Accessories; General Options / Accessories; Tig Welding Options / Accessories; Semiautomatic Fcaw And Mig Welding (Ranger 300 Dlx) Options / Accessories - Lincoln Electric RANGER 300 D Operator's Manual

C-1
GENERAL OPTIONS /

ACCESSORIES

The following options/accessories are available for
your RANGER 300 from your local Lincoln Distributor.
K953-1 Two-Wheeled Trailer - For in-plant or yard
towing of the RANGER 300. Suitable for road towing
with optional Fender and Light Kit. Load capacity is
2,100 lbs.
K802-R Power Plug Kit - Provides four 15 amp, 115
volt plugs and one 50 amp, dual voltage (115/230V),
full kVA plug.
K703 Accessory Kit - Includes the following:
• Thirty-five feet (10.5 meters) of #1/0 AWG elec-
trode cable.
• Thirty feet (9.1 meters) of # 1/0 AWG work cable.
• Headshield with No. 12 filter.
• GC500 work clamp.
• Cooltong® 300 insulated electrode holder.
The cables are rated at 300 amps, 100 duty cycle.
K903-1 Spark Arrester Kit - A field-installed kit for
the RANGER 300 engine muffler exhaust pipe (either
engine option). Includes a heavy-gauge steel,
approved spark arrester, mounting clamp and
adapter.
K857 Remote Control - Includes a control box with
25 feet (7.5 meters) of 4 conductor cable. Allows out-
put voltage to be controlled remotely.
K896-1 GFCI Receptacle Kit - Includes two UL
approved 120 volt ground fault circuit interrupter
receptacles (duplex type) with covers and installation
instructions. Each receptacle is rated 15 amps, but
the maximum total current from each GFCI duplex is
limited to 20 amps. The GFCI receptacles replace the
two factory installed 120 volt duplex receptacles.
TIG WELDING OPTIONS /
ACCESSORIES
K930-1 TIG Module - The TIG Module is an accesso-
ry that provides high frequency and shielding gas con-
trol for AC and DC GTAW (TIG) welding applications.
It provides contactor control of constant current weld-
ing power sources having an internal contactor.
ACCESSORIES
The TIG Module is supplied without accessories, Arc
Start switches, Amptrols, cables, torches and mount-
ing brackets must be purchased separately.
K939-1 Docking Kit - For mounting the K930-1 TIG
Module on top of the Ranger 300.
K936-1 Control Cable - Control cable for 300 DLX for
connecting the K930-1 TIG Module to a RANGER 300
DLX.
K936-3 Control Cable - Control cable for connecting
K930-1 TIG module to a Ranger 300 D.
K814 Arc Start Switch - A remote start switch used
in conjunction with the K930-1 TIG Module to energize
the RANGER 300 DLX output terminals via the TIG
module.
K963 Hand Amptrol - Remote output control on
RANGER 300 D/DLX and contactor control on Ranger
300 DLX.
K870 Foot Amptrol - Remote output control on
RANGER 300 D/DLX and contactor control on Ranger
300 DLX.
SEMIAUTOMATIC FCAW AND MIG
WELDING (RANGER 300 DLX)
OPTIONS / ACCESSORIES
LN-25 Wire Feeder - This portable unit provides
CC/CV for flux-cored arc welding (FCAW) and metal
inert gas welding (MIG).
LN-7 or LN-8 Wire Feeder - Semiautomatic constant
speed wire feeders.
NOTE: Gas-shielded welding requires a Magnum
Gun. Gasless welding requires an Innershield Gun.
K487-25 Magnum Spool Gun - A lightweight, semi-
automatic wire feeder for aluminum welding with
argon gas. Has built-in remote wire speed control in
the handle. Requires the K488 SG Control Module.
Includes 50 feet (15.2 meters) of power cable.
K488 SG Control Module - Controls wire speed and
gas flow. Provides the required control interface
between the RANGER 300DLX and the K487-25
Magnum Spool Gun.
RANGER 300 D AND 300 DLX
C-1