Assembly - Weider CJXT3 User Manual

ASSEMBLY

Before beginning assembly, carefully read the
following information and instructions:
• Place all parts of the CJXT3 in a cleared area
and remove the packing materials; do not dis-
pose of the packing materials until assembly is
completed.
• Read each assembly step before you begin.
• For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the centre of this manual.
Note: Some small parts may have been pre-
attached for shipping purposes. If a part is not in
the parts bag, check to see if it has been pre-
attached.
• As you assemble the CJXT3, be sure that all
parts are oriented as shown in the drawings.
1. Before you begin, make sure that you have
carefully read the instructions at the top of
this page.
Press a 2" Inner Cap (27) into the Base (4).
Attach the Pulley Plate (20) to the Base (4) with
two 5/16" x 2 3/4" Bolts (11), two 5/16" Flat
Washers (8), and two 5/16" Nylon Locknuts (3).
Insert the two 5/16" x 2 1/2" Carriage Bolts (1) up
through the Base (4).
2. Press the two 2" Outer Caps (88) onto the
Stabiliser (5).
Insert two 5/16" x 2 3/4" Carriage Bolts (14) up
through the Stabiliser (5). Slide the end of the
Base (4) and the Rear Upright (82) onto the
Carriage Bolts. Make sure that the Rear Upright
is turned as shown. Thread 5/16" Nylon
Locknuts (3) onto the two Carriage Bolts. Do not
tighten the Nylon Locknuts yet.
Attach the Brace (86) to the Rear Upright (82)
and the Stabiliser (5) with two 5/16" x 2 3/4" Bolts
(11), two 5/16" Flat Washers (8), and two 5/16"
Nylon Locknuts (3). Do not tighten the Nylon
Locknuts yet.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
• Two (2) adjustable spanners
• One (1) standard screwdriver
• One (1) phillips screwdriver
• One (1) rubber mallet
• Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
1
20
11
4
3
8
1
27
2
Bracket
Low Side
82
11
8
3
88
86
8
3
3
5
4
88
14
4
WEIGHT RESISTANCE CHART
WEIGHT PRESS ARM BUTTERFLY ARM
PLATES (lbs.) (lbs.)
1 29 26
2 48 39
3 69 50
4 83 64
5 107 80
6 129 96
7 145 112
8 163 130
9 181 149
10 200 Do not use
Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as
well as friction between the cables, pulleys, and weight guides.
(1 pound=0,454 kg.)
LEG LEVER HIGH PULLEY LOW PULLEY
(lbs.) (lbs.) (lbs.)
18 16 18
32 30 32
45 43 45
58 56 58
71 68 71
84 80 84
98 93 98
110 105 110
125 117 125
134 128 134
17