Connecting Audio Components - Marantz ZR6001 User Manual

CONNECTING AUDIO COMPONENTS

CD RECORDER / MD DECK
DIGITAL OUT
OUTPUT
OUT IN
DIGITAL DIGITAL
L R
L L INPUT OUTPUT
R R
L R R L
FM FM ( ( 75 75Ω Ω ) ) GND GND AM AM
VIDEO VIDEO
TV TV DVD DVD VCR1 VCR1
IN IN
DIGITAL IN DIGITAL IN DIGITAL IN DIGITAL IN
3 3 4 4
1 1 1 1 2 2
TV TV DVD DVD VCR1 VCR1
L L
R R
IN IN
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal
which is currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CD PLAYER
OUT IN
L
L L
R
R R
L R
L R
L R L R L R
ANTENNA ANTENNA COMPONENT VIDEO COMPONENT VIDEO
INPUT-1 INPUT-1 INPUT-2 INPUT-2 MONITOR OUT MONITOR OUT
Y Y C C B B / / C C R R / / Y Y C C B B / / C C R R / / Y Y C C B B / / C C R R / /
P P B B P P R R P P B B P P R R P P B B P P R R
S-VIDEO S-VIDEO
VCR1 VCR1 DSS/VCR2 DSS/VCR2
MONITOR MONITOR
DSS/VCR2 DSS/VCR2 MONITOR MONITOR
TV TV DVD DVD IN IN OUT OUT IN IN OUT OUT OUT OUT
OUT OUT IN IN OUT OUT OUT OUT
MULTI MULTI
RC-5 RC-5
DIGITAL OUT DIGITAL OUT RC RC L L SL SL SBL SBL C C
IN IN
COAX. COAX.
RS-232C RS-232C FLASHER FLASHER
PRE PRE
IN IN
OUT OUT
OPT. OPT. OPT. OPT.
OUT OUT
R R SR SR SBR SBR SW SW
DSS/VCR2 DSS/VCR2 CD CD CD CD TAPE TAPE TAPE TAPE CDR/MD CDR/MD CDR/MD CDR/MD MULTI MULTI L L SL SL SBL SBL C C
7.1CH 7.1CH
IN IN
OUT OUT IN IN OUT OUT IN IN IN IN OUT OUT OUT OUT IN IN IN IN OUT OUT OUT OUT OUT OUT R R SR SR SBR SBR SW SW
AUDIO AUDIO AUDIO AUDIO ( ( AUX2 AUX2) )
R L R L
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and 2
optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These
jacks can be connected to a CD recorder-, or a
MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source's connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2
input jacks. Use 75 ohms coaxial cables (for
digital audio or video) for DIG-3, 4 input jacks.
• You can designate the input for each digital
input/output jacks according to your component.
See page 20.
TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
15