DSC PC4000 System Manual page 22

User Functions Command
[ ]+[6]+[Access Code]
Enter [ ][6][Access Code] and then use the [<][>] keys
to display the items of the function menu. Press [ ] to
select an item.
[0] Quick Arm
[1] Quick Exit
[2] Auto Arm Control
[3] Keypad Setup
[4] Bell / Comm Test
[5] Door Chime
[6] Spec. Messages
[7] User Call Up
[8] View Partitions
Item [0], [1], [5] and [6] turn on and off various functions.
To enable or disable these functions, press the [ ] key
to toggle "Y "or "N" on the keypad.
Y - The function is enabled
N - The function is disabled
Quick Arm
[ ]+[6]+[Access Code]+[0]
The "Quick Arm" feature is enabled by toggling to "Y"
on the keypad. When enabled the panel can be armed
by entering [ ][0]. Users with a One Time Use access
code should not use this feature because the OTU code
is only erased when used to arm.
Quick Exit
[ ]+[6]+[Access Code]+[1]
The "Quick Exit" function is enabled by toggling to "Y"
on the keypad. When enabled the user can exit through
any delay zone without altering the status of the system,
by entering [ ]+[0] on the keypad while the system is
armed.
Auto Arm Control
[ ]+[6]+[Access Code]+[2]
The Auto Arm Control options can only be accessed if
Auto Arm is enabled for the partition. The PC4000 can
be programmed to arm a partition at the same time
each day, by enabling the Auto Arm function and
programming the Auto Arm time.
At the selected Auto Arm time, the system will give a
pre-alert. The keypad buzzer begins to sound and the
Bell/Siren will pulse once every 10 seconds to alert
anyone on the premises that the system is about to arm.
The Bell/Siren pulse can be programmed to be silent.
The keypad buzzer will sound for one minute before
Auto Arming unless the Auto Arm is aborted. To abort
the Auto Arm and silence the keypad press any key
during the pre-alert. The Auto Arm will be attempted at
the same time the following day. The PC4000 can be
programmed to require a code to be entered for a user
to abort the Auto Arm.
Upon selecting the Auto Arm Control function, the Auto
Arm Control menu will appear on the LCD keypad.
[0] Auto Arm [1] Auto Arm Time
Auto Arm toggles "Y" or "N" to enable or disable the
Auto Arm function.
Auto Arm Time is the time the partition will automatically
arm itself every day.
NOTE: The Auto Arm time is a 24 hour clock and times
must be entered as two digit numbers.
E.g. HH - 01, 02,.....10,11,.....23,24
MM - 00, 01,.....35,36.....58,59
Enter 4 digits representing the time in hours and minutes
(HH:MM) based on 24 hour or military time. Always enter
a leading zero where only one digit is required, 8:05 am
would be entered as 0805, 1:30 pm would be entered as
1330.
Keypad Setup
[ ]+[6]+[Access Code]+[3]
This function allows the user to adjust the backlighting
and contrast of the LCD-4500 keypad. When this
function is selected, the Keypad Setup menu will appear
on the keypad.
Bright Control adjusts the level of backlighting on
the LCD display and the backlighting on the keys.
Contrast Control adjusts the contrast of the lettering
on the LCD display.
Use the [<][>] keys to toggle through the eight different
settings, and press [ ] to select the level of preference.
Bell / Comm Test
[ ]+[6]+[Access Code]+[4]
This option allows the end user to test the system. This
option activates all outputs programmed for 'Fire and
Burg', 'Inv Fire/Burg', 'Burg Only' and 'Inv Burg Only' for
two seconds, sounds the keypad's for 2 seconds, tests
the main board battery voltage and sends a test code
transmission to the monitoring station.
Door Chime
[ ]+[6]+[Access Code]+[5]
The Door Chime feature is enabled or disabled on a
partition by pressing the [ ] key to toggle from "N" to
"Y" or "Y" to "N". When the door chime feature is
enabled, any zone that has been selected as
chimeable will cause the keypad to beep 5 times each
time the zone opens or restores while the partition is
disarmed (Note that Fire zones and 24 hour zones are
never disarmed, therefore they can never chime).
See "Chime Function" in the Programming Manual to
enable a zone to use the chime function. While
disarmed zone bypass may be used to eliminate the
beeping.
20