Pattern Map - Korg D3200 Owner's Manual

2. Parameters
You can use the drum track fader and key to turn the
drum track on/off and adjust the volume.
Use the Knob Matrix to adjust the send levels and EQ set-
tings. You can also click an icon in the screen and use the
value dial (or +/– keys) to edit the setting.
3. Link
Click this if you want the send and EQ parameters to be
the same values for L and R. If you want to set the param-
eters individually for left and right, click this to turn it
off, and then set the parameters individually.
4. PRE/PST
This specifies whether the sends will be taken from
before the fader (pre-fader) or from after the fader (post-
fader).
PRE: Send the pre-fader level
PST: Send the post-fader level

14-3. Pattern Map

Here you can edit the pattern map to add new events during
song recording or playback, or change the time signature,
drum pattern, or tempo.
You can specify events in the pattern map at intervals of measures.
1
1. Pattern map window
Select the pattern map event that you want to edit.
The list shows the event number, the starting measure
and ending measure for the pattern, the time signature,
the session name, the variation name, and the tempo.
2. Prev
Turn this on (highlighted) if you want to preview the pat-
tern of the event that is selected in the pattern map window.
This is valid only in this tab page, and will automatically
be switched off when you play back the recorder or move
to another page.
3. New
Creates a new pattern map event.
Click this button to add a new event.
When you click this button, the New Map Event dialog
box will open, and you will automatically be in Preview
mode (2. Prev turned on).
You can't add events if RecMode is set to Tempo.
RecMode = Pat&T
3a
3b
3c
144
[001...200]
3f
3e
3d
3a. Start Meas
Specifies the location at which the pattern map event
will be created (begun, inserted), in units of measures.
3b. Length
Specifies the number of measures for the pattern.
3c. GROUP, SESS, VARI, TEMPO
Use GROUP to select the group (type) of drumming
pattern, SESS to select a pattern set (session) from the
specified group, VARI to select a pattern variation
and TEMPO to Specifies the tempo of the drumming.
3d. Blank
Click (highlight) this to select a blank pattern.
3e. Fill
Click (highlight) this to select a fill pattern.
3f. Ending
Click (highlight) this to select an ending pattern.
4. Edit
Edits the settings of a pattern map event.
Select this if you want to modify an existing event. Select
(highlight) the event you want to modify, and click this but-
ton to display the Edit Map Event dialog box where you
can edit the parameters. (See the preceding section, 3. New)
RecMode = Pattern
2
3
4
5
6
If you set the Start Meas setting later (or earlier) than the be-
ginning of the selected event, the Length of the preceding event
will be lengthened (or shortened) by the difference.
5. Overwr.
The settings of the pattern map event will be changed by
being overwritten. Choose this if you want to add an
event without changing the length of the pattern map
you've already created. The overwritten area will be
divided as a new event. Select the event you want to
modify (it will be highlighted), click this button to open
the Overwrite Map Event dialog box, and set the param-
eters. (Refer to the preceding section, 3. New)
RecMode = Pattern
If the Start Meas and Length settings exceed the range of the
event you selected, the event(s) corresponding to that portion of
the map will also be overwritten. If the Start Meas and Length
settings are identical to the range of the event you selected, no new
event will be added; the result will be the same as 4. Edit.
6. Delete
Deletes an event from the pattern map.
In the pattern map window, select the event you want to
delete and click this button to open the Delete dialog box.
[0001...9999]
[0001...9999]