Table of Contents
Advertisement
NORMAL OPERATING SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds from your gas
appliance. This is perfectly normal due to the fact that there are
various gauges and types of steel used within your appliance.
Listed below are some examples. All are normal operating
sounds and should not be considered as defects in your appli-
ance.
Blower:
Regency gas appliances use high tech blowers to push heated
air farther into the room. It is not unusual for the fan to make a
"whirring" sound when ON. This sound will increase or decrease
in volume depending on the setting of your fan switch.
Burner Tray:
The burner tray is positioned directly under the burner tube(s)
and logs and is made of a different gauge material from the rest
of the firebox and body. Therefore, the varying thicknesses of
steel will expand and contract at slightly different rates which can
cause "ticking" and "cracking" sounds. You should also be aware
that as there are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal for steel firebox-
es.
Blower Thermodisc:
When this thermally activated switch turns ON it will create a
small "clicking" sound. This is the switch contacts closing and is
normal.
Pilot Flame:
While the pilot flame is on it can make a very slight "whisper"
sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a dull clicking sound
may be audible, this is normal operation of a gas regulator or
valve.
Unit Body/Firebox:
Different types and thicknesses of steel will expand and contract
at different rates resulting in some "cracking" and "ticking"
sounds will be heard throughout the cycling process.
MAINTENANCE INSTRUCTIONS
1)
Always turn off the gas valve before cleaning. For relighting,
refer to lighting instructions. Keep the burner and control
compartment clean by brushing and vacuuming at least
once a year.
When cleaning the logs, use a soft clean brush as the logs
are fragile and easily damaged.
2)
Clean appliance and door with a damp cloth (never when
unit is hot). Never use an abrasive cleaner. The glass
Regency F33-1 Freestanding Gas Stove
should be cleaned with a gas fireplace glass cleaner (when
it starts to cloud up).
3)
The heater is finished in a heat resistant paint and should
only be refinished with heat resistant paint. Regency uses
Stove Brite Paint - Metallic Black #6309.
4)
Make a periodic check of burner for proper position and
condition. Visually check the flame of the burner periodically,
making sure the flames are steady; not lifting or floating. If
there is a problem, call an authorised service person.
5)
The appliance and fluing system must be inspected before
use, and at least annually, by an authorised field service
person, to ensure that the flow of combustion and ventilation
air is not obstructed.
During the annual service call, the burners should be re-
moved from the burner tray and cleaned. Replace the
embers and rock wool.
6)
Each time the appliance is lit, it may cause condensation
and fog the glass. This condensation is normal and will
disappear in a few minutes as the glass heats up.
7)
Caution: Label all wires prior to disconnection when servic-
ing controls. Wiring errors can cause improper and danger-
ous operation. Verify proper operation after servicing.
WARNING:
CHILDREN AND ADULTS SHOULD BE ALERTED TO
THE HAZARDS OF HIGH SURFACE TEMPERATURES
AND SHOULD STAY AWAY TO AVOID BURNS OR
CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN THE
SAME ROOM AS THE APPLIANCE.
CAUTION:
ANY SAFETY SCREEN OR GUARD REMOVED FOR
SERVICING AN APPLIANCE MUST BE REPLACED
PRIOR TO OPERATING THE APPLIANCE. DO NOT SPRAY
AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE
IN OPERATION
CLOTHING OR OTHER FLAMMABLE MATERIAL
SHOULD NOT BE PLACED ON OR NEAR THE
APPLIANCE.
NEVER OPERATE THE APPLIANCE WITHOUT
THE GLASS PROPERLY SECURED IN PLACE.
MAINTENANCE
15
Advertisement
Table of Contents
