Page 2
PCI Industrial Computers Manufacturers Group. All other product names or trademarks are properties of their respective owners. CE Notification The MIC-3041L, developed by Advantech Co., Ltd., has passed the CE test for environment specifications when shielded cables are used for external wiring. We recommend the use of shielded cables.
Page 3
Product warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Page 4
If any of these items are missing or damaged, contact your distributor or sales representative immediately. Technical Support and Sales Assistance If you have any technical questions about the MIC-3041L or any other Advantech products, please visit our support website at: • http://www.advantech.com.tw/support...
Page 6
Figures Figure 1-1: MIC-3041L dimensions ................4 Figure 1-2: Appearance of MIC-3041L................. 5 Figure 2-1: Front view of MIC-3041L ..............7 Figure 2-2: Removable parts of MIC-3041L ..............8 Installing a card into the chassis Figure 2-3: .............9 Figure 2-4: ............10 3.5” Hard Disk Drive and cable location Figure 2-5: Hot swappable fan maintenance ............11 Figure 3-1: MIC-3803/MIC-3805 Backplane slot numbering ........
The built-in high quality backplane with 64 bit / 66MHz bus speed offers best impedance control, meets open architecture standards and is compatible with all Advantech CompactPCI boards. The MIC-3041L supports build-in on-board IDE, floppy and USB connectors for cost-effective solution.
1.2 Features Four 6U card slots Supports front and rear I/O Supports H.110 CT application or non-CT application Two IDE storage devices 300W ATX power supply with PFC Hot-swap compliant backplane A hot-swap fan module Integrated intelligent management module, 968A390021 (also call MIC-3924L-A), which can detect the chassis temperature and fan speed.
1.3.3 Power Supply Input: 100~240 V AC @ 50~60 Hz with auto switching capability -- PFC (Power Factor Correction). Output (per module): 300W, +3.3V,+5V,+12V total output power shall not exceed 280W Maximum load: +3.3V @ 28A, +5V @ 30A, +12V @ 15A, -5V @0.3A, -12V @ 0.8A, +5Vsb @ 2.0 A Minimum load: +3.3 V @ 0.3 A, + 5V @0.1 A, +12 V @ 0 A, -12V @0A MTBF: 100,000 hours @ 25°...
2.1 Initial Inspection We have carefully inspected the MIC-3041LL mechanically and electrically before shipping. It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the MIC-3041L, check it for signs of shipping damage (damaged box, scratches, dents, etc.).
Figure 2-2: Removable parts of MIC-3041L 2.3 Installation Procedures 2.3.1 Card Installation and Removal The CompactPCI™ connectors are firm and rigid, and require careful handling while plugging and unplugging. Improper installation of a card can easily damage the backplane of the chassis. The system card can be installed only in the system slot.
Push the card into the slot gently by sliding the card along the card guide until the handles meet the rectangular holes of the cross rails. Please refer to figure 2-3. Figure 2-3: Installing a card into the chassis Note: If the card is correctly positioned and has been slid all the way into the chassis, the handles should match the rectangular holes.
2.3.3 Installing a 3.5” Hard Disk Drive Follow the procedures to install 3.5" hard disk drives in the MIC-3041L: 1. Remove the top plate. 2. Mount the HDD on the HDD rack with screws. 3. Connect the IDE cable to the HDD. 4.
Note: (1) RIO-3309C/RIO-3309L only has one IDE channel, thus the IDE CD-ROM is connected to “USB to IDE” daughter board. (2) Please use Windows 2000 SP4 for USB driver installation. If neither CPU board nor RIO have PS/2 port, please use Com port mouse with USB keyboard to copy USB 2.0 driver to floppy or HDD for USB 2.0 driver installation.
3.1 General Information There are two kinds of backplanes for MIC-3041L series. MIC-3803 is backplane with H.110 CT bus, and MIC-3805 is backplane without H.110 CT bus. Both backplanes provide four CompactPCI™ slots. One slot is assigned to the CPU board and the other slots for three peripheral boards.
Page 20
circles or triangles. Slot5 of MIC-3803 and MIC-3805 marked by a triangle, is the system slot and can only be used by a CPU board. The other slots are peripheral slots. The logical number of each slot is defined according to the IDSEL signal and the associated address used to select the slot.
Figure 3-1: MIC-3803/MIC-3805 Backplane slot numbering 3.5 Connector and Jumper Locations The backplane provides connectors and jumpers for users to configure the backplane for specific application. Table 3-2 gives a brief description to each connector on the backplane. Figure 3-3 to Figure 3-6 illustrate the connector locations of the backplane.
** JP2 is used to set 64EN for physical slot 2,JP3 is used to set 64EN for physical slot, JP4 is used to set 64EN for physical slot 4. *** If one turns the four dip switch to the left hand side, than he can use the USB on the RIO and the USB on the backplane will be off.
+3.3V +3.3V VIO for +5V VIO for +3.3V Figure 3-3: V I/O voltage selection 3.5.4 Fan Module Connector The FAN connectors provide +12 V power for fan operation and accepts the tachometer output from the fans. 3.5.5 LED Status Connector This connector provides digital outputs for the alarm module (MIC-3924L-A).
Page 28
A.4 MIC-3803 and MIC-3805 System Slot P4 Connector Table A-4: MIC-3803 and MIC-3805 system slot P4 connector 12-14 Key Area MIC-3041L User Manual --- Page 22...
Page 29
A.5 MIC-3803 and MIC-3805 System Slot P5 Connector Table A-5: MIC-3803 and MIC-3805 System slot P5 connector USBD1- USBD1+ USB_OC0# USB_OC1# MIC-3041L User Manual --- Page 23...
Page 36
A.12 Fan Module Connectors Table A-9: Fan Module Connectors Assignment +12V Fan speed A.13 ATX Power Connector (ATX1) Table A-10: ATX Power Connector Signal Signal +3.3V +3.3V +3.3V -12V PSON# FAL# IPMBPWR +12V A.14 LED board connector Table A-11: LED board Connector Signal Signal +3.3V...
Page 37
A.15 Alarm board Interface connector Table A-15: Alarm Board Interface Connector MIC-3803 MIC-3805 Signal Signal Signal Signal + 5V +12V + 5V +12V + 5V IPMB power + 5V IPMB power + 5V + 5V Fan Speed5 Fan Speed5 + 5V SMB-SDA + 5V SMB-SDA...
Appendix B Ordering Information MIC-3041L User Manual --- Page 34...
Page 41
MIC-3041L-TA: 4U-high CompactPCI™ enclosure with 4-slot non-CT backplane (MIB-3805), hot swappable cooling fan modules, and 300W ATX power supply. MIC-3041L-CA: 4U-high CompactPCI™ enclosure with 4-slot CT backplane (MIB-3803), hot swappable cooling fan modules, and 300W ATX power supply Recommend 6U CompactPCI™ SBC: User can refer to below table for the SBC and RIO accommodation.