Toshiba E-Studio 5540c Troubleshooting Manual page 13

Message
Cannot print this paper type
Set the other paper type
Change from this mode
Count over, cannot store anymore
READY (SADDLE STITCH TRAY
FULL)
READY (CHECK SADDLE STITCH
STAPLER)
READY (CHECK SADDLE STITCH
STAPLER)
READY (CHECK STAPLER)
READY (CHECK STAPLER)
READY (HOLE PUNCH DUST BIN IS
FULL)
READY (FINISHER FULL)
READY (INNER TRAY FULL)
Cannot copy
Check DEPARTMENT COUNTER
Add paper
CALL FOR SERVICE
Examine stapler in the saddle stitch
unit.
Check staple cartridge in the saddle
stitch unit.
Check staple cartridge
Examine stapler.
Saving energy - press START button.
CHANGE DRAWER TO CORRECT
PAPER SIZE
Problem Description
Printing was attempted but failed.
The paper could not be output in the
tray selected because of a mismatch
between the paper type and the tray.
(Special paper or thick 4 paper tried to
be output in the lower receiving tray of
MJ-1103/MJ-1104.)
The number of originals to be
scanned has exceeded the limit
specified with the department or user
code during scanning.
The saddle stitch tray of the finisher is
full of paper.
A staple jam has occurred in the
stapler of the Saddle Stitch unit.
No staples remain in the stapler of the
Saddle Stitch unit.
A staple jam has occurred in the
stapler of the Finisher.
No staples remain in the stapler of the
Finisher.
The hole punch dust bin is full of
paper punchings.
The receiving tray of the finisher is full
of paper.
The exit tray of the equipment is full of
paper.
The number of originals to be
scanned has exceeded the limit
specified with the department code
during scanning.
No paper remains in a drawer or on
the bypass tray.
The equipment requires adjusting by
a service technician.
A staple jam has occurred in the
stapler of the Saddle Stitch unit.
No staples remain in the stapler of the
Saddle Stitch unit.
No staples remain in the stapler of the
Finisher.
A staple jam has occurred in the
stapler of the Finisher.
The equipment has entered into the
energy saving mode since it has not
been used for a certain time.
No paper suitable for the original is
set.
1 TROUBLESHOOTING FOR THE HARDWARE
Corrective Action
Delete the failed print job, select the appropriate tray
for the paper, and perform printing again.
Ask your administrator for details of setting the limit for
the number of copies.
Remove the paper from the saddle stitch tray of the
finisher.
Remove the jammed staples.
P.46 "Staple jam in the Saddle Stitch unit"
Refill the staples.
P.58 "Refilling the Saddle Stitch unit staples"
Remove the jammed staples.
P.45 "Clearing a Staple Jam"
Refill the staples.
P.57 "Refilling With Staples"
Remove the paper punchings.
P.61 "Cleaning the Hole Punch Dust Bin"
Remove the paper from the receiving tray of the
finisher.
Remove the paper from the exit tray of the equipment.
Ask your administrator for details of setting the limit for
the number of copies.
Set paper in the drawer or on the bypass tray. The
touch panel indicates which drawer (or the bypass
tray) has no paper.
To set paper, refer to the Copying Guide.
Contact your service representative with the error
code (C***) displayed on the right side of the touch
panel.
Never attempt to repair, disassemble or modify
the equipment by yourself.
You could cause a fire or get an electric shock.
Always contact your service representative for
maintenance or repair of the internal parts of the
equipment.
Remove the jammed staples.
P.46 "Staple jam in the Saddle Stitch unit"
Refill the staples.
P.57 "Refilling With Staples"
Refill the staples.
P.57 "Refilling With Staples"
Remove the jammed staples.
P.45 "Clearing a Staple Jam"
Press any of the [START], [COPY], [e-FILING],
[SCAN], [PRINT], [FAX] and [ENERGY SAVER]
buttons to clear the energy saving mode.
Place suitable size paper for the original in the drawer.
Messages Displayed on the Touch Panel 11