Operating Instructions; Lighting Instructions; To Turn Off Gas - Napoleon Tureen GD82NT-T Installation And Operation Instructions Manual

24
When lit for the first time, the fireplace will emit a slight odour for a
few hours. This is a normal temporary condition caused by the
curing of paints and lubricants used in the manufacturing process
and will not occur again. Simply open a window to sufficiently
ventilate the room.
After extended periods of non-operation such as following a
vacation or a warm weather season, the fireplace may emit a
FOR YOUR SAFETY READ BEFORE LIGHTING:
A. This fireplace is equipped with a pilot which must be lit by hand
while following these instructions exactly.
B. Before operating smell all around the fireplace area for gas
and next to the floor because some gas is heavier than air and
will settle on the floor.
C. Use only your hand to turn the gas control knob / manual
shut-off knob. Never use tools. If the knob will not turn by hand,
do not try to repair it. Call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under water.
Immediately call a qualified service technician to inspect the
fireplace and replace any part of the control system and any gas
control which has been under water.
Warning: if you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or
loss of life. Initial lighting of the pilot and main burners must be
done with the glass door off.
Do not connect valve or wall switch to electricity. See insta llation
instructions.
When lighting and re-lighting, the gas knob cannot be turned from
pilot to off unless the knob it depressed slightly.
1. STOP! read the safety information on the operating
label.
2. Turn off all electric power to the fireplace.
3. Turn the gas knob clockwise
4. Wait 5 minutes to clear out any gas. If you smell gas,
including near the floor, STOP! Follow "B" on the operating label.
If you don't smell gas, go to the next step.
5. If the fireplace is equipped with a flame adjustment valve, turn
clockwise to off.
6. Find pilot located in front of the back log on the right side.
1. Turn off all electric power to the fireplace if service is to be
performed.
2. For a complete shut-down procedure: push in gas control knob
slightly and turn clockwise
W415-0666 / 01.28.08

OPERATING INSTRUCTIONS

LIGHTING INSTRUCTIONS

to off.

TO TURN OFF GAS

to off. Do not force.
slight odour for a few hours. This is caused by dust particles in
the heat exchanger burning off. Open a window to sufficiently
ventilate the room.
Purge all gas lines with the glass door of the fireplace open.
Assure that a continuous gas flow is at the burner before closing
the door.
WHAT TO DO IF YOU SMELL GAS
• Do not touch any electric switch.
• Do not use any phone in your building.
• If you cannot reach your gas supplier, call the fire department.
• Turn off all gas to the fireplace.
• Do not try to light any appliance.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
FIGURE 68
7. Turn gas knob counter-clocwise
8. This unit is equipped with an auto-spark. Depress and hold
gas knob . Keep knob fully depressed for one minute, then
release. If pilot does not continue to burn repeat steps 3 through
7.
9. With pilot lit, turn gas knob counter-clockwise
10. If equipped with flame adjustment valve, push and turn knob
to high.
11. If equipped with remote on-off switch, main burner may not
come on when you turn the valve to on or high. Remote switch
must be in the on position to ignite burner.
12. Turn on all electric power to the fireplace.
FIGURE 69
3. For a temporary shut-down procedure: set thermostat to lowest
setting or remote switch to off. Press and turn the gas knob
clockwise to pilot.
GAS KNOB
to pilot.
to on.
PILOT
SOLENOID
ON/OFF
KNOB