And 5/16" Nylon Locknut (3) - Weider CJXT3 User Manual

26. Press a 1 1/2" Inner Cap (32) into the Seat Frame
(36).
Insert a 1/4" x 2" Carriage Bolt (38) into the centre
of each Seat Plate (37). Attach the Seat Plates to
the Seat (13) with four 1/4" x 3/4" Screws (18).
Insert the two 1/4" x 2" Carriage Bolts (38) into
the Seat Frame (36). Make sure that the Seat
(13) is turned so the wide end is toward the
1 1/2" Inner Cap (32). Tighten a 1/4" Nylon
Locknut (7) with 1/4" Flat Washer (10) onto each
Carriage Bolt.
27. Press a 1 1/2" Inner Cap (32) into the Leg Lever
(29).
Lubricate a 5/16" x 2 1/4" Bolt (33). Attach the
Leg Lever (29) to the Seat Frame (36) with the
Bolt and a 5/16" Nylon Locknut (3). Do not over-
tighten the Nylon Locknut; the Leg Lever
must be able to pivot freely.
28. Set the bracket on the Seat Frame (36) onto the
indicated pins on the Front Upright (42). Attach
the Seat Frame with a 5/16" x 2 3/4" Carriage
Bolt (14) and the Seat Knob (40).
Press 3/4" Round Inner Caps (34) into the ends
of the 13 1/2" Pad Tube (28). Insert the Pad Tube
into the Seat Frame (36). Slide a 6" Pad (30) onto
each end of the Pad Tube.
Press 3/4" Round Inner Caps (34) into the ends
of the 13" Pad Tube (31). Insert the Pad Tube into
the Leg Lever (29). Slide a 5 1/2" Pad (50) onto
each end of the Pad Tube.
29. Press 1 1/2" Inner Caps (32) into the Left and
Right VKR Arms (100, 101).
Attach the Left and Right VKR Arms (100, 101) to
the Rear Upright (82) with two 5/16" x 2 3/4" Bolts
(11) and 5/16" Nylon Locknuts (3).
26
13
Wide
End
37
38
37
18
36
10
7
27
3
36
33—Lubricate
29
32
28
40
28
36
34
14
31
42
30
Pin
34
29
50
29
11
101
3
82
100
32
12
15. Attach the Wide Swivel Bracket (71) to the indi-
cated bracket on the Top Frame (67) with a 5/16"
x 3 1/4" Bolt (35) and 5/16" Nylon Locknut (3). Do
not overtighten the Nylon Locknut; the Wide
Swivel Bracket must be able to swivel freely.
32
16. If the parts shown at the right have not been pre-
assembled, follow the instructions below to
assemble them.
Attach the two "I" Plates (78) to two 4 1/2" Pulleys
(77) with two 3/8" x 1 3/4" Bolts (48) and 3/8"
Nylon Locknuts (21) as shown. Do not thread
the Nylon Locknuts all the way onto the Bolts
until assembly step 24 is completed.
17. IMPORTANT: As you assemble the Long Cable
(66) and the Short Cable (not shown), refer to
page 19 of this manual to make sure that the
Cables are properly routed.
30
Find the end of the Long Cable (66) that does not
have a rubber ball. Insert that end of the Long
Cable up through the indicated opening in the Top
Frame (67).
50
Lay the Long Cable (66) over a 4 1/2" Pulley (77).
Attach the Pulley inside the Top Frame (67) with a
3/8" x 2 3/4" Bolt (70), two 3/8" Flat Washers (9),
the two 1/2" x 1/2" Spacers (65), and a 3/8" Nylon
Locknut (21).
18. Remove the 3/8" x 1 3/4" Bolt (48), 3/8" Nylon
Locknut (21), and 3 1/2" Pulley (15) from the indi-
cated bracket on the Top Frame (67). Insert the
end of the Long Cable (66) through the bracket
and down through the indicated hole.
Reattach the 3 1/2" Pulley (15) to the bracket on
the Top Frame (67) with the 3/8" x 1 3/4" Bolt (48)
and 3/8" Nylon Locknut (21). Be sure that the
Long Cable is between the Pulley and the top
of the bracket.
15
35
67
3
71
16
77
48
78
21
77
78
17
66
65
77
65
9
21
9
70
67
18
Bracket
67
21
15
66
Hole
48
9