Aux2 Input; Ht-Eq (Home Theater Equalizer); Tv Auto On/Off Function; Video On/Off - Marantz SR4002/SR5002 User Manual

2. 1.
M-CH ST STEREO NIGHT
AV SURROUND RECEIVER SR5002
7 8 9
INPUT SELECTOR
2.
7.1CH IN 7.1CH IN A/D
0 0 +10
CL
CH/ CAT
SPKR A/B MUTE
4.
SURROUND PURE
MULTI MODE DIRECT MULTI/ CAT M-SPKR
MULTI SPEAKER
STANDBY
AUTO HT-EQ
POWER ON/STANDBY SETUP MIC PHONES INFO
ENTER
T.TONE
/SET UP
4.
REC T.DISP PTY
- PRESET + - TUNING
VOLUME
DISC+ ANGLE SUB TITLE
CH-SEL V-OFF ATT.
DOWN UP
1.
BASS
TV TV DVD DVD VCR VCR
MEMORY CLEAR
MUTE ATT
TUNER CD CDR
BAND T-MODE
AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
TAPE AUX1 AUX2
REMOTE CONTROLLER
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote
controller to switch the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote
controller.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
IN on the remote controller.
Notes:
• 7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.

AUX2 INPUT

If you don't need to connect 7.1 Ch. input terminals
P.SCAN
with multi channel decoder,
HT-EQ
L(front left) and R (front right) inputs terminals are
MEMO
VOLUME VOLUME
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
MENU
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
EXIT
F.DIRECT
SURROUND PURE
MULTI MODE DIRECT
MULTI SPEAKER
+
STANDBY
AUTO HT-EQ
POWER ON/STANDBY SETUP MIC PHONES
AUDIO
TREBLE
DSS DSS
MD
AMP

HT-EQ (HOME THEATER EQUALIZER)

AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP DISPLAY
MULTI SPEAKER
STANDBY ENTER
AUTO HT-EQ MENU EXIT
POWER ON/STANDBY SETUP MIC PHONES
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode
1.
Press the HT-EQ button on the unit.
"EQ" indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2.
To cancel this function, press the HT-EQ button
again.
"EQ" indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 28 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
SIMP
SETU
VIDEO input.
MEN
3.
Turn OFF the power to the TV TUNER and the
unit.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, this unit turns ON
and TV is selected automatically.
VOLUME
AUTO POWER OFF
DOWN
1.
In the above situation, turn the TV TUNER OFF
MEMORY CLEAR
or select a channel that does not contain any
MUTE
BAND T-MODE AUX 1 INPUT
broadcast.
DIGITAL S-VIDEO VIDEO L
2.
The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support "TV AUTO
ON/OFF" function.

VIDEO ON/OFF

When no video signal is connected to the unit or
a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the "VIDEO OFF" setting.
To select video off, press the AMP button and press
the V-OFF button.
TV DVD VCR DSS
TUNER CD CDR
R5002
TAPE AUX1 AUX2 AMP AMP
REMOTE CONTROLLER
SURROUND PURE SIMPLE
MODE DIRECT SETUP DISPLAY MEMORY CLEAR
REC T.DISP PTY F.DIRECT
ENTER
AUTO HT-EQ MENU EXIT BAND T-MODE
- PRESET + - TUNING
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
TV DVD VCR

LIP.SYNC (SR5002 only)

Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5002, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR5002
to correct the time lag between the sound and image.
It can be operated with the "LIP.SYNC" and 1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
The LIP.SYNC feature turns OFF (0 ms) in the
SOURCE DIRECT mode. When the SOURCE
DIRECT mode is deactivated, the set value of the LIP.
SYNC feature is automatically restored.
MD
+
DSS
41