Other Function; Display Mode; Recording An Analog Source; Selecting Analog Audio Input Or Digital Audio - Marantz SR4002/SR5002 User Manual

OTHER FUNCTION

DISPLAY MODE

ER SR5002
LEARN SEND
SOURCE SET OFF
l/
SLEEP DISPLAY DISPLAY P.DIRECT SURROUND
SURROUND PURE SIMPLE
MODE DIRECT SETUP DISPLAY MEMORY CLEAR LIP SYNC/
AUTO dts

INPUT

1 2 3
ENTER
AUTO HT-EQ MENU EXIT BAND T-MODE
CS EX/ES VIRTUAL T.MODE
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
You can select the display mode for the front display
of the unit.
To select this mode, press the DISPLAY on the
remote controller.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source
selected for listening through this unit is sent to the
record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT, VCR OUT in the record mode.
ON
To record the input source signal you are currently
watching or listening to
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
1.
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP
MULTI SPEAKER
STANDBY
AUTO HT-EQ MENU
POWER ON/STANDBY SETUP MIC PHONES
1.
Select the input source to record by turning the
INPUT SOURCE knob on the front panel or
simply press the input selector buttons on the
remote controller.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the TAPE OUT, CD/CDR OUT, VCR
OUT outputs for recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS to
video cassette recorder connected to the VCR OUT
jack.
DISC+ ANGLE
1.
CH-SEL V-OFF
BASS
TV DVD
2.
TUNER CD CD
TAPE AUX1
- PRESET + - TUNING +
REMOTE CONTROLLER
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
TV TV DVD DVD VCR VCR DSS DSS
1.
Switch the video output source to VCR by
TUNER TUNER CD CD CDR CDR MD MD
simply pressing the input selector buttons on
TAPE AUX1 AUX2 AMP
the remote controller.
REMOTE CONTROLLER
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote controller.
3.
Now "CD" has been selected as the audio input
source and "VCR" as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
SUB TITLE AUDIO
ATT.
TREBLE
VCR VCR DSS
CDR MD
AUX2 AMP
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the A/D (0) button.
When this button is pressed, the input mode is
switched in the following sequence.
→ HDMI Auto → HDMI → Digital → Analog → HDMI
Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 27)
TV DVD VCR DSS
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP AMP
REMOTE CONTROLLER
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
7.1CH IN A/D A/D HT-EQ
0 +10 +10
CL MEMO
CH/ CAT VOLUME
SPKR A/B MUTE
MULTI/ CAT M-SPKR
39