Connecting Audio Components - Marantz SR5300 User Manual

CONNECTING AUDIO COMPONENTS

CD RECORDER / MD DECK
OUT IN
DIGITAL DIGITAL
L L OUTPUT
R R
L R R L
The output audio signal from the TAPE OUT jack and the CD-R/MD
OUT jack is the sound source currently selected.
CAUTION
• Do not connect this unit and other components to mains power
until all connections between components have been
completed.
NOTES
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R(right) channel, and white
connectors are for the L(left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected
with this unit.
• Do not bind audio/video connection cables with power cords
and speaker cables will result in generating hum or other noise.
DIGITAL
OUT
OUTPUT
L
R
L R
INPUT
L R
DIGITAL DIGITAL
IN / OUT IN / OUT
PRE
OUT FRONT
ANTENNA SURR.
DIG - 4 IN DIG - 4 IN
SURR.
CENTER
CENTER
AM
DIG - 3 IN DIG - 3 IN
SUB SUB
WOOFER WOOFER
GND DIG.OUT COAX DIG.OUT COAX
CENTER
SURR.
CENTER
DIG - 2 IN DIG - 2 IN
FM
(75Ω)
SURR.
DIG - 1 IN DIG - 1 IN
FRONT
6.1CH
INPUT
L R DIG.OUT OPT DIG.OUT OPT
CD PLAYER
L R
L R L R
L L R R
CD CD
OUT OUT
TAPE TAPE MONI
MONITOR
TOR
OUT OUT
VCR1 VCR1
TAPE TAPE
L L R R
CDR CDR
DSS / DSS /
CDR CDR
/ MD / MD
VCR2 VCR2
/ MD / MD
VCR1 VCR1
VCR1 VCR1 VCR1 VCR1
DSS / DSS /
DSS / DSS / DSS / DSS /
VCR2 VCR2 VCR2 VCR2 VCR2 VCR2
TV TV TV TV
IN IN OUT OUT
DVD DVD DVD DVD
IN IN IN IN
S - VIDEO
REMOTE CONTROL REMOTE CONTROL AUDIO AUDIO VIDEO
L R L R
CONNECTING DIGITAL AUDIO COMPONENTS
• There are four digital inputs, two coaxial jacks and two optical jacks,
on the rear panel. You can use these jacks to input PCM, Dolby
Digital and DTS bitstream signals from a CD, DVD, or other digital
source components.
• There are one digital output with coaxial jack and one with optical
jack on the rear panel. These jacks can be connected to CD
recorder, MD deck.
• Setup the digital audio format of DVD player, or other digital source
component. Refer to the instructions for each component to be
connected to digital input jacks.
• Use fiber optical cables(optical) for DIG-1,2 input jacks. Use 75
ohms coaxial cables(for digital audio or video : optical) for DIG-3,4
input jacks.
• You can designate the input for each digital input/output jacks
according to your component. See page 16.
NOTES
• There is no Dolby Digital RF input jack. Please use an external
RF demodulator Dolby Digital decoder when connecting the
Dolby Digital RF output jack of the video disc player to the
digital input jack.
• The digital signal jacks on this unit conform to the EIA
standard. If you use a cable that does not conform to this
standard, this unit may not function properly.
• Each type of audio jack works independently. Signals input
through the digital and analog jacks are output through the
corresponding digital and analog jacks, respectively.
11
TAPE DECK
OUT IN
L L
R R
L R
L R
R L
FRONT
SURROUND
SWITCHED
ANALOG AUDIO
100W MAX
SURR.CENTER CENTER
AC OUTLET
SPEAKER SYSTEMS
(230V
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
MODEL NO. SR5300
AC IN
50Hz)