Connecting Audio Components - Marantz SR5500 User Manual

Caution:
• Be sure to use speakers with the specified
impedance as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
s p e a k e r w i r e s
touch each other
and do not let them
touch any metal
part of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an electric shocks.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
• Be sure to connect the positive and negative
cables for the speaker properly. If they are miss-
connected, the signal phase will be reversed and
the signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in).
If your subwoofer is a passive type (power
amplifier is not built in), connect a monaural power
amplifier to the PRE OUT SUBWOOFER jack and
connect the subwoofer to the amplifier.
12
SR5500U DFU_01_ENG 1_2
Page 12

CONNECTING AUDIO COMPONENTS

CD RECORDER / MD DECK
DIGITAL OUT
OUTPUT
L
R
OUT IN
DIGITAL DIGITAL
L R
L L INPUT OUTPUT
R R
L R R L
ANTENNA
FM (75Ω) GND AM
VIDEO
TV DVD VCR1 DSS/VCR2 MONITOR
IN OUT IN OUT
DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT
3 4 4 COAX.
RS-232C
1 1 2 OPT. OPT.
TV DVD VCR1 DSS/VCR2
L L
R R
IN OUT IN OUT
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal
which is currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
TAPE DECK
CD PLAYER
OUT IN
L L
R R
L R
L R
ANALOG AUDIO
L R L R L R
DIGITAL AUDIO
COMPONENT VIDEO (COAXIAL)
INPUT-1 INPUT-2 MONITOR OUT
C C C C C C
Y B P / B R / P R Y B / P B R P / R Y B / P B R / P R
S-VIDEO
VCR1 DSS/VCR2 MODE
MONITOR
DIGITAL AUDIO
TV DVD IN OUT IN OUT OUT
OUT
(OPTICAL)
MULTI
RC-5
RC L SL SBL C
IN
PRE
OUT
OUT
R SR SBR SW
CD CD TAPE TAPE CDR/MD CDR/MD MULTI L SL SBL C
7.1CH
IN
IN IN OUT OUT IN IN OUT OUT OUT R SR SBR SW
AUDIO AUDIO (AUX2)
R L R L
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and 2
optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These
jacks can be connected to a CD recorder-, or a
MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source's connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2
input jacks. Use 75 ohms coaxial cables (for
digital audio or video) for DIG-3, 4 input jacks.
• You can designate the input for each digital
input/output jacks according to your component.
See page 18.
Adobe PageMaker 6.5J/PPC
04.8.2, 4:12 PM
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.