Operation Example - Icom IC-FR3000 Series Sales Handbook

3-6-5

1 1 1 1 - - - - 5 OPERATION EXAMPLE

5 OPERATION EXAMPLE
5 OPERATION EXAMPLE 5 OPERATION EXAMPLE
System control command System control command System control command System control command
NOTE: NOTE: NOTE: NOTE:
▒
▒ • All commands must be entered within 10 sec. of
▒ entering a password. If the input time period runs
▒ out, you must enter the password again. This time
period cannot be changed, so it is possible to
▒
enter the password and command continuously.
▒
▒
• When operating from the phone line the phone
▒
must be able to send DTMF signals.
▒
• When the command is available from the
▒
transceiver and phone line, the operations are not
▒
different from both them other than the
▒
connecting and disconnecting way to the repeater.
▒
Repeat Start (0003 Default) Repeat Start
Repeat Start Repeat Start
This command is available from both the transceiver
and phone line. This explanation shows the step by step and phone line. and phone line. and phone line.
operation from the transceiver or operation from the
phone line when entering the password and command
continuously (one after the other). continuously (one after the other).
[From the Transceiver] [From the Transceiver] [From the Transceiver] [From the Transceiver]
① Enter the programmed password from the
transceiver.
Code: ∗0001#
• Verify the repeater replies "System Password OK
ACK (1111)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone and de-limiter
tone are correct, and try again.
② Enter the "Repeat Start" command within 10 sec.
Code: ∗0003#
• Verify the repeater replies "OK ACK (3333)."
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0003#).
• The repeater starts the repeater operation.
[From the Phone line] [From the Phone line]
[From the Phone line] [From the Phone line]
① Dial the phone number of the phone line that the
repeater is connected to.
② When the connection has been confirmed, enter the
following DTMF code.
Code: ∗0001#0003#
• Verify the repeater replies "OK ACK (3333)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone, de-limiter tone
and Repeat Start code are correct, and try again.
• The repeater starts the repeater operation.
③ Hang up the phone, the repeater automatically
disconnects the phone.
Operation Example
both the transceiver
both the transceiver both the transceiver
The following examples assume these codes
are pre-programmed in the repeater. Other
commands are the same as default codes listed on
command table (p. 36).
System Password: 0001,
Header Tone: ∗, De-limiter Tone: #
System Password OK ACK: 1111
System Control Exit ACK: 2020
OK ACK: 3333, NG ACK: 4040
Repeat Stop (0004 Default) Repeat Stop
Repeat Stop Repeat Stop
This command is available from both the transceiver
and phone line. This explanation shows the operation and phone line. and phone line. and phone line.
from the transceiver when entering the password and
command continuously or step by step operation from
the phone line (one after the other). the phone line (one after the other).
[From the Transceiver] [From the Transceiver] [From the Transceiver] [From the Transceiver]
➥ Enter the following DTMF code from the transceiver.
Code: ∗0001#0004#
• Verify the repeater replies "OK ACK (3333)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone, de-limiter tone
and Repeat Stop code are correct, and try again.
• The repeater stops the repeater operation.
[From the Phone line] [From the Phone line] [From the Phone line] [From the Phone line]
① Dial the phone number of the phone line that the
repeater is connected to.
② When the connection has been confirmed, enter the
programmed password.
Code: ∗0001#
• Verify the repeater replies "System Password OK
ACK (1111)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone and de-limiter tone
are correct, and try again.
③ Enter the "Repeat Stop" command within 10 sec.
Code: ∗0004#
• Verify the repeater replies "OK ACK (3333)."
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0004#).
• The repeater stops the repeater operation.
④ Hang up the phone, the repeater automatically
disconnects the phone.
both the transceiver
both the transceiver both the transceiver
38