Korg D3200 Owner's Manual page 164

LoDamp (Low Damp)
HiDamp (High Damp)
Sets the damping amount in the high range
In Level (Input Level)
: Type
The left/right panning of the delay can be modified by chang-
ing the connections of the left and right delay. Be aware that dif-
ferent sounds must be input to the left and right channels in
order for this parameter to be effective.
11: St.Modulation Dly
(Stereo Modulation Delay)
This stereo delay uses an LFO to sweep the delay time. The
pitch also varies. You will obtain a delay sound with swell
and shimmering. You can also control the delay time using a
modulation source.
L Time (L Delay Time)
R Time (R Delay Time)
*LFO Speed
Dry:Wet
Sets the balance between the effect and dry sounds
*L Depth
*R Depth
Sets the depth of the right LFO modulation
LFO Wave (LFO Waveform)
LFO Shape
Determines how much the LFO waveform is changed
L Fdback (L Feedback)
R Fdback (R Feedback)
L Phase (L LFO Phase)
Sets the phase obtained when the left LFO is reset
R Phase (R LFO Phase)
Sets the phase obtained when the right LFO is reset
: L LFO Phase [degree], : R LFO Phase [degree]
"L LFO Phase" and "R LFO Phase" specify the phase differ-
ence between the two LFO's when they are reset. This allows
the pitch change of the sweep to be set independently for left
and right.
12: St.Dynamic Delay
(Stereo Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you input signals at a
high velocity or only when the volume level is low.
L Time (L Delay Time)
R Time (R Delay Time)
Feedback
Dry:Wet
Sets the balance between the effect and dry sounds
Threshold
154
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
53Hz...20.0kHz, THRU
Sets the input level to the effect
Sets the left delay time
Sets the right delay time
0.02...20.00Hz
Sets the LFO speed
Dry, 1:99...99:1, Wet
Sets the depth of the left LFO modulation
Triangle, Sine
Selects LFO Waveform
–100...+100%
–100...+100%
Sets the feedback amount of left delay
–100...+100%
Sets the feedback amount of right delay
–180...+180deg
–180...+180deg
Sets the left delay time
Sets the right delay time
–100...+100%
Sets the feedback amount
Dry, 1:99...99:1, Wet
Adjusts the level at which compression
Attack
Release
0...100% Offset
Control (Control Target)
LoDamp (Low Damp)
HiDamp (High Damp)
Spread
Polarity
: Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
0...2.500sec
: Polarity, : Threshold, : Offset, : Attack, : Release
The "Offset" parameter specifies the value for the "Control
Target" parameter (when level control is not being applied),
0...2.500sec
expressed as a ratio relative to the parameter setting.
If "Polarity" is set to [+] Plus, "Control Target" will be the
value of the parameter multiplied by the "Offset" when the
input signal is lower than the "Threshold," or will be the value
of the parameter when the input signal is above the "Thresh-
old."
If "Polarity" is set to [–] Minus, "Control Target" will be the
0...200
value of the parameter when the input signal is lower than the
"Threshold," or will be the value of the parameter multiplied
by the "Offset" when the input signal is above the "Thresh-
0...200
old."
The "Attack" and "Release" parameters specify attack time
and release time of delay level control.
13: Auto Panning Delay
This stereo delay effect pans the delay sound left and right
using the LFO.
L Time (L Delay Time)
R Time (R Delay Time)
*Speed (Panning Speed)
Dry:Wet
L Fdback (L Feedback)
R Fdback (R Feedback)
*Depth (Panning Depth)
L-R Phase (LFO L-R Phase)
Sets the LFO phase difference between the left and right
LoDamp (Low Damp)
HiDamp (High Damp)
0...2.730sec
Waveform (LFO Waveform)
0...2.730sec
LFO Shape
Determines how much the LFO waveform is changed
0...100
Sets the attack time of level control
Sets the release time of level control
Sets the offset of level control
None, WetLevel, Feedback
Selects from no control, output, and feedback
Sets the damping amount in the low range
Sets the damping amount in the high range
Sets the width of the stereo image of the effect sound
Sets the right delay time
Sets the balance between the effect and dry sounds
Sets the feedback amount for the left channel
Sets the feedback amount for the right channel
Sets the damping amount in the low range
Sets the damping amount in the high range
0...1.00sec
0...10.0sec
0...100%
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
0...100%
[+]Plus, [–]Minus
Reverses level control
0...2.730sec
Sets the left delay time
0...2.730sec
0.02...20.00Hz
Sets the panning speed
Dry, 1:99...99:1, Wet
–100...+100%
–100...+100%
0...100
Sets the panning width
–180...+180deg
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
Triangle, Sine
Selects LFO Waveform
–100...+100%