Basic Operation (Playback); Selecting An Input Source; Selecting The Surround Mode; Night Mode - Marantz SR4002/SR5002 User Manual

BASIC OPERATION
(PLAYBACK)

SELECTING AN INPUT SOURCE

Before you can listen to any input media, you must
fi rst select the input source on the unit.
Example : DVD
DISC+ ANGLE
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
CH-SEL V-OFF
BASS
TV DVD
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP
TUNER CD
MULTI SPEAKER
STANDBY
AUTO HT-EQ MENU TAPE AUX1
POWER ON/STANDBY SETUP MIC PHONES
REMOTE CONTROLLER
To select DVD, turn the INPUT SOURCE knob on
the front panel or simply press the DVD button on the
remote controller.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• As the input is changed, this unit will automatically
switch to the digital input, surround mode,
attenuation, and night mode status which were
entered during the confi guration process for that
source.
• When an audio source is selected, the last video
input used remains routed to the VCR Output
and Monitor Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the Monitor
Output jacks and will be viewable on a TV monitor
connected to the unit.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
34

SELECTING THE SURROUND MODE

Example: AUTO SURROUND
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP
MULTI SPEAKER
STANDBY
AUTO HT-EQ MENU
POWER ON/STANDBY SETUP MIC PHONES
SUB TITLE AUDIO
ATT.
To select the surround mode during playback, press
TREBLE the SURROUND MODE button on the front panel
VCR DSS
or the SURROUND MODE buttons on the remote
CDR MD
controller.
AUX2 AMP

NIGHT MODE

LIP SYNC/
AUTO dts INPUT
1 2 3
CS EX/ES VIRTUAL T.MODE
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
7.1CH IN A/D HT-EQ
0 +10
CL MEMO
VOLUME
CH/ CAT
SPKR A/B MUTE
Press the NIGHT button on the remote controller to
turn on the NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late at
night.
To turn off the Night mode, press the NIGHT button
again.

ADJUSTING THE MAIN VOLUME

VOLUME
SOURCE SET OFF ON
l/
DOWN UP
SLEEP DISPLAY P.DIRECT SURROUND
LIP SYNC/
SPLAY MEMORY CLEAR
MUTE ATT
AUTO dts INPUT
1 2 3
EXIT BAND T-MODE
AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
CS EX/ES VIRTUAL T.MODE
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
Adjust the volume to a comfortable level using
7.1CH IN A/D HT-EQ
0 +10
CL MEMO
the VOLUME control knob on the front panel or
VOLUME 3 / 4 buttons on the remote controller.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME 3 button on the
remote controller, to decrease the volume, turn
counterclockwise or press VOLUME 4 button on the
remote controller.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 26, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range is
"18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
- PRESET
DISC+
CH-SEL
TV
TUNER
TAPE
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote controller)
To adjust the bass effect, press BASS 3 or BASS 4
on the remote controller.
To adjust the treble effect, press TREBLE 3 or
TREBLE 4 on the remote controller.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
TEMPORARILY TURNING OFF
THE SOUND
7.1CH IN A/D HT-EQ
0 +10
CL MEMO
CH/ CAT VOLUME VOLUME
SPKR A/B MUTE
MULTI/ CAT M-SPKR
DOWN
INFO MENU ISPLAY MEMORY CLEAR
MUTE
EXIT BAND T-MODE
DIGITAL
ENTER
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording or
dubbing that may be in progress.
When the system is muted, the display will show
"MUTE" .
Press the MUTE button again to return to normal
operation.

USING THE SLEEP TIMER

+ - TUNING +
ANGLE SUB TITLE AUDIO
V-OFF ATT.
To program this unit for automatic standby, press the
BASS BASS TREBLE TREBLE
DVD VCR DSS
SLEEP button on the remote controller.
CD CDR MD
Each press of the button will increase the time before
AUX1 AUX2 AMP shut down in the following sequence.
REMOTE CONTROLLER OFF 10
120 110
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows "SLEEP OFF" and the
SLEEP indicator will disappear.
7.1CH IN A/D HT-EQ
0 +10
VOLUME
CL MEMO
CH/ CAT VOLUME
SPKR A/B MUTE MUTE
UP
MULTI/ CAT M-SPKR
ATT
AUX 1 INPUT INFO MENU
S-VIDEO VIDEO L AUDIO R
ENTER
LEARN SEND
SOURCE SET OFF ON
l/
SLEEP SLEEP DISPLAY P.DIRECT SURROUND
LIP SYNC/
AUTO dts INPUT
1 2 3
CS EX/ES VIRTUAL T.MODE
4 5 6
20 30 40 50
100 90 80 70 60