Listening To Xm Satellite Radio (Sr5002 Only) - Marantz SR4002/SR5002 User Manual

LISTENING TO XM SATELLITE RADIO
(SR5002 ONLY)
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must
fi rst select the input source on the SR5002.
1. SOURCE SET OFF ON
l/
SLEEP DISPLAY P.DIRECT SURROUND
LIP SYNC/
AUTO dts INPUT
1 1 2 2 3 3
AV SURROUND RECEIVER SR5002
BAND
INPUT SELECTOR
CS EX/ES VIRTUAL T.MODE
4 4 5 5 6 6
M-CH ST STEREO NIGHT P.SCAN
7 7 8 8 9 9
7.1CH IN A/D HT-EQ
SURROUND PURE
MULTI MODE DIRECT
MULTI SPEAKER 0 0 +10
CL MEMO
STANDBY
AUTO HT-EQ
POWER ON/STANDBY SETUP MIC PHONES
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
TV DVD VCR DSS
TUNER TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
RC5001SR
2.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
DOWN
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP DISPLAY MEMORY CLEAR
MULTI SPEAKER MUTE
STANDBY ENTER
AUTO HT-EQ MENU EXIT BAND T-MODE
POWER ON/STANDBY SETUP MIC PHONES DIGITAL
(Using the SR5002)
1.
Turn the INPUT SELECTOR knob to select
"TUNER".
2.
Press the BAND button to select XM band.
(Using the remote controller)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
Press the BAND button to select XM band.
44
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
ENTER
T.TONE
/SET UP EXIT
REC T.DISP T.DISP PTY F.DIRECT
- PRESET + - TUNING +
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
2.
1.
Press the T.DISP button 3 times to displayed
Signal Status.
S I G N A L :
• The display changes as shown below according to
1.
the receiving condition.
SIGNAL: ■ ■ ■ ■■ ■
SIGNAL: STRONG
(Signal strength is good)
SIGNAL: ■ ■ ■ ■
SIGNAL: MARGINAL
VOLUME
(Signal strength is Marginal)
UP
SIGNAL: ■ ■
ATT
SIGNAL: WEAK
AUX 1 INPUT
S-VIDEO VIDEO L AUDIO R
(Signal strength is poor)
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
2.
Adjust the antenna location until signal strength
is good.
3. Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR5002 or the Q or
R buttons of the remote controller.
3.
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP
MULTI SPEAKER
STANDBY
AUTO HT-EQ MENU
POWER ON/STANDBY SETUP MIC PHONES
• The Radio ID is displayed.
X M O O O R A D I O
Notes:
• If "ANTENNA" appears in the front panel display,
the XM Mini-Tuner and Home Dock may not be
connected to the XM terminal on the rear panel of
this unit properly.
• The ATT function is also effective when XM is
selected.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist name/
song title, category or signal status) for the channel
INFO MENU
currently selected in the front panel display.
ENTER
T.TONE
/SET UP EXIT
REC T.DISP PTY F.DIRECT
- PRESET + - TUNING +
3.
DISC+ ANGLE SUB TITLE AUDIO
DISPLAY
CH-SEL V-OFF ATT.
ENTER
BASS TREBLE
EXIT
TV DVD VCR DSS
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
1.
Press the T.DISP button to displayed
INFORMATION.
C h a n n e l n u m b e r / n a m e
I D
A r t i s t n a m e / S o n g t i t l e
C h a n n e l c a t e g o r y
S i g n a l S t a t u s
When the Channel number/name is displayed:
X M O 4 0 : D e e p T r c
4 0 : D e e p T r a c k s
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.
ENTER
T.TONE
/SET UP EXIT
REC T.DISP T.DISP PTY F.DIRECT
1.
- PRESET + - TUNING +
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE