7.1 Ch Input Level; Multi Plc Setup - Marantz ZR6001 User Manual

LEVEL (VOLUME LEVEL):
Adjust the Multi-speaker output level with
cursor button.
Note:
• This setting can be changed when the Surr Back is
set "NONE" in 2-1 SPEAKER SIZE menu.
When this setting is unavailable, "✽✽✽" is
displayed
MAIN ROOM STATUS:
Selected input source in the main room will be
displayed.
Note:
• If "VOLUME" is set to "FIXED", the multi-room
output level cannot be adjusted from the second
zone.
After you complete this portion of the set up, move
the cursor to "MAIN" with or cursor buttons and
press ENTER button.
24

8 7.1 CH INPUT LEVEL

or
This sub-menu is to adjust the speaker levels for
7.1-channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
8 7 . 1 CH I N P U T L E V E L
V I D EO I N :
F RON T L :
C E N T ER :
F RON T R :
S URR . R :
S URR . B R :
S URR . B L :
S URR . L :
S UB W :
MA I N
1.
Select "7.1CH INPUT" in the SETUP MAIN
MENU with the or cursor buttons, and
press the ENTER button.
2.
To select "VIDEO IN", press
button.
3.
Using the or cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
or cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔
AUX1 ↔ V-OFF ↔ LAST ↔
Notes:
• When select LAST, the source is set previous
source before 7.1 CH INPUT function is activated.
• When select V-OFF, no signal is emitted from
monitor out terminal.
4.
To Select desired channel , press the
cursor buttons.
5.
Using the or cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to "MAIN" with the
cursor buttons and press the ENTER button.
Notes:
• These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH.SEL button of the remote controller.

9 MULTI PLC SETUP

This submenu is for setting up the Multi PLC
feature of the ZR6001.
9 MU L T I P L C
MU L T I P L C S E R V E R : ON
CONN E C T I ON MOD E :
AU T O
L A S T
H I GH AUD I O QUA L I T Y
0 d B
H I GH R E L I AB I L I T Y
0 d B
0 d B
GP I D S E T T I NG : S T AR T
0 d B
0 d B
MA I N
0 d B
0 d B
1.
0 d B Select "9. MULTI PLC" in the SETUP MAIN
E X I T MENU with the or
press the ENTER button.
2.
To select desired contents, press
cursor button.
or cursor
MULTI PLC SEVER:
Select "ON" or "OFF" with the
to turn the Multi PLC Server feature ON/OFF.
CONNECTION MODE:
Select the Connection Mode of the Multi PLC
feature with the / cursor buttons.
The available Connection Modes are:
- AUTO :Normal mode
Use this mode as standard.
- HIGH AUDIO QUALITY(H-AQ)
:Emphasizes audio quality.
or
Use this mode to listen to high audio quality.
(However, when multiple ZC4001 units are
connected, audio may be lost or noise may
occur in a ZC4001 that experience poor
reception.)
- HIGH RELIABILITY(H-R)
or
:Emphasizes reliability.
Use this mode when multiple ZC4001 units are
connected, audio is lost, or noise occurs.
GP-ID SETTING
To set a Group ID, connect the AC power cables of
the ZR6001 and ZC4001 to wall power outlets as
close to each other as possible.
Set the Group ID simultaneously for the ZR6001
and ZC4001.
<ZR6001>
Using the OSD menu system, set "GP-ID
SETTING" to "START".
ZR6001 ON SCREEN DISPLAY MENU SYSTEM ZR6001 ON SCREEN DISPLAY MENU SYSTEM ZR6001 ON SCREEN DISPLAY MENU SYSTEM ZR6001 ON SCREEN DISPLAY MENU SYSTEM ZR6001 ON SCREEN DISPLAY MENU SYSTEM
9 MU L T I
E X I T
MU L T I P L C S E R V E R : ON
CONN E C T I ON MOD E :
AU T O
cursor buttons and
H I GH AUD I O QUA L I T Y
H I GH R E L I AB I L I T Y
or
GP I D S E T T I NG : S T AR T
MA I N
/ cursor buttons 1.
Select "9. MULTI PLC" in the SETUP MAIN
MENU with the
press the ENTER button.
2.
Select "GP-ID SETTING" with the
cursor buttons.
<ZC4001>
1. 3. 2.
1.
Press and hold the ENTER button for 5 sec or
more.
P L C
E X I T
or cursor buttons, and
or