 1. Fasten one pair of mounting brackets to both sides of a drive. Note that the guide edge of the mounting brackets should be at the lower side. 2. Open the door of the device bay. Unfasten and remove the cover plate of the device tray.
- Page 25 One device space is available next to the fan tray module in the MIC- 3021/8, which can be used for installing a 5.25" device. One pair of mounting brackets without guiding flange are included for mounting the device. Since the brackets are not guided, we recommend that users install only a half-height device such as a CD-ROM or a remov- able drive mount.
- Page 26 The fan tray module of MIC-3021/8 is designed to be "hot-swappable", i.e., users can remove and install the fan tray without turning off the system power. Follow the steps below to replace a fan tray: 1. Unfasten the fan tray. 2.