Connecting Audio Components - Marantz SR9600U User Manual

Caution:
• Be sure to use speakers with the specified impedance
as shown on the rear panel of the SR9600.
• To prevent damage to circuitry, do not let the bare
speaker wires touch
each other and do
not let them touch
any metal part of
the SR9600.
• Do not touch the
speaker terminals
when the power is
on. It may result in
an electric shock.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage the
SR9600.
Note:
• Be sure to connect the positive and negative cables
for the speaker properly. If they are misconnected,
the signal phase will be reversed and the signal
quality will be corrupted.
22
SR9600U DFU̲01̲ENG 3̲4 Page 22
All manuals and user guides at all-guides.com

CONNECTING AUDIO COMPONENTS

CD RECORDER / MD DECK
OUT IN
DIGITAL DIGITAL
INPUT OUTPUT L L
R R
L R R L
L R L R
7.1CH IN
L SL SBL C L
DIGITAL DIGITAL
IN IN
(AUDIO)
1 1
S400
SR SBR SW
2 R
(AUX 2)
L
3
AUDIO
S400
R
4
DVD LD TV DSS
5 5
VIDEO
6
S-VIDEO
7
INPUT-1
(DVD)
HDMI
Ver 1.1
8
INPUT-1 (DVD) INPUT-2 (DSS)
COMPONENT
C B / C R / C B /
OPT OPT VIDEO Y P P Y P
B R B
1 3 1
COAX
2 4 2
DIGITAL DIGITAL
OUT
OUT
USB AUDIO RS232C DC OUT
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal which
is currently selected.
Caution:
• Do not connect the SR9600 and other components
to a power outlet until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect inputs and outputs properly.
• Refer to the instructions for each component that
is connected to the SR9600.
• Do not bind audio/video connection cables with
power cords and speaker cables. This will result in
a hum or other noise.
CD PLAYER
DIGITAL
OUT OUT IN
OUTPUT
L L L
R R R
L R
L R
L R
L R L R L R
MAIN IN MULTI OUT
R SL SR SBL SBR C A B
L
CENTER
R
SPEAKER C
PRE OUT SW AUDIO
ON SURR.BACK
OFF /MULTI SPK.
/SPK. C
LEFT
SURR.BACK
/MULTI SPK.
/SPK. C
RIGHT
IN IN TAPE TAPE OUT OUT IN CD-R / MD OUT IN CD-R / MD OUT CD CD
VCR-1 VCR-2 / DVD-R MONITOR OUT
TUNER-1
IN OUT IN OUT 1 2
AM GND FM(75Ω)
MULTI OUT
A B
TUNER-2
AM GND FM(75Ω)
VIDEO
OUTPUT
INPUT-2
C B / C R /
(DSS) Y P P
B R
OUTPUT-1
INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R)
CLASS 2 WIRING
SWITCHED 1A 120W MAX
FRONT A OR B, CENTER, SURR,
SURR BACK
FRONT A AND B : MINIMUM 8 OHMS
C R / C B / C R / C B / C R /
P Y P P Y P P OUTPUT-2
R B R B R
UNSWITCHED 1A 120W MAX
3
IN MODEL NO. SR9600
IR
FLASHER RECEIVER
IN IN
4 OUT
AC 120V 60H Z
EMITTER OUT RC-5 MULTI RC
AC OUTLETS
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 8 digital inputs, 4 coaxial jacks and 4
optical jacks on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source component.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These
jacks can be connected to CD recorder, or MD
deck inputs, respectively.
• Refer to the instructions for each component to
setup the digital audio format of a DVD player, or
other digital source connected to digital input
jacks.
• Use 75 ohm coaxial cables (for digital audio or
video) for the DIG-1, 2, 3, 4 input jacks. Use
fiberoptic cables (optical) for the DIG-5, 6, 7, 8
input jacks.
• You can designate the input for each set of
digital input/output jacks according to your
component. (see page 33)
05.4.27, 5:40 PM
TAPE DECK
ANALOG AUDIO
FRONT A
LEFT
FRONT A
RIGHT
DIGITAL AUDIO
(COAXIAL)
FRONT B
LEFT
FRONT B
DIGITAL AUDIO RIGHT
(OPTICAL)
SURR.
LEFT
SURR.
RIGHT
SPEAKER SYSTEMS
: MINIMUM 6 OHMS
AC IN
Notes:
• There is no Dolby Digital RF input jack. Use an
external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the videodisc player to the digital input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
Adobe PageMaker 6.5J/PPC