Weider CJXT3 User Manual page 5

ATTACHING THE LEG LEVER TO THE LOW
PULLEY STATION
To use the Leg Lever (29), the seat must be attached
to the front upright (see ATTACHING AND REMOV-
ING THE SEAT on page 15).
Attach the Chain (84) between the 13"Pad Tube (31)
on the Leg Lever (29) and the Short Cable (23) with a
Cable Clip (83) and the "S"-Hook.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
Attach the Lat Bar (85) to the Long Cable (66) with a
Cable Clip (83). For some exercises, the Chain (84)
should be attached between the Lat Bar and the Long
Cable with two Cable Clips. If the Chain is used,
adjust the length of the Chain between the Lat Bar
and the Long Cable so the Lat Bar is in the cor-
rect starting position for the exercise to be per-
formed.
The Nylon Strap (39) can be attached in the same way.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION
Attach the Lat Bar (85) to the Short Cable (23) with a
Cable Clip (83). For some exercises, the Chain (84)
should be attached between the Lat Bar and the
Short Cable with two Cable Clips. If the Chain is
used, adjust the length of the Chain between the
Lat Bar and the Short Cable so the Lat Bar is in
the correct starting position for the exercise to be
performed.
The Nylon Strap (39) can be attached in the same way.
CHANGING THE STEPPING RESISTANCE
To change the stepping resistance, first lift the Right
and Left Pedals (89, 90) off the hooks at the lower
ends of the Resistance Cylinders (91). Move the
hooks to different slots under the Pedals. Make sure
that the hooks are fully inserted into the slots in
the same position under both Pedals. The farther
the hooks are moved from the Rear Upright (82), the
greater the resistance will be. CAUTION: The
Resistance Cylinders become very hot during use.
Allow the Resistance Cylinders to cool before
touching them.
29
83
23
31
84
66
84
83
85
39
39
23
83
84
85
83
89
91
90
82
16
3. Press the 1 1/4" Inner Cap (57) into the Front
Upright (42).
Attach the 1" Plastic Stop (64) to the centre hole
in the Stop Bracket (63) with a 5/16" x 1 1/2" Bolt
(24) and 5/16" Nylon Locknut (3).
Attach the Stop Bracket (63) to the Front Upright
62
(42) with a 5/16" x 2" Bolt (61), 5/16" Flat Washer
(8), and 5/16" Nylon Locknut (3).
Slide the Front Upright (42) onto the two 5/16" x
2 1/2" Carriage Bolts (1) in the Base (4). Thread
two 5/16" Nylon Locknuts (3) onto the Carriage
Bolts. Do not tighten the Nylon Locknuts yet.
4. Press two 2" Inner Caps (27) into the Top Frame
(67).
Attach the Top Frame (67) to the Front Upright (42)
with two 5/16" x 2 3/4" Bolts (11), 5/16" Flat
Washers (8), and 5/16" Nylon Locknuts (3). Do
not tighten the Nylon Locknuts yet.
Attach the Top Frame (67) to the Stop Bracket (63)
with a 5/16" x 2 3/4" Bolt (11), 5/16" Flat Washer
(8), and 5/16" Nylon Locknut (3). Do not tighten
the Nylon Locknut yet.
Attach the Top Frame (67) to the Rear Upright (82)
with two 5/16" x 2 3/4" Bolts (11), 5/16" Flat
Washers (8), and 5/16" Nylon Locknuts (3).
Tighten all Nylon Locknuts used in steps 2
through 4.
3
Single Hole
63
3
3
64
24
8
57
61
42
4
3
1
4
11
11
11
8
8 8
67
27
3
3
63
3
42
82
5
27