Configuring An Additional Metric For A Rip Interface - HP VSR1000 Configuration Manual

12.3.1.0/24
12.3.1.0/32
12.3.1.2/32
12.3.1.255/32
16.4.1.0/24
16.4.1.0/32
16.4.1.1/32
16.4.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
3. Configure RIP route redistribution:
# Configure RIP 200 to redistribute direct routes and routes from RIP 100 on Router B.
[RouterB] rip 200
[RouterB-rip-200] import-route rip 100
[RouterB-rip-200] import-route direct
[RouterB-rip-200] quit
# Display the IP routing table on Router C.
[RouterC] display ip routing-table
Destinations : 15
Destination/Mask
0.0.0.0/32
10.2.1.0/24
11.1.1.0/24
12.3.1.0/24
12.3.1.0/32
12.3.1.2/32
12.3.1.255/32
16.4.1.0/24
16.4.1.0/32
16.4.1.1/32
16.4.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
127.0.0.1/32

Configuring an additional metric for a RIP interface

Network requirements
As shown in
E.
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Proto
Direct 0
RIP
RIP
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Direct 0
Figure 9, run RIPv2 on all the interfaces of Router A, Router B, Router C, Router D, and Router
0
0
0
0
0
0
0
0
0
0
0
0
Routes : 15
Pre Cost
0
100 1
100 1
0
0
0
0
0
0
0
0
0
0
0
0
0
43
12.3.1.2 GE1/0
12.3.1.2 GE1/0
127.0.0.1 InLoop0
12.3.1.2 GE1/0
16.4.1.1 GE2/0
16.4.1.1 GE2/0
127.0.0.1 InLoop0
16.4.1.1 GE2/0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
NextHop Interface
127.0.0.1 InLoop0
12.3.1.1 GE1/0
12.3.1.1 GE1/0
12.3.1.2 GE1/0
12.3.1.2 GE1/0
127.0.0.1 InLoop0
12.3.1.2 GE1/0
16.4.1.1 GE2/0
16.4.1.1 GE2/0
127.0.0.1 InLoop0
16.4.1.1 GE2/0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0