Initialization Of B, 1B Page Data; Initializing Of B, 1B Page Data; Modification Of B, 1B Page Data - Sony DCR-TRV940 Adjustment Manual

1-2-4.

Initialization of B, 1B Page Data

Note: If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to "00".

1. Initializing of B, 1B Page Data

Note 1: If "Initialization of Pages B, 1B" is executed, all data on
pages B, 1B are initialized. (Only an individual page can-
not be initialized)
Note 2: If the B, 1B page data has been initialized, the following
adjustments need to be performed again.

1) Modification of B, 1B page data

Note 3: Check that the voltage of power supply is 6.0 ± 0.1Vdc.
Adjustment Page B
Adjustment Address 00 to FF
Adjustment Page 1B
Adjustment Address 00 to FF
Initializing method:
Order Page Address Data
1 0 01 01
2 0 10 00
3 5 02 FF
4 5 01 F3
5 5 00 01
6 5 02
7 5 0E 00
8 5 03 20
9 5 01 FA
10 5 00 01
11 5 0E
12
13
Procedure
Press PAUSE button.
Press PAUSE button.
Check the data changes to "00".
Press PAUSE button.
Press PAUSE button.
Press PAUSE button.
Press PAUSE button.
Check the data changes to
"01".
Turn off the power supply,
then turn on them again.
Perform "Modification of B
Page Data"
DCR-TRV940/TRV940E/TRV950/TRV950E
2. Modification of B, 1B Page Data
If the B, 1B page data has been initialized, change the data of the
"Fixed data-2" address shown in the following table by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages B, set data: 01 to page: 0,
address: 00, and then select pages B.
3) If modification of data on pages 1B, set data: 01 to page: 0,
address: 10, and then select pages B. After the modification of
data finished, return the data on page: 0, address: 10 to "00".
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification B page data:
Order Page Address Data
1 2 00
2 2 01
3. B Page table
Note 1: Check that the data of page: 0, address: 10 is "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the B, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of B, 1B Page Data")
Initial value
Address
NTSC PAL
00 to AF
B0
B1 to FF
4. 1B Page table
Note 1: If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the B, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of B, 1B Page Data")
Initial value
Address
NTSC PAL
00 to FF
6-21
Procedure
29
29 Press PAUSE button.
Remark
Fixed data-1 (Initialized data)
Fixed data-2 (TRV950/TRV950E)
Fixed data-1 (TRV940/TRV940E)
Fixed data-1 (Initialized data)
Remark
Fixed data-1 (Initialized data)