Phone Patch - Icom IC-FR3000 Series Sales Handbook

3-7
Basic Repeater to Phone Line Connecting System Basic Repeater to Phone Line Connecting System Basic Repeater to Phone Line Connecting System Basic Repeater to Phone Line Connecting System
The IC-FR3000/FR4000 repeater can be connected
directly to the telephone line.
When a subscriber transmits a DTMF dialing codes, the
repeater, received signal is sent to the telephone line to
connect the phone.
Tx = f
1
Rx = f
2
Tx = f
Rx = f
UHF H/H
DTMF Setting DTMF Setting DTMF Setting DTMF Setting
To enable connect phone line functions, the DTMF
settings must be pre-programmed using CS-FR3000
cloning software. Use CS-FR3000 help screens for
description of functions and operation and for description of functions and operation and for
programming details.
▒ NOTE NOTE NOTE NOTE: Cannot call to phone line from transceiver
▒ when the repeater is working in PMR mode and the
▒ operating channel of 5-Tone format is set to DTMF.
Operation from the transceiver Operation from the transceiver Operation from the transceiver Operation from the transceiver
One of two methods (Dial and Auto-dial) of telephone
access is selectable from the transceiver.
Auto-dial: Using the pre-programmed phone No. (up
to 20 channels are stored) in the repeater.
Dial: Direct dialing from the keypad of a transceiver.
TEL Autodial (0016 Default) TEL Autodial
TEL Autodial TEL Autodial
Autodial number: 12 (Channel 12)
① Enter the following DTMF codes.
Code: ∗0001#0016#12#
• Verify the repeater replies "OK ACK (3333)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone, de-limiter tone
and command code are correct, and try again.
• The repeater starts calling the autodial channel
12.
② When the connection has been confirmed, talk to the
phone by simplex voice communication.
③ After conversation is finished enter the password
followed by the "System Control Exit" command to
terminate Phone Patch operation.
Code: ∗0001#0002#
• Verify the repeater replies "System Control Exit
ACK (2020)," then repeater hangs on the phone.
Phone Patch – Transceiver to Phone
IC-FR4000
2
1
System requirement System requirement System requirement System requirement
Descriptions
UHF Repeater
UHF Antenna
Duplexer
Telephone Line
Public Telephone Line
TEL Dial (0015 Default) TEL Dial TEL Dial TEL Dial
① Enter the programmed password from transceiver.
Code: ∗ 0001#
∗
• Verify the repeater replies "System Password OK
ACK (1111)." ACK (1111)."
• If the repeater replies "NG ACK (4040)," make
sure the password, header tone and de-limiter tone
are correct, and try again.
② Enter the "TEL Dial" command within 10 sec.
Code: ∗0015#
• Verify the standby time runs out, enter the
password and command continuously (Code:
∗0001#0015#).
③ Enter the telephone number (if the number is 060-
3355-2244) as sub code within 10 sec.
Code: ∗06033552244#
• Verify the repeater replies "OK ACK (3333)."
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗0001#0015#06033552244#).
• The repeater starts calling the number.
④ When the connection has been confirmed, talk to the
phone by simplex voice communication.
⑤ After conversation is finished enter the password
followed by the "System Control Exit" command to
terminate Phone Patch operation.
Code: ∗0001#0002#
• Verify the repeater replies "System Control Exit
ACK (2020)," then repeater hangs on the phone.
Model Number Quantity
IC-FR4000
45