Advertisement
ORDERING REPLACEMENT PARTS
If you encounter any difficulties or problems with this product, contact the ICON Fitness Lifestyle Ltd. office, or
write:
ICON Fitness Lifestyle Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
Tel: Country Code: 0345-089009
Fax: 01789-440-798
To help us assist you, please be prepared to give the following information:
• The MODEL NUMBER of the product (WESY700921).
• The NAME of the product (WEIDER
CJXT3).
®
• The SERIAL NUMBER of the product (see the front cover of this manual).
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST/EXPLODED DRAWING
attached at the centre of this user's manual).
Part No. 131523 R0397A WEIDER is a registered trademark of ICON Health & Fitness, Inc. © 1997 Printed in USA
Model No. WESY700921
Serial No.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that
there are missing or damaged
parts, we will guarantee you
complete satisfaction through
our Customer Service
Department.
Please CALL:
0345-089009
Or WRITE:
ICON Fitness Lifestyle Ltd
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
CAUTION
Read all precautions and in-
structions in this manual before
using this equipment. Save this
manual for future reference.
USER'S MANUAL
Advertisement
Table of Contents
Related Manuals for Weider CJXT3
Summary of Contents for Weider CJXT3
-
Page 1: Ordering Replacement Parts
Read all precautions and in- structions in this manual before USER'S MANUAL using this equipment. Save this manual for future reference. Part No. 131523 R0397A WEIDER is a registered trademark of ICON Health & Fitness, Inc. © 1997 Printed in USA... - Page 2 TABLE OF CONTENTS CABLE DIAGRAM IMPORTANT PRECAUTIONS ............. .2 The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (66).
-
Page 3: Before You Begin
WESY700921. The serial number can be found on a Adjustment improve your cardiovascular system, the CJXT3 will decal attached to the CJXT3 (see the front cover of Woven cable, the type of cable used on the weight Screw help you to achieve the specific results you want. -
Page 4: Assembly
(lbs.) (lbs.) following information and instructions: instructed to do otherwise. • Place all parts of the CJXT3 in a cleared area THE FOLLOWING TOOLS (NOT INCLUDED) ARE and remove the packing materials; do not dis- REQUIRED FOR ASSEMBLY: pose of the packing materials until assembly is completed. - Page 5 ATTACHING THE LEG LEVER TO THE LOW 3. Press the 1 1/4” Inner Cap (57) into the Front Single Hole PULLEY STATION Upright (42). To use the Leg Lever (29), the seat must be attached Attach the 1” Plastic Stop (64) to the centre hole to the front upright (see ATTACHING AND REMOV- in the Stop Bracket (63) with a 5/16”...
-
Page 6: Adjustment
5. Press two 1 1/2” Bushings (93) into the Left Pedal ADJUSTMENT (90); press two 1 1/2” Bushings (93) into the Right Pedal (89). Attach a Pedal Cover (92) to each Pedal with a 1/2” Tap Screw (6). The instructions below describe how each part of the weight system can be adjusted. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position Lubricate the pedal axles on the Rear Upright Slotted... -
Page 7: Cable Diagram
Weight. Locate the lower ends of the Weight Guides (72) (there are holes near the upper ends). Insert the lower ends of the Weight Guides into the ten CJXT3 Master Trainer Weights (25). Power 200 LBS Max Bench Press... - Page 8 12. Press two 1 3/4” Inner Caps (44) into each of the 30. Attach a VKR Armrest (99) to the Right VKR Arm Arms (46). (101) with two 1/4” x 2” Screws (102) and 1/4” Flat Washers (10). Apply lubricant to the lower axles on the Arm Frame (52).
-
Page 9: And 5/16" Nylon Locknut (3)
26. Press a 1 1/2” Inner Cap (32) into the Seat Frame 15. Attach the Wide Swivel Bracket (71) to the indi- (36). cated bracket on the Top Frame (67) with a 5/16” x 3 1/4” Bolt (35) and 5/16” Nylon Locknut (3). Do Insert a 1/4”... - Page 10 19. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4” 23. Hold the indicated end of the Short Cable (23) Bolt (48), and 4 1/2” Pulley (77) from one end of under the 3 1/2” Pulley (15) on the Front Upright the “I”...
- Page 11 REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL! 3/4" Round Inner Cap (34)–4 1" Round Inner Cap (49)–2 1" Round Cover Cap (55)–4 This chart is provided to help you identify the small parts used in assembly. Important: Some parts may have been pre-assembled for shipping purposes;...
- Page 12 1/4" Nylon Locknut (7)—6 1/2" Tap Screw (6)–2 5/16" x 2 3/4" Carriage Bolt (14)–3 1/2" x 3/8" Spacer (51)— 1/4" x 3/4" Screw (18)–8 5/16" Jam Nut (2)–2 5/16" x 2 3/4" Bolt (1 1)–11 1/2" x 1/2" Spacer (65)—2 1/4"...
- Page 13 PART LIST—Model No. WESY700921 R0397A REMOVE THIS PART LIST/EXPLODED Key No. Qty. Description Key No. Qty. Description DRAWING FROM THE MANUAL! 5/16” x 2 1/2” Carriage Bolt Plastic Bushing 5/16” Jam Nut 1” Retainer 5/16” Nylon Locknut 1” Round Cover Cap Base Large “U”...
- Page 14 EXPLODED DRAWING—Model No. WESY700720 EXPLODED DRAWING—Model No. WESY700921 R0596A R0397A 68 77 15 3 21 35 21 20...
- Page 15 Model No. WESY700720 R0596A 68 77 21 3 21 20...